Vivo STAND-V155C User manual

Single Wide Screen TV Desk Mount
Scan the QR code with your mobile device or follow the link
for helpful videos and specifications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v155c
SKU: STAND-V155C
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
PACKAGE CONTENTS
WARNING!
A (x1)
VESA Plate
B(x1)
Pole
C(x1)
Pole Cap
J (x1)
3mm Allen
Wrench
If you do not understand these directions, or if you have any doubts about the safety of the
installation, please call a qualified technician. Check carefully to make sure there are no missing or
defective parts. Improper installation may cause damage or serious injury. Do not use this product
for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
NOTE: NOT ALL HARDWARE INCLUDED WILL BE USED
D(x1)
Clamp
E(x1)
Cable Clip
F (x1)
Decorative
Cover
G(x1)
Grommet Base
Plate
H (x5)
Rubber Pad
I (x1)
Grommet Plate
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR
STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
K (x1)
4mm Allen
Wrench
M-A (x4)
M5x14
M-B (x4)
M6x14
M-C (x4)
M6x30
L (x2)
Arm
M (x2)
Arm
M-F (x4)
D5 Washer
M-D (x4)
M8x30
M-E (x4)
M8x50
O (x2)
Bolt
N (x8)
Screw
P (x2)
Nut
Q (x1)
Wrench
M-G (x4)
D8 Washer
M-H (x8)
D8 Washer
M-I (x8)
Spacer

3
ASSEMBLY STEPS
STEP 1
TOOLS NEEDED
66lbs
(29.94kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
Phillips
Screwdriver
Place pole cap (C) onto pole (B).
STEP 2
OPTION A: Clamp Installation
Slide cable management clip (E) and decorative cover (F) onto pole (B). Then thread pole (B) into base
of clamp (D). Tighten grub screws with allen wrench (J) as shown in diagram. Slide decorative cover (F)
down. Apply rubber pads (H) as shown in diagram. Secure clamp (D) to desk.
B C
10-88mm
E
F
D
BH
J

4
STEP 2 (Continued)
OPTION B: Grommet Base Installation
Remove screw and plate from clamp (D) as shown in diagram. Apply rubber pads (H) to the bottom
of grommet base (G) as shown in diagram. Slide cable management clip (E) and decorative cover (F)
onto pole (B). Then thread pole (B) into grommet base (G). Tighten grub screws with allen wrench (J)
as shown in diagram. Slide decorative cover (F) down. Slide grommet plate (I) onto hand crank. Insert
hand crank through grommet hole from bottom and into grommet base (G).
STEP 3
D
G
H
10-80 mm
E
F
I
J
B
If installing a TV with a VESA 300x300mm or
400x400mm pattern, attach arm (L, M) to
VESA Plate (A) with screws (N) as shown in the
diagram.
N
L
M
M
L

5
STEP 4
OPTION A: Flat Back Monitor
Attach VESA plate (A) to back of TV with screws (M-A, M-B) and washers (M-F, M-G). Make sure the two
keyholes on back have the small end facing up.
OPTION B: Curved Back Monitor
Attach VESA plate (A) to back of TV using screws (M-C, M-D, M-E), washers (M-G), and spacers (M-H,
M-I) depending on your TV’s requirements as shown in diagrams. Make sure the two keyholes on back
have the small end facing up.
M- A
M- B
M- F
M- G
M- G
M- H
M- C
M- D
M- G
M- C
M- D
M- I
M- G
M- H
M- C
M- D
M- I
M- G
M- E
M- I
M- G
M- E
M- I
M- H
M- G
M- E
M- I
M- H