Vision VE810 S5 User manual

© 2018 Vision Engraving & Routing Systems
Vision VE810 Engraver S5
Installation Guide
Revised: 11/5/2018Part number 12-1085-01

All rights reserved. No parts of this work may be reproduced in any form or byany means - graphic, electronic, or
mechanical, including photocopying, recording, taping, or information storage and retrieval systems - without the
written permission of the publisher.
Products that are referred to in this document may be either trademarks and/or registered trademarks of the
respective owners. The publisher and the author make no claim to these trademarks.
While every precaution has been taken in the preparation of this document, the publisher and the author assume no
responsibilityfor errors or omissions, or for damages resulting from the use of information contained in this
document or from the use of programs and source code that may accompanyit. In no event shall the publisher and
the author be liable for any loss of profit or any other commercial damage caused or alleged to have been caused
directly or indirectly by this document.
Revised: 11/5/2018
Vision VE810 Engraver S5 Installation
Guide
© 2018 Vision Engraving & Routing Systems

3Contents
3
© 2018 Vision Engraving & Routing Systems
Table of Contents
Part I Introduction 4
................................................................................................................................... 51 Computer Requirements
................................................................................................................................... 62 General Electrical and Facility Requirements
................................................................................................................................... 63 VE810 Engraver Installation Layout
Part II Vision Software Installation 7
Part III Machine Setup 18
................................................................................................................................... 211 Direct Connection to Computer
................................................................................................................................... 272 Network Connection

Vision VE810 Engraver S5 Installation Guide4
© 2018 Vision Engraving & Routing Systems
1 Introduction
This guide contains information to prepare the new owner of a Vision Express for the proper installation of
their machine. It is the customer's responsibility to read through this guide and make sure the work area,
electrical and computer requirements are met. If for any reason, there are questions about these
requirements, please call your Vision representative as soon as possible.
In the following sections, the complete machine and Vision software installation will be outlined.
Please call your distributor or the service department at Vision for assistance if you have any questions
with this procedure.
FOR MORE DETAILED INFORMATION, PLEASE REFER TO THE USER GUIDE FOR YOUR MACHINE
INSTALLED WITH THE VISION SOFTWARE. USER GUIDES ARE ALSO AVAILABLE ONLINE AT
http://www.visionengravers.com/support/vision-engraver-manuals.html
Important Note:
The Vision software is available in two versions; one with a dongle, and one
that is "dongle-less" and is loaded on to a USB Memory stick. If your machine
was delivered with, or you currently have the white/blue or orange software
dongle, DO NOT LOSE IT!
The Vision software will NOT run without the dongle plugged into the computer.

Introduction 5
© 2018 Vision Engraving & Routing Systems
1.1 Computer Requirements
Minimum System
Requirements:
CPU:
Dual Core (2.0GHz or higher)
Hard Drive:
750 GB free space
RAM:
1GB + OS Requirements
Operating System:
Windows 10 (32/64 bit)
Windows 8 (32/64 bit)
Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1
Ports:
USB port for security dongle
Local or network Ethernet port to connect machine
Suggested System
Requirements
CPU:
Core i3 (or faster)
Hard Drive:
1 TB (or more)
RAM::
4GB + OS Requirements
Operating System:
Windows 10 (32/64 bit)
Windows 8 (32/64 bit)
Windows 7 SP.1 (32/64 bit) ***Requires Service Pack 1
Ports
USB port for security dongle
Local or network Ethernet port to connect machine

Vision VE810 Engraver S5 Installation Guide6
© 2018 Vision Engraving & Routing Systems
1.2 General Electrical and Facility Requirements
Machine Model
Requirements
VE810
One 110 VAC 15 Amp or One 220 VAC 10 Amp
Single Phase
Optional Equipment
Engraving Vacuum Chip Removal System
One 110 VAC 15 Amp
NOTE: In addition to the above requirements, a standard outlet is required for the
computer.
1.3 VE810 Engraver Installation Layout
VE810 Layout Diagram

Introduction 7
© 2018 Vision Engraving & Routing Systems
2 Vision Software Installation
Insert the Vision USB dongle into the USB port on the computer. Navigate to the Devices and Drives
area on your PC. Double click on the Vision icon to open the files on the USB dongle.
Select the Start or Start.exe file to begin.
Click on the Install Vision Software button.

Vision VE810 Engraver S5 Installation Guide8
© 2018 Vision Engraving & Routing Systems
The Vision S5 Software Wizard will guide you through the process of installing the software. Press Next
to continue.
Press Install to continue

Vision Software Installation 9
© 2018 Vision Engraving & Routing Systems
Setup wizard will install the program.
Select Finish to continue the software installation.
Choose your preferred language and click ok.

Vision VE810 Engraver S5 Installation Guide10
© 2018 Vision Engraving & Routing Systems
The Vision 10 Setup Screen will appear. Press Next.
After accepting the license agreement, click on the Next button.

Vision Software Installation 11
© 2018 Vision Engraving & Routing Systems
Select Next (or change the destination folder - not recommended).
Select Next to create the folder.

Vision VE810 Engraver S5 Installation Guide12
© 2018 Vision Engraving & Routing Systems
The installation will continue.

Vision Software Installation 13
© 2018 Vision Engraving & Routing Systems
Select the VE810 S5 by placing a check mark in the box to the left of VE810 in the Manufacturer list,
then select Next. If you purchase another engraving system from Vision, it can be added to the machine
list at a later date from within the Vision software.
Select the VE810 S5. Note – The VE810 Vice/Center Origin S5 is used when using the center vice
accessory.

Vision VE810 Engraver S5 Installation Guide14
© 2018 Vision Engraving & Routing Systems
Select Continue to install True Type fonts and Vision Engraving Fonts on your computer.

Vision Software Installation 15
© 2018 Vision Engraving & Routing Systems
Click yes to install all additional fonts from your C:\ Drive.
All system fonts will be installed.

Vision VE810 Engraver S5 Installation Guide16
© 2018 Vision Engraving & Routing Systems
Press OK
Press on the Finish button.

Vision Software Installation 17
© 2018 Vision Engraving & Routing Systems
Press the Exit button .
The Vision manuals icon should now appear on your computer's desktop along with an icon for your
version of Vision 10 software.

Vision VE810 Engraver S5 Installation Guide18
© 2018 Vision Engraving & Routing Systems
3 Machine Setup
On the rear of the VE810, there are four connection ports. The input power, the RJ-45 Ethernet port, the
USB port and the remote vacuum chip removal system on/off port.
VE810 (rear view)
Connect the power supply cord to a 100 - 240 volt AC power source. Then plug the power cable into the
port on the back of the machine. Plug one side of the network cable (black network cable) to the back of
the machine and the other side to either the PC Ethernet port, a network switch box or a company
network port.
NOTE: The Ethernet crossover cable is gray and should not be needed.
If the emergency stop screen appears on the LCD when the machine is powered on, then the emergency
stop button is pressed in. Release the button twisting it until it "pops up". This will clear the emergency
stop screen.

Machine Setup 19
© 2018 Vision Engraving & Routing Systems
The VE810 IP address configuration setup will vary depending on how it is connected to the PC.
The two options for connecting the VE810 to the computer are:
- Direct connection to the computer or direct connection using a network hub or switch. Both of these
methods require the same setup.
- Connection through a company network

Vision VE810 Engraver S5 Installation Guide20
© 2018 Vision Engraving & Routing Systems
Follow the steps from one of the two sections below to configure the IP address depending on the
connection type above.