Vivo MOUNT-V101G1/W User manual

Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
https://vivo-us.com/products/mount-v101g1
SKU: MOUNT-V101G1/W
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
Pneumatic Arm Single Ultrawide Monitor Wall Mount
Instruction Manual

2
PACKAGE CONTENTS
TOOLS NEEDED
2.2-44lbs
(1-20kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
A (x1)
Wall Bracket
B (x1)
Lower Arm
C (x1)
Gas Spring Arm
S-A (x1)
Keyed Spacer
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot
be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate
use.
NOTE: SOME HARDWARE INCLUDED MAY NOT BE USED
M-A (x4)
M4x12mm Screw
D (x1)
VESA Plate
E (x1)
Round Screw Cap
F (x1)
Oval Screw Cap
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
M-B (x4)
M5x12mm Screw
M-C (x4)
M5 Washer
T-B (x1)
6mm Allen Wrench
T-A (x1)
3mm Allen Wrench
S-B (x1)
M8x25mm Screw
W-A (x3)
ST6.3x55mm Screw
W-B (x3)
Concrete Anchor
W-C (x3)
M6 Washer
CAUTION!
DO NOT INSTALL INTO DRYWALL ALONE. VERIFY YOUR WALL CONSTRUCTION. USE WOOD STUDS TO
MOUNT. We include mounting for brick and concrete walls. If unsure, please contact us at vivo-us.
com, email at [e-mail], or call us at 309-278-5303.
Drill
LevelRatchet
Stud Finder

3
ASSEMBLY STEPS
STEP 1 (Option A)
STEP 1 (Option B)
OPTION A: Wood Wall Installation
Use Wall Bracket (A) to mark drilling locations on the wall where a stud is located. Use of a level and stud
finder is recommended. Using a 3/16” (4.5mm) bit, drill 2.2” (55mm) deep holes into marked locations.
Secure Wall Bracket (A) to the wall using ST6.3x55 Screws (W-A) with M6 Washers (W-C) and a 10mm
socket wrench. Insert Round Screw Cap (E) and Oval Screw Cap (F) into the mounting holes.
OPTION B: Concrete/Brick Wall Installation
Use Wall Bracket (A) to mark drilling locations on the wall. Use of a level is recommended. Using a 3/8”
(10mm) bit, drill 2.4” (60mm) deep holes into marked locations. Insert Concrete Anchors (W-B) into
predrilled holes. Secure Wall Bracket (A) to the wall using ST6.3x55 Screws (W-A) with M6 Washers (W-C)
and a 10mm socket wrench. Insert Round Screw Cap (E) and Oval Screw Cap (F) into the mounting
holes.
A
W-AW-A
W-CW-C
AA
W-AW-A
W-BW-B W-CW-C FF
EE
EE
FF

4
STEP 2
Assemble Lower Arm (B) and Gas Spring Arm (C) to Wall Bracket (A). Tighten set screws on Wall Bracket
(A) and Lower Arm (B) using 3mm Allen Wrench (T-A).
STEP 3
Connect VESA Plate (D) to Gas Spring Arm (C) using Keyed Spacer (S-A), M8x25mm Screw (S-B), and
6mm Allen Wrench (T-B). Ensure that hexagon side of Keyed Spacer (S-A) is facing upward towards
VESA Plate (D). Remove Thumbscrew (D1) from back of VESA Plate (D). Separate Front VESA Plate (D2)
from Back VESA Plate (D3). Set aside.
T-AT-A
C
B
AA
D
C
S-A
S-B
T-B
D1
D2
D3

5
STEP 4
Connect Front VESA Plate (D2) to back of monitor using appropriate Screws (M-A, M-B), M5 Washers
(M-C), and a Phillips Screwdriver.
STEP 5
To mount the monitor, begin by lining up the tabs on Front VESA Plate (D2) with the slots on Back VESA
Plate (D3). Insert tabs into slots and re-install Thumbscrew (D1) into Back VESA Plate (D3) to secure.
D2
M-A
M-B
M-C
D2
D3
D1

6
STEP 6
While holding Gas Spring Arm (C) in the horizontal position, adjust the gas spring tension using 6mm
Allen Wrench (T-B).
STEP 7
Remove the cable management cover from Gas Spring Arm (C) using a Phillips screwdriver. Slide The
cable management cover from Lower Arm (B) o. Route cables and reattach cable management covers.
CAUTION - To avoid damage to the monitor and mount, always
keep the arm in a horizontal position while making adjustments.
ARM DROPS - If the arm drops,
turn the adjustment screw counter
clockwise until it holds the monitor
in a horizontal position.
How to adjust if...
ARM RISES - If the arm raises up,
turn the adjustment screw lockwise
until it holds the monitor in a
horizontal position.
B
C
C
T-B

7
STEP 8
For safety, please do not extend the monitor behind the desk. This may cause instability and tip the
desk over.

LAST UPDATED: 01/19/2023
REV1
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303