Vivo STAND-V102Y User manual

Dual Monitor Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v102y
SKU: STAND-V102Y
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
A (x1)
Clamp Brace
B(x1)
Clamp
C(x1)
Monitor Arm
D(x1)
Pole
E(x2)
M6x10
F (x3)
M6x16
G(x1)
4mm Allen
Wrench
H (x1)
6mm Allen
Wrench
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x8)
M4x12
M-B (x8)
M5x12
M-C (x8)
D5 Washer
TOOLS NEEDED
17.6lbs
(8 kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver PER MONITOR
I (x1)
Grommet Base
J (x1)
Support Plate
K (x4)
So Pad

3
ASSEMBLY STEPS
STEP 1
OPTION A: Clamp Installation
Attach clamp (B) to the upper or lower holes of the clamp brace (A) using M6x10 flat head bolts (E),
and tighten using the 4mm Allen wrench (G). Attach the pole (D) to the clamp brace using M6x16 flat
head bolts (F). Tighten using the 4mm Allen wrench. Attach the assembled clamp to your desktop.
OPTION B: Grommet Installation
Remove the screw in the top of the hand bolt on the clamp (B) and remove the hand
bolt from the clamp. Stick so pads (K) to the bottom of the grommet base (I). Place
the grommet base and pole (D) over the grommet hole in the desktop, making sure the
pin on the base is aligned with the small hole in the pole. Place the support plate (J)
onto the hand bolt, and screw in from underneath to secure the base and pole to the
grommet hole.
NOTE: If desk does not have an existing grommet hole where needed, drill a hole using
a 3/8” (10mm) bit.

4
STEP 2
Slide the monitor arm (C) onto the pole to the desired height, and tighten the center bracket to the
pole using the 6mm Allen wrench (H).
STEP 3
Attach two bolts (M-A or M-B) and washers (M-C) to the top mounting
holes of each monitor, making sure to leave 3mm of thread exposed.

5
STEP 4
Align bolts (M-A, M-B) in VESA plates. Secure using two more bolts (M-A or M-B) and
washers (M-C) in the bottom two holes of each monitor. Tighten all bolts using a Phillips
screwdriver.

6
STEP 5
Tighten or loosen the tilt joints using the 6mm Allen wrench (H). Store tools in the cable clip.
Adjust as Desired

7

LAST UPDATED: 03/05/2020
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303