Vision Fitness X6000 User manual

Guide
Assembly
X6000 & X6200HRT
ELLIPTICAL TRAINERS

elliptical trainers
To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding
though, find your new Elliptical Trainer’s serial number, located on the front foot axle tube, and enter here:
Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records.
Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each bolt as you assemble your Elliptical Trainer, to prevent
loosening and noise. Also, during each assembly step, ensure that ALL nuts and bolts are in place and partially threaded in before
completely tightening any ONE bolt.
X6200HRTX6000
1
STEP
2
STEP
4
STEP
3
STEP

5MM Allen Wrench
13MM Wrench
Screwdriver
5MM L-Shaped Wrench
TOOLS & PARTS INCLUDED
PARTS BOX
Rear Folding Axle, Qty: 1
Rubber Boot, Qty: 2
Toe Pieces, Qty: 2
Rear Wheels, Qty: 2
Console, Qty: 1
Tension Control Knob, Qty: 1
(X6000 only)
Power Supply, Qty: 1
(X6200HRT only)
Water Bottle & Bracket, Qty: 1
Heart Rate Chest Strap, Qty: 1
(X6200HRT only)
Other Parts Bags
Owner’s Guide
Assembly Guide
Warranty Card

ORANGE BAG
PINK BAG
BLUE BAG
GREEN BAG
HARDWARE INCLUDED
M8 x 16MM Bolt
Quantity: 2
M16 Spring Washer
Quantity: 2
M8 Washer
Quantity: 2
M16 Washer
Quantity: 2
M5 x 25MM Bolt
Quantity: 1
(X6000 Only)
M8 x 60MM Bolt
Quantity: 2
M8 Lock Washer
Quantity: 2
M8 Washer
Quantity: 2
M8 x 20MM Bolt
Quantity: 8
M8 x 80MM Bolt
Quantity: 4
M8 Nylock Nut
Quantity: 4
M8 x 45MM Bolt
Quantity: 2
(X6000 only)
M5 x 25MM Bolt
Quantity: 4
(X6200HRT only)
M5 Flat Washer
Quantity: 4
(X6200HRT only)

X6000
Only
X6200HRT
Only
5
1
STEP
2
STEP
• Slide the front foot axle into the
plastic sleeve of the front foot. Place a
wavy washer (16 x 29 x 1.5) on
each end of the axle.
• Place a transport wheel on each
end of the axle.With the blue-
handled 5MM Allen wrench, tighten
bolts (M8x20L) and washers
(8x30x1.5) to each end of the axle to
secure the transport wheel.
BLUE BAG
2
STEP
1
STEP
• Insert the rear folding axle shaft into
the rear tube.
• Slide a spring washer (M16) onto
the right-hand side of the rear folding
axle, followed by the right-hand pedal
arm guide rail (the guide rails each
have a blue indicator arrow printed
on their sides; these arrows should
face to the outside).
• Slide a flat washer (M16) onto the
right-hand side of the rear axle,
followed by a rear wheel.
• Slide the large flat washer
(M8) onto the right-hand side of the
rear axle, and secure with a bolt (M8
x 16MM).
• Repeat above steps to install left-
hand pedal arm guide rail.
• X6200HRT only: Screw the locking
knob into the top toe piece. Place the
top and bottom toe pieces onto the
pedal arm and attach with two
washers (M5) and two bolts
(M5 x 25MM).
ORANGE BAG

6
3
STEP
• X6000 only: Unfold the RPM sensor
wire, located in the frame console
mast bracket. Remove any kinks.
• All models: Slide the rubber console
mast cover onto the bottom of console
mast, and slide it up as far as it will
go.
• All models: Unfold the console
cable and attach it to the string
located at the bottom of the console
mast. Guide the wire up through the
mast, while simultaneously sliding the
console mast onto the frame bracket.
X6000 NOTE: You will also slide the
tension cable up through the mast at
this point.
• All models: Bolt the console mast
to the frame bracket with two bolts
(M8 x 60MM), two flat washers
(M8), and two lock washers (M8).
Tighten with the Blue 5MM Allen
wrench. Slide the rubber console mast
cover back down over the bolt heads.
X6000 NOTE: Be sure the RPM
sensor wire exits through the small slot
at the top right side of the the console
mast.
• X6000 only: Install the batteries into
the console. Mount console to console
mast, using the four screws. Plug the
RPM sensor wire into the back of the
console, and feed the excess back
down into the small slot in the console
mast.
• X6000 only: Turn the tension knob
to Level 15. Reach inside the console
mast and connect the magnet cables.
Turn the knob to Level 1 and mount the
knob using a bolt (M5 x 25MM).
• X6200HRT only: Remove the four
screws from the back of the console.
Plug the wire connector from inside
the mast into the console. The cable
connector is slotted, so it may only be
connected one way; do not force it!
CONTINUE...
PINK BAG
OR
X6200HRT
X6000
X6000
Only
3
STEP
• X6200HRT only: Mount the
console to the mast using the four
screws. Do not pinch the cable!
• All models: Bolt the water bottle
cage to the console mast using the
two bolts located in the mast.
CONTINUED

7
621-D East Lake Street • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone [phone] • fax [phone]
www.visionfitness.com
2001 Vision Fitness. All Rights Reserved. 5.01 Part #Z60EP19-AG1804PRD
AG18.04PRD U.S. Patent No. 6,190,289
REV2
4
STEP
• Insert the right upper hand rail into
the upper hand rail support located
on the console mast just below the
console.
• Slide the rubber boot onto the right
lower hand rail. Slide one end of the
right lower hand rail into the right
upper hand rail. Insert the other end
into the lower hand rail support,
located on the lower portion of the
frame just ahead of the rear transport
wheels.
• Secure the hand rail together
using the hand rail attachment bolts
(M8 x 20MM).
• Repeat the above steps to attach the
left-hand upper and lower hand rails.
GREEN BAG
4
STEP