Vivo STAND-V012 User manual

    

Instruction Manual
Email: [email protected]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
-  
1
Scan the QR code with your mobile device or
follow the link to helpful videos and specifications
related to this product.
 
phillips screwdriver
 
- -!""## $%"!" #
 &'
 
( &'
%!
 &'
%! (
 &'
)# %
 &'
 
* &+'
,- (
. &'

/ &'
!! 
0 &'
 1 
2 &'
3 (
4 &'
 (
5 &'
! 1 
 &'
2%% (

-  &+'
1 !
6 &'
 07
 &'
1
8 &3'
-  %9 (
 &3'
-+ (
 &3'
- !
-  &-'
1 !
-   &'
: 
-   &'
: 

%97 !
%9    
2
Remove the grub screws with provided
Allen key (O).
Connect the poles (A) by threads.
Install the previously removed grub
screws and fasten them with the Allen
key (O).
!  4       !
1. Install the clamp brace (C) to the pole (A) using 3 M x14 bolts (F), see
Figure 1.
2. Attach soft pad (T-1) to the clamp brace (C), see Figure 2.
3. Install the clamp (B) to the pole assembly according to the thickness of
the desktop. The thickness can be changed to three positions. Connect it
using 2 bolts (G), and tighten using the Allen key (O). Tighten the clamp
to the desktop using the plastic knob, see Figure 3.
6!   %! 4
6! ( 2%% ( 4
 2%% . 4
If the existing grommet hole comes
with a plastic protector, remove it to
ensure a flat surface before installing
the desk mount.
1. Install the grommet base plate (M)
to the pole (A) using 3 bolts (F), see
Figure 4.
2. Attach soft pad (T-2) to the
grommet base plate (M), see Figure .
3. Position the pole (A) on the
mounting surface and secure using
the support plate (J), M10 washer (K),
spring washer (L) and M10 bolt (I).
Fasten the M10 bolt using provided
wrench (P), see Figure 6.
*


- 

(
 9
6
2
*  *  * +
* ;
* - * ,

*
- 
/
0
5
4

3
! +         
*  ) *
(
*  ) #
  (
: Hand tighten screws to avoid over tightening.
! -    )# %
Slide the monitor onto the head
of swivel arm (D) as shown in
the above diagram.
Install the security nut (H).
Make sure the security nut is
installed before you rotate the
monitor.
8


.

* <
* = * 3

*
- 
/
0
5
4
!  4 %    
Install swivel arm (D) to the pole (A). Fasten the bolt with supplied Allen
key (O). Attach the wire clip (N-1, N-2) to the pole (A) and swivel arm (D).
!  &'
6!  2%% ( 4
:  2%% . 4
1. Position the pole (A) on the mounting
surface and mark the center hole. Drill a
3/8" (10mm) diameter hole at the
marked position through the mounting
surface.
2. Install the grommet base plate (M) to
the pole (A) using 3 M x14 bolts (F), see
Figure 7.
3. Attach soft pad (T-2) to the grommet
base plate (M), see Figure 8.
4. Position the pole (A) on the mounting
surface and secure using the support
plate (J), M10 washer (K), spring washer
(L) and M10 bolt (I). Fasten the M10 bolt
using provided wrench (P), see Figure 9.
6

- 
- 

4
If you do not understand these directions, or if you have
any doubts about the safety of the installation, please call a
qualified technician. Check carefully to make sure there are
no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for
any purpose that is not explicitly specified in this manual.
We cannot be liable for damage or injury caused by
incorrect assembly or inappropriate use.
Email: [e-mail]
Live chat: www.vivo-us.com
Call: 1-800-371- 6 4
For more VIVO products, check out our
website at
www.vivo-us.com.
If any parts are received damaged or defective, please
contact us. We are happy to replace parts to ensure you
have a fully functional product.
:7 1
  
Last updated: 4/24/2018
! , *      5# 
Tighten the bolt with the
supplied Allen key (O) to fix the
tilt angle.
Remove the nut (H) and turn the
bolt to raise or lower the monitor
using the Allen key (O). Replace
nut (H) after adjustment.
! ;  * >%   9
Use the supplied Allen key (O) to
make any necessary adjustments.
Manage cables and store the Allen
keys (O) in wire clip (N-1) for future
use.
6
- 
6
6