Visionis VIS-3008 User manual

Access Control Outdoor IP68 Weatherproof
Card Reader / Keypad Standalone No Software
Wiegand 26-37 Bits Delay and On/Off Toggle
Mode 125KHz EM Cards 2,000 Users
www.visionistech.com
User Manual
VIS-3008

1
1. Description
3. Specification
The device is a WIFI access control keypad and proximity card reader which
supports EM & MF card types, it’s one of the most advanced standalone
access control. It adopts unique design and durable backlight keyboard,
builds-in USA Atmel microprocessor, with strong anti-interference ability, high
security and reliability, powerful function and convenient operation. It’s widely
used in high-end buildings, residential communities and other public places.
• Ultra-low power consumption: Standby current is less than 30mA.
• Input & Output: Wiegand26.
• Searching Time: Less than 0.1s after reading card.
• Backlight Keypad: Easy to operate at night.
• Doorbell interface: Support external wired doorbell.
• Access ways: Card, code, card+code.
• Card Type: EM/Mifare/HID/CPU
• Working Voltage: DC12V-24V
• Reading Range: 2~6cm (0.79~2.37in.)
• Capacity: 2000 Users
• Door Opening Time: 0~99s
• Alarm Output Load: ≤20A; Standby Current: ≤30mA; Lock Output Load: ≤3A
• Door Relay Time: 0 ~ 99s (adjustable)
• Short-circuit Protection Output Time: ≤100μS
• Operating Temperature: -40°C ~ 60°C (-40°F ~ 140°F)
• Dimensions: 111Lx46Wx22H (mm) - 4.37Lx1.82Wx0.87H (in.)
• Protection Level: IP68 - No ingress of dust; complete protection against contact
(dust tight), and waterproof
4. Sound and Light Indication
2. Features
Operate Status LED Light Color Buzzer
Standby Red
Keypad Beep
Operation Successful Green Beep－
Operation Failed Beep-Beep-Beep
Entering into Programming Red Beep－
Programmable Status Orange
Exit Programming Flash Red Slowly Beep－
Door Opening Green Beep－
Alarm Flash Red Quickly Alarm

2
5. Programming Guide
6. Advance Setting
1. Add Users
Change the master code Default factory master
code is 999999. The user
could be set factory
default if the master code
is forgotten
* The master code # 0
New code # New code #
Cards can be added
continuously
Cards can be deleted
continuously
Add card user
Delete a PIN code or a card
user
Delete all users
Add public PIN code There is only 1 public code
Delete public PIN
* The master code # 1
Read card #
* The master code # 2
Read card #
* The master code #
6 6 # 4-6 digits #
* The master code #
6 7 # 4-6 digits #
* The master code
20000 #
Add card Cards can be added
continuously
* The master code # 1
Read card # ... #
Automatic generation ID
number from number
1-2,000
Add user with specify ID
number, easily find and
delete.
Add card number
Add ID number+card
* The master code # 1
8 digits or 10 digits #
* The master code # 1
ID number # Read card #
Function Operation Steps Notes
Function Operation Steps Notes

3
Add ID number+card
number
Add user with specify ID
number, easily find and
delete.
* The master code # 1
ID number # 8 digits #
The PIN is any 4-6 digits,,
ID number is from
1-2,000, PIN Code 1234 is
not available.
Add PIN code user * The master code # 1
ID number # Pin code
#
2. Delete Users
Function Operation Steps Notes
Delete card Cards can be deleted
continuously
* The master code # 2
Read card # ... #
When the card is broken or
get lost, you can delete the
user by card number
When the card is broken
or get lost, you can delete
the user by ID number
Delete card number
Delete ID number
* The master code # 2
8 digits or 10 digits #
* The master code # 2
ID number #
Delete ALL PIN code,
card users and public PIN
code.
Delete ALL users * The master code # 2
0000 #
3. Access Ways
4. Relay Output Time
Function Operation Steps Notes
By card Only the card user could
unlock the door, keypad is
invalid
To enable this function, the
user PIN code has to be
changed.
Both card user and PIN
users could unlock the
door
By card+PIN code
By card or PIN code
* The master code #
3 1 #
* The master code #
3 2 #
* The master code #
3 0 #
Time range is from “0〜
300 seconds”，default 5
seconds
Set door unlock time * The master code # 4
0〜300 #

4
5. Alarm Time
6. Door Open Detection / WIFI / Public PIN / Data backup
Time range is from “0〜99
min ”，default 0 min
Alarm Time * The master code # 5
0〜99 #
Disable door contact Not detect the door open
status (Default)
* The master code #
6 0 #
There is only 1 public
code
Enable door contact
Add public PIN code
Delete public PIN code
Data backup sending
Delete public PIN code
DATA backup receiving
* The master code #
6 1 #
* The master code #
6 7 #
* The master code #
6 8 #
* The master code #
6 9 #
Function Operation Steps Notes
Detect door open or
closed, and alarm is
activated under abnormal
situation
* The master code #
6 6 # 4-6 digits #
7. Security Mode
Normal mode ( Default)
* The master code #
7 0 #
The device will alarm if input
10 times invalid cards or
codes continuously.
Lock mode
Alarm mode
* The master code #
7 1 #
* The master code #
7 2 #
Function Operation Steps Notes
The device will be locked
for 10 minutes if input 10
times invalid cards or
codes continuously

5
Indicator light always on ( Default)
* The master code #
8 0 #
( Default)
Indicator light always off
Beeper turn on
Beeper turn off
Keypad backlight always on
Turn it off when the beeper
is unnecessary
Keypad backlight on
Keypad backlight off
Keypad backlight always off
* The master code #
8 1 #
* The master code #
8 3 #
* The master code #
8 4 #
* The master code #
8 5 #
Function Operation Steps Notes
Turn it off when the
indicator is unnecessary
Keypad backlight
automatically
(Factory default）read a
valid or invalid card or
press the keypad, the light
will off after 10 secs.
* The master code #
8 6 #
After read a card, door
keep open, read again,
door keep close
Standalone mode
Latch mode
Reader mode
Reader mode
Factory default output is
WG26 output
WG26 output
WG34 output
Reader mode
* The master code #
8 7 #
* The master code #
8 9 #
* The master code #
8 9 2 6 #
Factory default
* The master code #
8 2 #
* The master code #
8 8 #
* The master code #
8 9 3 4 #

6
1. Drill the hole according to the size of the product
2. Fix the bottom shell with equipped screws.
3. Thread the lead wire from back cover.
4. Wrap the unused wires to avoid short circuit.
5. After wire connected, assemble the case, then finished.
8. Revise user PIN code（Don’t need go to programming state）
Revise user PIN code by
card * Read card 1234 # New PIN code #
Repeat new PIN code # Factory default code: 1234
Revise user PIN code by
mater code
* ID number # Old PIN code # New PIN code
# Repeat new PIN code #
Function Operation Steps
9. Relieve alarm (Don’t need go to programming state)
When external alarm or buzzer alarm, read a Valid card or input Master code # ,
relieve alarm
Reset to factory default
Power off, press # or press exit button, then power on, when heard sound ”beep,
beep”, succeed to reset *Reset to factory default wont delete user data
7. Installation

8. Wiring diagram
9. Diagram
7
No. Marks Color Description
1 BELL_A Pink Doorbell one end
2 BELL_B Pink Doorbell on the other end
3 D0 Green Wiegand output
4 D1 White Wiegand output
5 OPEN Yellow
6 DC12V Red Positive of power supply
7 GND Black Negative of power supply
8 NO Blue Relay NO end
9 COM Purple
Relay COM end
10 NC Orange
Relay NC end
Exit button one end(On the other
end connects GND）(Optional)
9.1 Common Power Supply

8
9.2 Special Power Supply
9.3 Reader Mode

9
9.4 Connection with Accessories: Doorbell and Exit button
9.5 Connection with Accessories: Doorbell, Exit button, and Wireless
Receiver
Power
Supply
Electromagnetic Lock
Exit Button
COM
NO
(COM)
PURPLE WIRE
Keypad/Reader
FROM KEYPAD/READER
(NC)
ORANGE WIRE
PINK WIRE
(BELL B)
FROM
KEYPAD/
READER
GREEN WIRE
FROM DOOR
BELL
FROM KEYPAD/READER
(OPEN)
YELLOW WIRE
PINK WIRE FROM
KEYPAD/READER
(BELL A)
Door Bell YELLOW WIRE
FROM DOOR BELL
FROM KEYPAD/READER
Exit
Button
COM
COM
NO
NO
NC
Power
Supply
Receiver
Power
Supply
Power
Supply
Electromagnetic Lock
Keypad/Reader
ORANGE WIRE FROM
KEYPAD/READER
PINK WIRE FROM
KEYPAD/READER
(BELL B)
PINK WIRE FROM
KEYPAD/READER
(BELL A)
YELLOW WIRE
Door Bell
YELLOW WIRE FROM KEYPAD/READER
PURPLE WIRE FROM
KEYPAD/READER