Vivo MOUNT-VWSF1 User manual

TV Wall Mount and Entertainment Shelf
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/mount-vwsf1
[email protected]om www.vivo-us.com 1-800-371-5654
SKU: MOUNT-VWSF1

2 3
PACKAGE CONTENTS
TOOLS NEEDED
100lbs
(45.36kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Mount
B(x2)
Plastic Cover
C(x1)
Cable Clip
W-A (x3)
Bolt
M-A (x4)
M6x14
M-B (x4)
M8x20
M-C (x4)
M8x50
M-D (x4)
Spacer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualied technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specied in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
W-C (x1)
Washer
W-B (x3)
Anchor
Drill
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [email protected], or call us at 1-800-371-5654.
D(x4)
VESA Adapter
E(x4)
M6x15
A2 (x1)
Shelf Bracket
B2 (x1)
Shelf
C2 (x2)
Shelf Clip
D2 (x2)
M5x8
E2 (x2)
Suction Cup
W-A2 (x3)
Bolt
W-C2 (x3)
Washer
W-B2 (x3)
Anchor
F(x4)
M6 Nut
TV MOUNT ASSEMBLY STEPS
STEP 1
OPTION A: Wood Wall
Use mount (A) to mark mounting holes on wall where stud is located. Using a 3/16” bit, drill
approximately 2.2” into marked locations. Screw top two bolts (W-A) in making sure to leave 3mm of
threads exposed.
OPTION B: Concrete/Brick Wall
Use mount (A) to mark mounting holes on wall. Using a 3/8” bit, drill approximately 2.4” into marked
locations. Insert wall anchors (W-B) and screw in top two bolts (W-A) making sure to leave 3mm of
threads exposed.
AW- A
X
3m m
W- A
W- B
3m m

4 5
STEP 2
Mount VESA adapters (D) to VESA
plate using bolts (E) and nuts (F)
in the appropriate conguration
to match your television
mounting holes.
STEP 5
Insert plastic covers (B) as shown in diagram.
STEP 3
STEP 4
Slide mount (A) over two bolts (W-A) already
inserted into wall and insert third bolt and
washer (W-C) into bottom hole. Tighten
using phillips head screwdriver.
STEP 6
Attach cable management clip (C) to bottom of
mount (A).
Aer placing TV on a at surface, attach VESA plate to back using bolts (M-A, M-B). Make sure top of
mount is facing top of TV. If bolts are too long, spacers (M-D) may be required as shown in diagram. If
you use a Samsung TV with deeper VESA holes, please use M8x50 screws and Samsung spacers (these
spacers are included with Samsung TV).
STEP 7
Run cables through cable management clip (C)
and adjust monitor to desired angle as shown in
diagram.
SHELF ASSEMBLY STEPS
STEP 1
OPTION A: Wood Wall
Using the shelf bracket (A2) as a guide, mark the mounting holes on the wall where a stud is located.
With a 4mm bit, drill approximately 2” into wall. Using bolts (W-A2) and washers (W-C2), mount the
shelf bracket (A2) onto wall. Ensure the mounting screws are anchored into the center of the studs. The
use of a stud nder is highly recommended.
F
E
D
400m m
300m m
300m m
400m m
400mm
200m m
D
E
F
M- A
M- B
M- B
M- D
W- C W- A
B
C
2 3
180°
+20°
-20°
1
A2
X
W- A2
W- C2

6 7
STEP 1 (Continued)
OPTION B: Concrete/Brick Wall
Using shelf bracket (A2) as a guide, mark mounting holes on wall. With a 5/16” bit, drill approximately
2.2” into wall. Insert concrete anchors (W-B2), bolts (W-A2) and washers (W-C2) to mount the shelf
bracket (A2) onto wall as shown in diagram.
STEP 4
Slide shelf (B2) into clips (C2).
STEP 5
Use bolts (D2) to attach the shelf (B2) into place using a phillips head screwdriver as shown in the
diagram.
Insert plastic clips (C2) into shelf bracket (A2).
STEP 2
Attach suction cups (E2) to shelf bracket (A2) as shown in diagram.
STEP 3
STEP 6
Place desired objects on shelf.
W-B2
W- A2
W- C2
C2
E2
B2
D2
D2

Last Updated: 10/08/2018
If any parts are received damaged or defective, please contact us. We are happy to
replace parts to ensure you have a fully functioning product.
For more VIVO products, check out our website at:
www.vivo-us.com.
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
[email protected]om www.vivo-us.com 1-800-371-5654