Vision Fitness X6200 Frame 9 User manual

Assembly
Guide
X6200
FOLDING ELLIPTICAL TRAINER

1
STEP
2
STEP
4
STEP
3
STEP
5
STEP
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding, find
your new Elliptical Trainer’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Elliptical Trainer. If any parts, hardware or tools are missing, please call
1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Elliptical Trainer to prevent
loosening and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before
completely tightening any ONE screw.
Assembly
Guide
X6200
FOLDING ELLIPTICAL TRAINER
6
STEP
OPTIONAL

17mm WrenchScrewdriver 5mm L-Shaped Wrench
HARDWARE, TOOLS & PARTS INCLUDED
PARTS BOX
Console Mast Boot, Qty: 1
Dual Action Link Arm Covers, Qty: 2
Dual Action Axle Covers, Qty: 2
Rear Stabilizers, Qty: 2
Pedal Support Bracket, Qty: 2
Water Bottle & Cage, Qty: 1
Power Supply, Qty: 1
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
6mm L-Shaped Wrench
13mm Wrench

HARDWARE INCLUDED
BLUE BAG
BLACK BAG
GREEN BAG
M20x29x1.5T
Wavy Washer
Quantity: 2
ORANGE BAG
M8x20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 3
M8x60L Cap Screw
Quantity: 3
M5x10x1.2T Washer
Quantity: 2
M10 Nut
Quantity: 2
M5x12L Screw
Quantity: 2
M10x25x1.5T Washer
Quantity: 4
M8 Nut
Quantity: 4
M4x15L PanHead Screw
Quantity: 2
M5x12L Screw
Quantity: 4
M5x10x1T
Washer
Quantity: 4
M10x30x2T Washer
Quantity: 2
M25x34x2T Wavy Washer
Quantity: 2
M8x25x1.5T Washer
Quantity: 2 M8x35x2T Washer
Quantity: 2
M8x14x1.5T Washer
Quantity: 2
Rubber Nut Cap
Quantity: 2
Link Arm Bushing
Quantity: 2
M8x30L Screw
Quantity: 2
M8x13L Screw
Quantity: 6
PINK BAG

5
1
STEP
1
STEP
• For ease of assembly place a block
of wood (about 1” thick) under the rear
of the frame. Slide the axle through the
rear support tube. On the left side of
the axle slide on the left guide rail and
the left stabilizer. Secure in place with
the screw (M8x20L) and washer
(M8x14x1.5T). On the right side of
the axle slide on the right guide rail
and the right stabilizer. Secure in place
with the screw (M8x20L) and washer
(M8x14x1.5T). Tighten with the 5mm
Allen Wrench.
ORANGE BAG
2
STEP
• Place a teflon washer (10x25x1.5T)
on the threaded stud of the rotation
linkage.
• Place the bracket end of the pedal
arm over the rotation linkage so that
the threaded stud on the linkage inserts
through the hole on the pedal arm
bracket. Fix in place with a
teflon washer (10x25x1.5T) a washer
(10x30x2T) and nut (M10). Tighten
with the 17mm wrench.
• Place the pedal arm bracket cover
over the bracket and secure in place
with the washer (5x10x1.2T) and
screw (M5x12L). Tighten with the
Phillips screwdriver.
• Repeat steps on the opposite side.
BLUE BAG
2
STEP
Rotation
Linkage
Pedal Arm
Bracket Cover

6
3
STEP
3
STEP
• Slide the rubber boot on to the
console mast.
• Unfold the wire harness located in
the frame bracket. Wrap the wire tie
coming from the bottom of the console
mast around the end of the wire
harness. Pull the wire tie and wire
harness up through the top of the
console mast while simultaneously
sliding the mast into the frame
bracket.
• Secure the mast to the frame using
three lock washers (M8) and three
capscrews (M8x60L). Tighten with the
6mm Allen wrench.
• Slide the rubber boot down the
console mast and snap it in place
on top of the side cover.
• Remove the four screws from the
back of the console with the Phillips
screwdriver. Connect the wire harness
to the plug in the back of the console.
Attach the console to the console mast
with the four screws removed at the
beginning of this step.
• Attach waterbottle cage.
PINK BAG

7
4
STEP
• Slide a wavy washer (M20x29x1.5T)
on the lower link arm axle, which is
located under the foot plate. Slide the
axle through the bracket located on top
of the pedal arm.
• Secure the lower link arm in place by
attaching the pedal support bracket and
screw (M8x13L). Secure the outside
holes in the support bracket to the
footplate with two screws (M8x13L).
Tighten all screws with the 5mm Allen
wrench.
• Repeat same step on opposite side
GREEN BAG
4
STEP

8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2003 Vision Fitness. All Rights Reserved. 8.03 Part #Z62EP34C-AG1828PRD
AG18.28PRD
REV1
5
STEP
• On the right side, slide the dual
action axle cover into place on the
axle located on the console mast.
Slide a wavy washer (M25x34x2T)
onto the axle. Slide the right dual-
action arm into place on the axle. Fix
in place with the washer (M8x34x2T)
and locknut (M8). Cover with the
included nut cap.
• Make sure the spacer is in place in
the socket joint of the lower link arm.
Connect the lower link arm to the
dual-action arm with a screw
(M8x30L), washer (M8x25x1.5T),
and nut (M8). Tighten with the 6mm
Allen wrench and 13mm wrench.
• Position the link arm cover into
place over the joint of the lower link
arm and the dual action arm. Secure
the two pieces of the cover together
by inserting and tightening a screw
(M5x12L) in the front of the cover.
Connect the cover to each side of the
lower link arm with a washer
(M5x10x1T) and screw (M4x15L).
• Repeat these steps on the left side.
BLACK BAG
6
STEP
OPTIONAL
Dual-Action
Axle Cover
Link Arm
Covers
6
STEP
• NOTE: Elliptical Trainer cannot be
folded with the child safety guards in
place.
• Line up the grooves on the child
safety guards with the screws on the
guide rails. Slide the safety guard into
place on the guide rails. Tighten the
screws with the Phillips screwdriver to
lock in place.
SAFETY GUARDS
OPTIONAL