Vision Fitness X6000DA User manual

Guide
Assembly
X6000DA & X6200HRT/DA
DUAL-ACTION ELLIPTICAL TRAINERS

To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding
though, find your new Elliptical Trainer’s serial number, located on the front foot axle tube, and enter here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Elliptical Trainer, to prevent
loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
dual-action elliptical trainers
1
STEP
2
STEP
3
STEP
4
STEP
5
STEP
X6000DA X6200HRT/DA

5MM Allen Wrench
13MM Wrench
Screwdriver
5MM L-Shaped Wrench
TOOLS, HARDWARE, & PARTS INCLUDED
PARTS BOX
Rear Folding Axle, Qty: 1 • Stabilizer w/ Rubber Cover, Qty: 2
Toe Pieces, Qty: 2 • Rear Wheels, Qty: 2
Tension Control Knob, Qty: 1 (Model X6000DA only)
Console, Qty: 1 • Power Supply, Qty: 1 (X6200HRT/DA only)
• 13MM Nut Cap, Qty: 2 • Water Bottle & Bracket, Qty: 1 •
Heart Rate Chest Strap, Qty: 1 (Model X6200HRT/DA only)
Parts Bags • Owner’s Guide • Assembly Guide • Warranty Card
PINK BAG
M8 x 80MM Bolt
Quantity: 4
M8 x 45MM Bolt
Quantity: 2
(X6000DA only)
M8 Nylock Nut
Quantity: 4
ORANGE BAG
M8 x 16MM Bolt
Quantity: 4

BLACK BAG
BLUE BAG
GREEN BAG
M8 x 16MM Bolt
Quantity: 2
M16 Wavy Washer
Quantity: 2
M8 Washer
Quantity: 2
M16 Washer
Quantity: 2
M8 Lock Washer
Quantity: 2
M5 x 25MM Bolt
Quantity: 1
(X6000DA only)
M8 x 60MM Bolt
Quantity: 2
M8 Washer
Quantity: 2
M8 x 36MM Bolt
Quantity: 2
M8 x 12MM Bolt
Quantity: 4
M8 x 25 Washer
Quantity: 2
M16 Wavy Washer
Quantity: 2
M26 Wavy Washer
Quantity: 2
M8 x 35 Washer
Quantity: 2
M8 x 13MM Nylock Nut
Quantity: 2
M6 x 12MM Bolt
Quantity: 2

2
STEP
X6200HRT/DA
Only
5
1
STEP
1
STEP
• Install the left and right stabilizers with
the four bolts (M8 x 16MM), using the
Blue 5MM Allen wrench.
• Cover both stabilizers with the
included rubber covers.
• Insert the rear folding axle shaft into
the rear tube.
ORANGE BAG
2
STEP
• Slide a wavy washer (M16) onto
the right-hand side of the rear folding
axle, followed by the right-hand pedal
arm guide rail (the guide rails each
have a blue indicator arrow printed
on their sides; these arrows should
face to the outside).
• Slide a flat washer (M16) onto the
right-hand side of the rear axle,
followed by a rear wheel.
• Slide the large flat washer
(M8) onto the right-hand side of the
rear axle, and secure with a bolt
(M8 x 16MM).
• Repeat above steps to install left-
hand pedal arm guide rail.
• X6200HRT/DA only: Slide the toe-
piece onto the pedal arm while
simultaneously lifting the locking knob.
Lock the toe-piece into place at the
STEP or GLIDE position.
BLUE BAG

X6000DA
Only
3
STEP
6
3
STEP
• Mount the rear pedal arms to the
front pedal arms using four bolts
(M8 x 80MM) and four M8 NyLock
nuts. Tighten with the 13MM wrench.
• X6000DA only: Install the foot toe
pieces to the front pedal arms with
two bolts (M8 x 45MM) using the Blue
5MM Allen wrench.
PINK BAG

7
4
STEP
• X6000DA only: Unfold the RPM
sensor wire, located in the frame console
mast bracket. Remove any kinks.
• All models: Slide the rubber console
mast cover onto the bottom of console
mast, and slide it up as far as it will go.
• All models: Unfold the console cable
and attach it to the string located at the
bottom of the console mast. Guide the
wire up through the mast while
simultaneously sliding the console mast
onto the frame bracket.
• All models: Bolt the console mast
to the frame bracket with two bolts
(M8 x 60MM), two flat washers
(M8), and two lock washers (M8).
Tighten with the Blue 5MM Allen
wrench. Slide the rubber console mast
cover back down over the bolt heads.
X6000DA NOTE: Be sure the RPM
sensor wire exits through the small slot
at the top right side of the console
mast.
• X6000DA only: Install the batteries
in the console. Mount console to
console mast using the four screws.
Plug the RPM sensor wire into the
back of the console, and feed the
excess back down into the small slot
in the console mast.
• X6000DA only: Turn the tension
knob to Level 15. Reach inside the
console mast and connect the magnet
cables. Turn the knob to Level 1 and
mount the knob using a bolt (M5 x 25MM).
• X6200HRT/DA only: Remove the
four screws from the back of the
console. Plug the wire connector from
inside the mast into the console. The
cable connector is slotted, so it may
only be connected one way; do not
force it!
• X6200HRT/DA only: Mount the
console to the mast using the four
screws. Do not pinch the cable!
• All models: Bolt the water bottle
cage to the console mast using the
two bolts located in the mast.
GREEN BAG
X6200HRT/DA
X6000DA
X6000DA
Only
4
STEP

8
621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2001 Vision Fitness. All Rights Reserved. 4.01 Part #Z60EP08-AG1801PRD
AG18.01PRD U.S. Patent No. 6,190,289
REV3
5
STEP
• Slide a large wavy washer
(M26) onto the console mast axle.
Locate and slide the right upper
handlebar bracket onto the console
mast axle and attach with a washer
(M8 x 35) and M8 NyLock nut, using
the 13MM wrench. Snap the plastic
13MM nut caps over the nuts.
• Slide a small wavy washer (M16)
onto the lower pedal arm support,
followed by the right lower arm.
Attach with a washer (M8 x 25) and
bolt (M8 x 12MM), using the Blue 5MM
Allen wrench.
• Pivot the lower arm and insert the
top end into the upper handlebar
bracket. Attach with bolts (M7 x 35MM)
and (M6 x 12MM) through the side,
and bolts (M8 x 12MM) from the front.
Tighten using the Blue 5MM Allen
wrench.
• Repeat the above steps to attach the
left-hand upper and lower arms.
BLACK BAG
5
STEP