Vivo DESK-V103E User manual

Controller for Electric Height
Adjustable Desk Frame
User Guide
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-Model: DESK V1 3E
Controller
Operating Instructions
When the system is powered on, you will hear a beep and the existing
desktop height will be displayed on the control panel.
While the unit is powered on, press the downward arrow until the desk moves into
a fully lowered position. Again, press the downward arrow until “RST” is displayed.
Once the display shows “62.0”, release the downward arrow button. The desk will
move upward for approximately 10mm and come to a stop.
Touch the upward or downward arrow until desk reaches desired height.
To store a certain height in the controller’s memory, first touch “M”. The letter “S-”
will be displayed. Now touch “1”, “2”, or “3” within five seconds to store the current
height in memory. Each number can store a different height. Once in memory, you
can select any of the 3 height settings by pressing the corresponding button.
Touching any button (except for “T”) will stop the automatic adjustment.
When no actions are made for over 10 minutes, the system will enter power-
saving mode. Touch any button to enter operation mode.
Reset Mode
Upward and Downward Movement
- Power saving Mode
Memory Mode
1

To set the reminder timer, press “T”. The display will flash “0. h” representing 30
minutes. Press the “T” repetitively to increase 0. hours (30 minutes) at a time.
The maximum timer setting is two hours. The timer is set when the digit stops
flashing and the light in the top right corner of the controller is on. When the
timer has reached the set time, a beep will sound, reminding the user to adjust
his/her working position. Once a timer setting has expired, the unit’s timer is
cancelled. To de-activate the timer, press the “T” five times until the current
height is displayed and the light found in the upper right side of the controller is
off.
You can prevent accidental operation by pressing and holding the “M” button for
3 seconds, placing the unit into Screensaver Mode. The screensaver is activated
when the display shows “ - - - ”. The Screensaver Mode will also become active
should if there is no activity over 90 seconds. To turn off the screensaver, touch
and hold the “M” button for 3 seconds.
The preset measurement shown on the display is cm. If you would like to change
cm to inch, please restart the system and press the button “T” for 8 seconds.
After the buzzer beeps twice, the measurement is successfully reset. If you
would like to switch inch back to cm, please restart the system and press the
button “T” for 8 seconds. After the buzzer beeps once, the system is successfully
switched to cm measurement again.
1. Self-protection function: The unit will enter protective mode should the system
operate in excess of two minutes with “HOT” on the controller display. The system
will reset and return to normal operation after approximately 18 minutes.
2. Over-current protection mode: While operating, should the load on the desk
exceed rated specifications (1000N), the system will enter into an over-current
protection mode. This will protect the system from any damage. When this
happens, the desk will move downward approximately 30mm and come to a stop
with the current height displayed.
3. Attention: NEVER remove or turn off the power in order to reset the unit when it
is in a protective mode or “HOT” state.
4. Please reset in case two legs are different in height.
Timer Reminder Mode
Screensaver Mode
Switch Display from Centimeter to Inch
Notes
*Find troubleshooting guide on back cover.*
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If you receive any damaged or defective parts, please contact
us. We are happy to replace parts to ensure you have a fully
functional product.
Contact us at
Error Code Description
ER1 Overload in downwards direction has occurred
and needs to be reset.
ER2 Over-heating in the controller has occurred and
needs to cool.
ER3 Motor cable connection fault.
ER4 Both legs have different heights and need to be
reset.
ER Motor fault.
Troubleshooting Guide
2
Last updated: 4/17/2018
Online Version