Vision Fitness X6600HRT User manual

Guide
Assembly
X6600HRT ELLIPTICAL TRAINER

elliptical trainer
X6600HRT
1
STEP
2
STEP
6
STEP
4
STEP
5
STEP
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding
though, find your new Elliptical Trainer’s serial number located below the power switch, and enter here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Elliptical Trainer, to prevent
loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
3
STEP
8
STEP
7
STEP

5MM Allen Wrench
Screwdriver
TOOLS & PARTS INCLUDED
PARTS BOX
Lower Handlebar Rubber Boot, Qty: 2 • Console Mast Cover Plate, Qty: 1
Console, Qty: 1 • Power Supply, Qty: 1 • Water Bottle & Bracket, Qty: 1
Heart Rate Chest Strap, Qty: 1 • Parts Bags
Owner’s Guide • Assembly Guide • Warranty Card

ORANGE BAG BLUE BAG
HARDWARE INCLUDED
M8 x 75MM Bolt
Quantity: 2
M4 x 15MM Screw
Quantity: 4
M3 x 10MM Screw
Quantity: 1
M8 x 20MM Bolt
Quantity: 8
M8 Arc Washer
Quantity: 4

5
1
STEP
1
STEP
• Remove the console mast cover
from the frame.
• Slide the console mast cover onto
the console mast.
• Unfold the console cable and
attach it to the string located inside the
console mast. Guide the wire up
through the mast while simultaneously
sliding the console mast onto the
frame bracket.
• Bolt the mast to the frame with the
two bolts (M8 x 75MM), using the
5MM Blue-handled Allen Wrench.
Make sure these are tight!
• Attach the console mast cover to the
frame using four screws (M4 x 15MM).
• Attach the console mast cover plate
with the V-head screw (M3 x 10MM).
ORANGE BAG
2
STEP
• Install the rubber boot over the top
of the lower left handlebar and slide
halfway down the handlebar.
RUBBER BOOT
2
STEP

6
3
STEP
• Mount the lower left handlebar
to the frame tube using two bolts
(M8 x 20MM) and two arc washers
(M8). Now slide the rubber boot all
the way down over the handlebar.
BLUE BAG 3
STEP
4
STEP
4
STEP
• Mount the upper left handlebar
to the handlebar extension and lower
portion of handlebar using two bolts
(M8 x 20MM).
BLUE BAG
5
STEP
• Install the rubber boot over the top
of the lower right handlebar and slide
halfway down the handlebar.
RUBBER BOOT
5
STEP

7
6
STEP
• Mount the lower right handlebar
to the frame tube using two bolts
(M8 x 20MM) and two arc washers
(M8). Now slide the rubber boot all
the way down over the handlebar.
BLUE BAG 6
STEP
7
STEP
• Mount the upper right handlebar
to the handlebar extension and lower
portion of handlebar using two bolts
(M8 x 20MM).
BLUE BAG
7
STEP

8
621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2001 Vision Fitness. All Rights Reserved. 3.01 Part #Z66EPO5-AG1805PRD
AG18.05PRD
REV2
8
STEP
• Remove the four screws from the
back of the console. Plug the wire
connectors from inside the mast into
the console. The cable connectors
are slotted, so do not force the
connection!
• Mount the console to the mast
using the four screws. Do not pinch
the cable!
• Mount the Water Bottle cage to the
console mast using the included
screws.
CONSOLE
8
STEP