WAGO 750-1405/040-000 User manual

Pos: 2/ D oku me ntati on allg em ein /Ei nb and /Ei nb and Fro nts eite -H andb uch; CI 20 17; mit Do cVaria blen (St andar d) @ 28\mod_1486477502910_0.docx@ 405388@ @ 1
Manual
WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000
16DI 24VDC 3ms XTR
16
-Channel Digital Input; 24 V DC; 3 ms; Extreme
Version 1.3.0
Pos: 3/ A ll e S er ie n ( All g em ei ne M od ul e) /Rec htl ic h es, Allg e mei n es/ I mpr e ssu m für St a nd ard h an d büc h er - al lg . A ng a be n, Ansc hr i ft en, Telef onn u m mer n und E-M ail-A dr es s e n @ 3\mod_1219151118203_21.docx @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
© 2019 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: www.wago.com
Technical Support
Phone: [phone] – 4 45 55
Fax: [phone] – 84 45 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
===Ende der Lis t e f ür Te xtm ar ke E i nb a nd_ v orn e == =

WAGO-I/O-SYSTEM 750 XTR Table of Contents 3
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 5/ D oku me ntati on allg em ein /V er zeic h ni sse /I nh alts ver z eic hni s - Ü b ersc hri ft oG u nd V er zei ch nis @ 3\mod_1219151230875_21.docx@21063 @ @ 1
Table of Contents
1Notes about this Documentation .............................................................5
1.1 Validity of this Documentation.................................................................5
1.2 Copyright................................................................................................5
1.3 Symbols .................................................................................................6
1.4 Number Notation ....................................................................................7
1.5 Font Conventions ...................................................................................7
2Important Notes ........................................................................................8
2.1 Legal Bases............................................................................................8
2.1.1 Subject to Changes............................................................................8
2.1.2 Personnel Qualifications ....................................................................8
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions.......8
2.1.4 Technical Condition of Specified Devices...........................................9
2.1.4.1 Disposal ........................................................................................9
2.1.4.1.1 Electrical and Electronic Equipment..........................................9
2.1.4.1.2 Packaging...............................................................................10
2.2 Safety Advice (Precautions) .................................................................11
3Device Description..................................................................................14
3.1 View .....................................................................................................16
3.2 Connectors...........................................................................................17
3.2.1 Data Contacts/Local Bus..................................................................17
3.2.2 Power Jumper Contacts/Field Supply ..............................................18
3.2.3 Push-in CAGE CLAMP®Connectors................................................19
3.3 Display Elements..................................................................................20
3.4Operating Elements..............................................................................20
3.5 Schematic Diagram ..............................................................................21
3.6 Technical Data .....................................................................................22
3.6.1 Device Data .....................................................................................22
3.6.2 Power Supply...................................................................................22
3.6.3 Communication................................................................................22
3.6.4 Inputs...............................................................................................23
3.6.5 Connection Type..............................................................................23
3.6.6 Mechanical Conditions .....................................................................23
3.6.7 Climatic Environmental Conditions...................................................24
3.7 Approvals .............................................................................................25
3.8 Standards and Guidelines ....................................................................26
4Process Image.........................................................................................32
5Mounting..................................................................................................33
5.1 Mounting Sequence..............................................................................33
5.2 Inserting and Removing Devices ..........................................................34
5.2.1 Inserting the I/O Module...................................................................34
5.2.2 Removing the I/O Module ................................................................35

4 Table of Contents WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
6Connect Devices .....................................................................................36
6.1 Connecting a Conductor to the Push-in CAGE CLAMP®......................36
7Use in Hazardous Environments ...........................................................37
7.1 Marking Configuration Examples ..........................................................38
7.1.1 Marking for Europe According to ATEX and IECEx..........................38
7.1.2 Marking for the United States of America (NEC) and Canada
(CEC)...............................................................................................42
7.2 Installation Regulations.........................................................................45
7.2.1 Special Notes Regarding Explosion Protection ................................45
7.2.2 Special Notes Regarding ANSI/ISA Ex ............................................47
List of Figures ..................................................................................................48
List of Tables....................................................................................................49
=== En de der Lis te für T extmar ke Verz eich nis_vor ne == =

WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 5
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 7/ All e S eri en (A llg em eine M od ul e)/ Üb ers c hri ft en/E be n e 1/H in wei s e z u dieser Do ku me ntat i on - Ü ber sc hr ift 1 @ 4\mod_1237987661750_21.docx@ 29029@ 1 @ 1
1 Notes about this Documentation
Pos: 8/ All e S eri en (A llg em eine M od ul e)/Si cher h eits- und s onstige Hinweise/Hinweis/Hinweis:D okument atio n auf bew ahr e n @ 4\mod_1237987339812_21.docx @ 29026@ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
Pos: 9/ All e S eri en (A llg em eine M od ul e)/Üb ers chr ift en/E ben e 2/ Gül tig kei tsber eic h - Üb ers c hri ft 2 @ 12\mod_1338912448776_21.docx@ 96469@ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 / S eri e 750 ( WA G O-I/ O-SYST EM )/H i nweis e z ur Do kume nt ati on ( al te Struk tur) / Gül tig keit sber ei ch/ Gül tig kei ts ber eic h D o ku ment ati on I/ O-Modul 750-xxxx, oh ne Vari anten angab e @ 14\mod_1358944037947_21.docx@ 109346@ @ 1
This documentation is only applicable to the I/O module 750-1405/040-000
(16DI 24VDC 3ms XTR).
Pos: 11 / S eri e 750 ( WA G O-I/ O-SYST EM ) /Hi n weis e z ur Do kum ent at i on ( al t e S tru k tur) /H i n weis e/ A c ht ung : H in w eis zur D o ku me nt ati o n I/ O-M od ul e 75 0- xxxx/040- 000 @ 27\mod_1468502299549_21.docx@216892@ @ 1
The I/O module 750-1405/040-000 shall only be installed and operated according
to the instructions in this manual, in the system description for the WAGO-I/O-
SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750 XTR!
In addition to these operating instructions, you will also need the system
description “Design Notes XTR – Guidelines and Recommendations for
Increasing Operational Safety” and the manual for the used fieldbus
coupler/controller, which can be downloaded at www.wago.com. There, you can
obtain important information including information on electrical isolation, system
power and supply specifications.
Pos: 12.1 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/U r heb er sc hutz -Ü ber sc hri ft 2 @ 23\mod_1435647042188_21.docx @ 184808@ 2@ 1
1.2 Copyright
Pos: 12.2 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /U rh eb ers c hutz aus führ li ch @ 4\mod_1235565145234_21.docx@ 27691@ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos:12.3/Dokumentationallgemein/Gliederungselemente/---Seit e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 12.4 / All e Seri en ( All ge mei ne M od ule) /Ü ber s c hri ft e n/ Eb ene 2/S ym bol e - Ü b er sc hri f t 2@ 13\mod_1351068042408_21.docx@ 105270@ 2 @1
1.3 Symbols
Pos: 12 .5.1 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti g e H i n weis e/ Ge fa hr/ G ef ahr : _War nu ng vor P ers on ens ch ä de n al lg e mei n _ - Er läut er ung @ 13 \mod_1343309450020_21.docx@ 101029@ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.2 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- und so ns tig e H i n weis e/ Ge fa hr/G ef a hr: _War nu ng vor P er s onen sc hä de n d urc h el e ktri sc he n S tro m_ - Erläuterung @ 13\mod_1343309694914_21.docx@ 101030@ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 12 .5.3 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/W ar nung / War n ung: _W arn u ng vor P er so nens c häd e n al lg emei n_ - Erläuterung@ 13\mod_1343309877041_21.docx@ 101035@ @1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 12 .5.4 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/V orsi c ht /V orsi ch t: _War n ung vor Per s on ens c häd en allge m ein _ - Erläuterung @ 13\mod_1343310028762_21.docx@ 101038@ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 12.5 .5 /Alle Ser ie n ( Al l ge mei ne Mod ul e)/ Si ch er h eits - u nd so ns ti ge H i n weis e/ Ac htu ng/ Ach tu ng : _ War nu ng vor Sachsc h äd en al lg e mei n_ - Erläuterung @ 13\mod_1343310134623_21.docx@ 101041@ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.6 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti ge H i nwei s e/A c htung / Ach tu ng : _ War nu ng vor Sachsc h äd en d urc h elek tros tat is ch e Aufla du ng_ - Erl äuter ung @ 13\mod_1343310227702_21.docx@ 101044@ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 12 .5.7 /Al le Seri en (AllgemeineModule)/Sicherheits- undsonstige Hin weise/Hinweis/Hinweis:_WichtigerHi nweis allgemein_ - Erläuterung@ 13\mod_1343310326906_21.docx@ 101047 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 12 .5.8 /Al le Seri en (All gemei ne Mod ule)/ Sicher heits- u nd sons ti g e H i n weis e/I nf or ma ti o n/I nf or ma ti on: _W eiter e I nf or ma ti on allg e mei n_ -Er l äu ter ung @ 13 \mod_1343310439814_21.docx@ 101051@ @ 1

WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 7
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos:12.6/Dokumentationallgemein/Gliederungselemente/---Seit e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1
Pos: 12 .7 /All e Seri en ( Al lg emei ne Mod ule) /Ü bers chr ift e n/Eb e ne 2/ D arst ell ung der Z a hle ns yste me - Ü ber s chr ift 2 @ 23\mod_1435647128078_21.docx@ 184811@ 2@ 1
1.4 Number Notation
Pos: 12.8 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /Z ahl e ns yst e me @ 3\mod_ 1221059454015_21.docx @ 21711@ @ 1
Table 1: Number Notation
Number Code
Example
Note
Decimal
100
Normal notation
Hexadecimal
0x64
C notation
Binary
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
Pos: 12.9 /All e Seri en ( Al lg e mei ne Mod ule) /Ü ber s c hri ft e n/ Eb e ne 2/ Sc hr i ft ko n venti on e n - Ü ber sc hr ift 2 @ 23\mod_1435647186005_21.docx@ 184814@ 2@ 1
1.5 Font Conventions
Pos: 12.1 0 / Al le Ser ie n (Al l ge m ein e M o dul e)/ Re ch tl ic h es, Allg e mei n es/ Sc hr if t kon ve nti on en @ 3\mod_1221059521437_21.docx @ 21714@ @ 1
Table 2: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.:
File
>
New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.:
[Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.:
[F5]
Pos: 13 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

8 Important Notes WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 14 /Al l e S eri en ( All ge mei ne M od ule) /Ü b ersc hrif te n/ Ebe ne 1/ Wic hti ge Erl äu ter unge n - Ü ber sc hr ift 1 @ 4\mod_1241428899156_21.docx @ 32170 @ 1 @ 1
2 Important Notes
Pos: 15.1 / All e Seri en ( All ge mei ne M od ule) /R ec htli ch es, Al lg em ei nes /Wi chti g e Er l äuter ung en - Einl eit u ng @ 3\mod_1221059818031_21.docx@ 21717@ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 15 .2 /All e Seri en ( All ge mei ne M od ule) /Ü bers c hrif te n/ Ebe ne 2/R ec htl ic he Grun dlag en - Über sc hr ift 2 @ 3\mod_1221060626343_21.docx @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 15.3 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /Ä nd er ung s vor beh alt - Üb erschr ift 3 und In halt @ 3\mod_1221060036484_21.docx@21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos:15.4/Serie750(WAGO-I/O-S YST EM )/ Wi c hti g e Er lä ut er u ng en ( al te Str u ktur )/ Per s on al qu al if i kati o n/ Per s on alq u ali fi ka tio n 750- xxxx - Ü bersc hrift 3 u nd Inh alt @ 3\mod_1224061208046_21.docx @ 24063@ 3@ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO-I/O-SYSTEM 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM)/ Wichti ge Erl äuter ungen (al te Str uktur )/Best imm ungsge mäß eV erwen dung/ Besti mmu ngsge mäße Ver wend ung 750- xxxx - Überschrift3@ 32\mod_1536041141528_21.docx @ 498494@ 3@ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Pos:15.6/Serie750(WAGO-I/O-S YSTEM) /Wic htige Er läut erung en (alte S tru ktur)/B estim mungsg emäß e Ver wendung /Be stim mungsg emäße V erwe ndung 7 50-xxxx für G er ät e - ST D - mitEN61000-6-3 @ 3\mod_1224064151234_21.docx@ 24070 @ @ 1
Fieldbus couplers, controllers and I/O modules found in the modular WAGO-I/O-
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to actuators or higher-level control systems. Using controllers, the signals can
also be (pre-) processed.
The devices have been developed for use in an environment that meets the IP20
protection class criteria. Protection against finger injury and solid impurities up to
12.5 mm diameter is assured; protection against water damage is not ensured.
Unless otherwise specified, operation of the devices in wet and dusty
environments is prohibited.
Operating the WAGO-I/O-SYSTEM 750 devices in home applications without
further measures is only permitted if they meet the emission limits (emissions of
interference) according to EN 61000-6-3. You will find the relevant information in
the section “Device Description” > “Standards and Guidelines” in the manual for
the used fieldbus coupler or controller.

WAGO-I/O-SYSTEM 750 XTR Important Notes 9
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Appropriate housing (per 2014/34/EU) is required when operating the
WAGO-I/O-SYSTEM 750 in hazardous environments. Please note that a
prototype test certificate must be obtained that confirms the correct installation of
the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F-I/O modules within the modular
WAGO-I/O-SYSTEM 750. Only these safe F-I/O modules ensure functional
safety in accordance with the latest international standards. WAGO's
interference-free output modules can be controlled by the safety function.
Pos: 15.7 / All e Seri en ( A llg e mei ne M o dul e)/R ec htl ich es , Al lg e mei nes /T ec hni sc her Zus ta nd d er Ger ät e - Ü bersc hrift 3 u nd Inhal t @ 3\mod_1221060446109_21.docx@ 21723@ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
• Repairs,
• Changes to the hardware or software that are not described in the
operating instructions,
• Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /Ü bers c hrif te n/E ben e 4/Entsorgen- Üb ersc hr if t 4 @ 30 \mod_1510145115652_21.docx@ 469859@ 4@ 1
2.1.4.1 Disposal
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /Ü bers c hrif te n/E ben e 5/ El ekt ro- un d El e ktr o ni kger ät e - Ü ber sc hr ift 5 @ 32\mod_1537446988068_21.docx@ 501657@ 5@ 1
2.1.4.1.1 Electrical and Electronic Equipment
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /R ech tli ch es, A llg e mein es/ Ele ktr o- u nd El e ktr oni kger ät e @ 32\mod_1532425086061_21.docx@ 491989@ @ 1
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.

10 Important Notes WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Environmentally friendly disposal benefits health and protects
the environment from harmful substances in electrical and
electronic equipment.
• Observe national and local regulations for the disposal of electrical and
electronic equipment.
• Clear any data stored on the electrical and electronic equipment.
• Remove any added battery or memory card in the electrical and
electronic equipment.
• Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
Pos: null /Doku m enta ti on allg e mei n/Gli ed er ung s el em ent e/----Leer z eil e-( 1Z) ---- @ 28\mod_1485262995837_0.docx@ 404006@ @ 1
Pos: nul l /Alle S erie n( Allg emeine M odul e)/Ü berschr ifte n/Eb ene 5/Ver pac kung - Über sc hr ift 5 @ 32\mod_1537447044202_21.docx@ 501662@ 5@ 1
2.1.4.1.2 Packaging
Pos: null /Alle S er ie n ( All gem ei ne M odul e) /R ech tli ch es, A llg e mein es/ V erp ac kung @ 32 \mod_1537446786416_21.docx@ 501653@ @ 1
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
• Observe national and local regulations for the disposal of packaging.
• Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.
Pos: 15.1 0 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel eme nt e/---Sei t enw ec hs el--- @ 3 \mod_1221108045078_0.docx @ 21810@ @ 1

WAGO-I/O-SYSTEM 750 XTR Important Notes 11
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 15.1 1 / All e S er ie n ( All ge m ein e M o dul e) /Üb er sc hr ift en /E ben e 2/Sich er hei ts hin w eis e - Ü ber s chri ft 2 @ 6\mod_1260180299987_21.docx@ 46724@ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 15.1 2 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- und sonstige Hin w eis e/Ei nlei tu ng S ic h erh eit s hin wei se H ar d war e @ 6\mod_1260180170493_21.docx @ 46720 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 15.1 3.1 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Nic ht an G erät e n unter Spa nnu ng arbei te n! @ 6\mod_1260180365327_21.docx@ 46727@ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: null /Alle S er ie n ( All gem ei ne M odul e) / Sich erh eits - und sonst ig e Hi n wei s e/G ef a hr /G ef ahr : Pr od u kt nur i n eine m g e ei gn et en Geh äus e ei n ba uen! @ 3 3\mod_1543581881435_21.docx@ 511972@ @1
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
• Guarantee that the max. permissible degree of pollution is not exceeded.
• Offer adequate protection against contact.
• Prevent fire from spreading outside of the enclosure.
• Offer adequate protection against UV irradiation.
• Guarantee mechanical stability
• Restrict access to authorized personnel and may only be opened with tools
Pos: null /Alle S er ie n ( All gem ei ne M odul e) / Sich erh eits - und sonst ig e Hi n wei s e/G ef a hr /G ef ahr : T re n n vorr ic ht ung und Ü b ers tr oms c h utz @ 3 3\mod_1543915978439_21.docx@ 512267@ @ 1
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Pos: 15.1 3. 4 / Al le Ser ien ( Allg em ein e M odul e)/Si c herh eits - und s o nsti g e H in w eis e/ G ef ahr /G ef ahr : Unfal l ver h üt ung s vor sc hr i ft en b e ach te n! @ 6\mod_1260180657000_21.docx@ 46735@ @1
Pos: 15.1 3.5 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /G ef a hr /G ef ahr: Auf nor mg erec ht e n A nsc hl uss ac ht en! @ 6\mod_1260180753479_21.docx @ 46739@ @ 1
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos: 15.1 4 / S er ie 750 ( W AG O-I/ O-SYST EM) /Wi chtig e Er l äuter ung en (alt e Str u kt ur )/ Sic her hei t s- und sonstigeHinweise/Warnung/Warnung: Speisung ausschließlich ausSELV-/PELV-Vers org ung ( 24 V-XTR -I/O-M odul e) @ 2 9\mod_1493107132163_21.docx @ 419618@ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-1405/040-000) must be powered from SELV/PELV power supply(s)!
Pos: 15.1 5 /Al le S eri en ( Allg em ein e Mo dul e)/Si ch erh eits- un d sonsti g e H in wei s e/V orsi c ht/ Vors ic ht : H ei ße Oberfl äc he nicht berü hr en! (all gemei n) @ 6\mod_1264428115588_21.docx@ 48610 @ @ 1
Do not touch hot surfaces!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM )/ Wi ch ti g e Er l äut er ung en (alt e St r u ktur ) /Sic her hei ts- u n d s on sti g e H i n w eis e/ Ac ht ung / Ac ht ung : Ein wan dfr ei e Kont a kti eru ng zur T rag s c hie n e g ew ä hrl ei st en! @ 3 4\mod_1550481407638_21.docx@ 530599@ @ 1
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos: 15.1 6.2 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- und sonstige Hin weise/A cht u ng /Ac ht u ng : D ef e kt e od er besc h ädig t e Gerät e austa usc h en! @ 6 \mod_1260180857358_21.docx@ 46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Pos: 15.1 6.3 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o ns tig e Hin wei se /A cht u ng /Ac ht u ng : G er ä te vor kriec hen de n und i soli er end en Sto ff en schüt ze n! @ 6\mod_1260181036216_21.docx@ 46747@ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Pos: 15.1 6.4 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d so nst ig e Hinw eis e /A cht u ng /Ac ht u ng : R ei nig u ng nur mit z ul äs sig e n M at er i ali en! @ 6\mod_1260181203293_21.docx@ 46751@ @ 1
Clean only with permitted materials!
Clean housing and soiled contacts with propanol.
Pos: 15.1 6.5 / All e S erie n (Al lge mei ne M o dule) /Si c her hei ts- unds onstigeHinweise/Achtung/Achtung:Kein Kontaktspray verwenden! @ 6\mod_1260181290808_21.docx @ 46755@ @1
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 15.1 6.6 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- un d s o nsti g e H i n wei se /A c ht u ng /Ac ht u ng : V er pol ung en der D ate n- un d Vers org u ng s lei t u ng en verm eid e n! @ 6\mod_1260184045744_21.docx@ 46767@ @1

WAGO-I/O-SYSTEM 750 XTR Important Notes 13
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 15.1 6.7 / All e S erie n (Al lge mei ne M o dule) /Sic h erhei ts- undsonstigeHinweise/Achtung/Achtung:ElektrostatischeEntladung v erm ei den! - DIN EN61340-5-1/-3 @ 6\mod_1260181364729_21.docx @ 46759@ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge when touched. Please observe the safety precautions
against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the
devices, please ensure that environmental factors (personnel, work space and
packaging) are properly grounded.
Pos: 15.1 7 / S er ie 750 ( W AG O-I/ O-SYST EM) /Wichti g e Erl äuter ung en ( al t e Str u kt ur ) /Sic her hei t s- u n d s on sti g e H i n weis e/ Ac ht ung / Ac ht ung : XTR - Is ola ti o nspr üf ung en mit D C durch fü hr e n! @ 1 5\mod_1370843209441_21.docx@ 122210@ @ 1
Use only direct current (DC) for insulation testing!
Both the system voltage and field voltage side are capacitively coupled to the
DIN-rail. If an I/O module is mounted on the DIN-rail, application of an AC voltage
between the DIN-rail and at least one of these two potentials can lead to the
destruction of the module.
Use only direct current (DC) for insulation testing. To avoid destroying the I/O
module, you must discharge it completely before applying the test voltage again.
Pos: 16 /D o kum e nt atio n allg emei n/ Gl ie der ung s el e me nte /---Sei t e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810 @ @ 1

14 Device Description WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 17 /A ll e Seri en (Allg e mei n e M od ul e)/ Ü b ers chr if te n/ Eb e ne 1/G erät e bes c hr ei bung - Üb er schr i f t 1@ 3\mod_1233756084656_21.docx@ 27096 @ 1@ 1
3 Device Description
Pos: 18 .1.1 /S erie 750 ( WAGO -I/O-SYST EM ) /G er ät eb es c hrei bu ng ( al t e Struktur)/Einleitung/Anwendung/DI/Anwendung750-x4xx DI @ 3\mod_1233762736718_21.docx@ 27108@ @ 1
The digital input module 750-1405/040-000 (16DI 24VDC 3ms XTR) receives
control signals from digital field (e.g. of sensors, transmitters, switches or
proximity switches).
Pos: 18 .1.2 /S erie 750 ( WAGO -I/O-SYST EM ) /G er ät eb es c hrei bu ng ( al t e Str u kt ur) /Ei nl ei t ung /I / O-B esc hr ei b ung / DI/ I /O-Beschreibung750-140x16DI 1-Lei ter Pus h-i n C AG E C LAM P @ 3\mod_1233755594906_21.docx @ 27090@ @ 1
The I/O module has 16 input channels, providing a direct connection to 1-wire
sensors.
The sensors are connected to the Push-in CAGE CLAMP®connectors
DI 1 … DI 16.
Pos: 18 .1.3 /S erie 750 ( W AG O-I/ O-SYST EM ) /G erä te b esc hrei bu ng ( al t e St r u ktur ) /Ei nl eit u ng /I/ O -B esc hr ei bu ng /A ll g e mei n /V er weis auf K api t el "An sc hl üss e" @ 8\mod_1276775378035_21.docx@57956 @ @ 1
The assignment of the connections is described in the “Connectors” section.
Pos: 18.1 .4 /D o ku men ta tio n allge mei n/ Gl ie der ung s ele men te /---Le era bs atz-( 2Z)--- @ 3\mod_1224662755687_0.docx@ 24460@ @ 1
Pos: 18 .1.5 /S erie 750 ( WAGO -I/O-SYST EM ) / Wic ht ig e Erlä ut eru ng e n ( al t e Str u ktur ) /Si c h erh ei ts- und so nstige Hinweise/Hinweis/Hinweis:DI Potential v er viel fäl tig u ng s mod ule für S en sor v ersor g ung eins etz e n @ 3\mod_1233762069125_21.docx @ 27105@ @ 1
Use field side connection modules!
Where required, use the appropriate field side connection modules for power
supply to the sensors.
Pos: 18 .1.6 /S erie 750 ( WAGO -I/O-SYST EM ) /G er ät eb es c hrei bu ng ( al t e Str u kt ur) /Ei nl ei t ung /I / O-B esc hr ei b ung / DI/ I /O-Beschreibung750-x4xx DI RC-Fi l t er 3,0 ms @ 3\mod_1233755071062_21.docx@ 27080@ @ 1
Each input channel has a RC noise rejection filter with a time constant of 3.0 ms.
Pos: 18 .1.7 /S erie 750 ( WAGO -I/O-SYST EM ) /G er ät eb es c hrei bu ng ( al t e Str u kt ur) /Ei nl ei t ung /I / O-B esc hr ei b ung / DI/ I /O-Beschreibung750-x4xxDIHSS / positivschaltend(24V) @ 3\mod_1233831724648_21.docx @ 27231@ @ 1
The I/O module inputs provide high-side switching. If the 24 V potential for field
power is switched to an input connection, the signal status for the corresponding
input channel is set to “high”.
Pos: 18 .1.8 /S erie 750 ( WAGO -I/O-SYST EM ) /G er ät eb es c hrei bu ng ( al t e Str u kt ur) /Ei nl ei t ung /L ED -A nz eig e/ LED Zust an d Si g nal @ 3\mod_1233755258578_21.docx@ 27087@ @ 1
A green LED indicates the switched status of each channel.
Pos: 18 .1.9 /S erie 750 ( WAGO -I/O-SYST EM ) /G er ät eb es c hrei bu ng ( al t e Str u kt ur) /Ei nl ei t ung /L ED -A nz ei g e/V er w ei s auf K a pi tel "Anz eig eel e ment e" @ 5\mod_1246010525000_21.docx@ 36194@ @ 1
The meaning of the LEDs is described in the “Display Elements” section.
Pos: 18.1 .1 0 / S er ie 750 ( W AG O-I/O-SY ST EM ) /G er ät ebe s chr ei b ung ( al t e Str u ktur ) / Einl eit ung / Ver s or g u ng/ Ver sor g u ng 24 V, 0 V über Leist ung s k o nt akt e Standar d @ 3\mod_1226498974531_21.docx@ 25020@ @ 1
The I/O module 750-1405/040-000 (16DI 24VDC 3ms XTR) receives the 24 V
voltage supply for the field level from an upstream I/O module or from the
fieldbus coupler/controller via blade-formed power jumper contacts. It then
provides these potentials to subsequent I/O modules via spring-formed power
jumper contacts.
Pos: 18.1 .11 / S er ie 750 ( W AG O-I/O-SY ST EM ) /Wic htig e Er l äu ter ung en (alt e Struk tur )/ Si c her heit s - u nd s ons ti ge H i n weis e/ War nu ng /W arn u ng: Speis ung aus schl i eßl ic h a us SEL V-/PELV-Ver s or g ung (24 V-XTR -I/O-M od ule) @ 29 \mod_1493107132163_21.docx @ 419618@ @ 1
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-1405/040-000) must be powered from SELV/PELV power supply(s)!
Pos: 18.1 .1 2 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic hti g e E rl äu ter ung en (alt e St ru kt ur) / Si c her hei t s- u n d s ons ti ge H i n weis e/ Ac ht ung / Ac ht ung : M a xi m aler Str om Leist u ng s kont a kt e 1 0 A @ 3\mod_1226499143500_21.docx@ 25029@ @1

WAGO-I/O-SYSTEM 750 XTR Device Description 15
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos: 18.1 .1 3 / S er ie 750 ( W AG O-I/O-SY ST EM ) /G er ät ebe s chr ei b ung ( al t e Str u ktur ) / Einl eit ung / Ver s or g u ng/ G al vani sc he Tre n nung Fel d/ S yst em @ 3\mod_1233756478750_21.d ocx @ 271 02@ @ 1
The field voltage and the system voltage are electrically isolated from each other.
Pos: 18.1 .1 4 / S er ie 750 ( W AG O-I/O-SY ST EM ) /G er ät ebe s chr ei b ung ( al t e Str u ktur ) / Einl eit ung / Ver s or g u ng/ Anor dn u ng u nt er Ber üc ksi c htig u ng der Leistungskontaktebeliebig @ 3\mod_1233756233468_21.docx@ 27099@ @ 1
With consideration of the power jumper contacts, the individual modules can be
arranged in any combination when configuring the fieldbus node.
An arrangement in groups within the group of potentials is not necessary.
Pos: 18.1 .1 5 / S er ie 750 ( W AG O-I/O-SY ST EM ) /Wic htig e Er l äu ter ung en (alt e Struk tur )/ Si c her heit s - und s onstigeHi nweise/Hinweis/Hinweis:XTR - M i sc hb etr ie b XTR/ St an dar d @ 15 \mod_1367496420828_21.docx@118326@ @ 1
Mixed operation
Mixed operation (standard/XTR modules) within a node is possible when groups
of modules are electrically isolated on the field side (i.e., electrically isolated
power supply).
Pos: 18.1 .1 6 / S er ie 750 ( W AG O-I/O-SY ST EM) /Wic hti g e E rl äu ter ung en (alt e St ru kt ur) / Si c her hei t s- un d sonstige Hin weise/Hinweis/Hinweis:XTR - E r hö ht e S t örfe s tig keit @ 1 5\mod_1367496424993_21.docx@ 118330 @ @ 1
Increased interference!
For standard-compliant application in substation instrumentation and control,
telecontrol systems, railway technology or shipbuilding certified operation,
field-side power supply filter 750-624/040-001 or power supply filter
750-626/040-000 are generally to be used for XTR module groups.
Pos: 18.1 .1 7 / S er ie 750 ( W AG O-I/O-SY ST EM ) /G er ät ebe s chr ei b ung ( al t e Str u ktur ) / Einl eit ung / Ei ns atz b erei c h/ Ei ns atz b er eic h 750- xxxx/040-0 00 all e XTR-Kop pler /C ont roll er ohne Eins c hrä nkung + Mis c hbetr ie bhi nw eise @ 1 5\mod_1368425919479_21.docx@ 119444@ @ 1
The I/O module can be operated with all fieldbus couplers/controllers of the
WAGO-I/O-SYSTEM 750 XTR.
Observe the instructions for mixed operation when used in mixed operation
behind standard fieldbus couplers/controllers.
Pos:18.2/Dokumentationall g e mei n/ Gli e der ung s el e men te /---Sei t e n wechs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

16 Device Description WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 18.3 / All e Seri en ( All ge mei ne M od ule) /Ü bers chr ift e n/ Ebe ne 2/ A nsic ht - Ü ber s chr ift 2 @ 4\mod_1240984217343_21.docx @ 31958@ 2@ 1
3.1 View
Pos: 18 .4 /Ser ie 750(WAGO-I/O-SYST EM ) / Ger äte b esc hrei bu ng ( al t e Str u kt ur) /A nsi c ht/D I/ Ans ic ht 750-140x_0040-xxxx 16 DI C AGE C L AMP @ 15\mod_1369132959936_21.docx@ 119973@ @1
Figure 1: View
Pos:18.5/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /A nsi c ht/ An s ich t P us h-in CageClamp®_LegendemitLEDs @ 15\mod_1370852562803_21.docx@ 122213@ @ 1
Table 3: Legend for Figure “View”
Pos.
Description
Details See Section
1
Marking possibility with Mini-
WSB
---
2
Status LEDs
“Device Description” > “Display Elements”
3
Data contacts
“Device Description” > “Connectors”
4
Push-in CAGE CLAMP®
connectors
“Device Description” > “Connectors”
5
Power jumper contacts
“Device Description” > “Connectors”
6
Release tab
“Mounting” > “Inserting and Removing
Devices”
Pos:18.6/Dokumentationallgemein/Gliederungselemente/---Seit e n wec hs el--- @ 3\mod_1221108045078_0.docx@ 21810@ @ 1

WAGO-I/O-SYSTEM 750 XTR Device Description 17
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 18.7 / All e Seri en ( A llg e mei ne M o dul e)/Ü ber s chri ft e n/E be ne 2/ A nsc hl üss e - Ü b ers c hri ft 2@ 4\mod_1240984262656_21.docx@31961 @ 2@ 1
3.2 Connectors
Pos:18.8/Serie750(WAGO-I/O-S YST EM )/ G er äte b esc hr ei bu ng (alt e Stru kt ur) /A nsc hlüs s e /Da te n kon ta k te /L ok alb us - Ü b ers chr if t 3 @ 6 \mod_1256294684083_21.docx @ 43660@ 3 @ 1
3.2.1 Data Contacts/Local Bus
Pos: 18 .9.1 /S erie 750 ( WAGO -I/O-SYST EM ) /G er ät eb es c hrei bu ng ( al t e Str u kt ur) /A nsc hl üs s e/ Da te n kon ta kte - Fel dbus ko ppl er /-c ontroll er und Mo dule – Ab bild ung und B eschrei bung @ 3\mod_1231771259187_21.docx@26002 @ @ 1
Communication between the fieldbus coupler/controller and the I/O modules as
well as the system supply of the I/O modules is carried out via the local bus. The
contacting for the local bus consists of 6 data contacts, which are available as
self-cleaning gold spring contacts.
Figure 2: Data Contacts
Pos: 18 .9.2 /S erie 750 ( WAGO -I/O-SYST EM ) / Wic ht ig e Erlä ut eru ng e n ( al t e Str u ktur ) /Si c h erh ei ts- undsonstigeHinweise/Achtung/Achtung:I/O-Module ni cht auf Gol dfed erkon takte leg en! @ 7\mod_1266318463636_21.docx @ 50695@ @ 1
Do not place the I/O modules on the gold spring contacts!
Do not place the I/O modules on the gold spring contacts in order to avoid soiling
or scratching!
Pos: nul l /Ser ie 750 (W AGO-I/ O-SYST EM )/ Wi ch ti g e Er l äut er ung en (alt e St r u ktur ) /Sic her hei ts- und sonstigeHin w eis e/ Ac ht ung / Ac ht ung : ESD - Au f Po te nti al aus gl eic h der U mg eb ung ac hten! @ 3 2\mod_1539077262331_21.docx@ 504433@ @ 1
Pay attention to potential equalization from the environment!
The devices are equipped with electronic components that may be destroyed by
electrostatic discharge. When handling the devices, please ensure that
environmental factors (personnel, work space and packaging) are properly
equalized. Do not touch any conducting parts, e.g., data contacts.
Pos: 18.1 0 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel eme nt e/---Sei t enw ec hs el--- @ 3 \mod_1221108045078_0.docx @ 21810@ @ 1

18 Device Description WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 18.1 1 / S er ie 750 ( W AG O-I/ O-SYST EM ) /G er ät ebe s chr ei b u ng ( alt e Stru ktur )/ A ns chl üs s e/ Lei s tu ng s kon ta kt e/ Fel d v ers org u ng - Ü ber sc hri ft 3 @ 6\mod_1256294692864_21.docx@ 43664@ 3 @ 1
3.2.2 Power Jumper Contacts/Field Supply
Pos: 18.1 2 / S er ie 750 ( W AG O-I/ O-SYST EM ) / Wic htig e Er l äu ter ung en (alt e Struk t ur) /Si c her hei t s- und sonstigeHinweise/Warnung/Warnung: Speisung ausschließlich aus SELV-/PELV-Vers or gung (24 V-XT R-I/O-M od ule) @ 2 9\mod_1493107132163_21.docx@ 419618@ @1
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this XTR I/O module
(750-1405/040-000) must be powered from SELV/PELV power supply(s)!
Pos: 18.1 3. 1 / S er ie 750 ( W AG O-I/O-SY ST EM ) /Wic htig e Er l äu ter ung en (alt e Struk tur )/ Si c her heit s - u nd s ons ti ge H i n weis e/ Vor si cht /V ors ic ht: Verl etz u ngs gef ahr dur ch schar f ka ntig e M ess er kon ta kte! @ 6\mod_1256193279401_21.docx@ 43414@ @ 1
Risk of injury due to sharp-edged blade contacts!
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent
injury. Do not touch the blade contacts.
Pos: 18.1 3. 2 / S er ie 750 ( W AG O-I/O-SY ST EM )/ G erät e be sc hr ei bung (al t e Struk tur) / An sc hl üss e/ Leis tu ng s kon ta kt e 2 LK ( M es ser /Fe d er ) - Ei nlei t ung @ 15 \mod_1371721641099_21.docx@123714@ @ 1
The I/O module 750-1405/040-000 has 2 self-cleaning power jumper contacts
that supply and transmit power for the field side. The contacts on the left side of
the I/O module are designed as blade contacts and those on the right side as
spring contacts.
Pos: 18.1 3. 3 / S er ie 750 ( W AG O-I/O- SY ST EM )/ G erät e be sc hr ei bung (al t e Struk tur) / An sc hl üss e/ Leis t ung s k on ta kte 2 L K ( Me ss er /F e d er) -A bbi l dung (16-K a nal ) @ 15\mod_1370866610582_21.docx@ 122222@ @ 1
Figure 3: Power Jumper Contacts
Pos: 18.1 3. 4 / S er ie 750 ( W AG O-I/O-SY ST EM ) /G er ät ebe s chr ei b ung ( al t e Struktur)/Anschlüsse/Leistungskontakte2LK (Messer/Feder)- L egend e @ 15\mod_1371721352500_21.docx@ 123710@ @ 1
Table 4: Legend for Figure “Power Jumper Contacts”
Contact
Type
Function
1
Spring contact
Potential transmission (Uv) for field supply
2
Spring contact
Potential transmission (0 V) for field supply
3
Blade contact
Potential feed-in (0 V) for field supply
4
Blade contact
Potential feed-in (Uv) for field supply
Pos: 18.1 3. 5 / S er ie 750 ( W AG O-I/O-SY ST EM ) /Wic htig e Er l äu ter ung en (alt e Struk tur )/ Si c her heit s - u nd s ons tig e H i n weis e/ Ac ht ung / Ac ht ung : M a xi mal er Str om L ei st u ng s kont a kt e 1 0 A @ 3\mod_1226499143500_21.docx@ 25029@ @1

WAGO-I/O-SYSTEM 750 XTR Device Description 19
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Do not exceed maximum values via power contacts!
The maximum current that can flow through the power jumper contacts is 10 A.
The power jumper contacts can be damaged and the permissible operating
temperature can be exceeded by higher current values.
When configuring the system, do not exceed the permissible maximum current
value. If there is a higher power requirement, you must use an additional supply
module to provide the field voltage.
Pos: 18.1 4 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel eme nt e/---Sei t enw ec hs el--- @ 3 \mod_1221108045078_0.docx @ 21810@ @ 1
Pos: 18.1 5 / S er ie 750 ( W AG O-I/ O-SYST EM ) /G er ät ebe s chr ei b u ng ( alt e Stru ktur )/ A ns chl üs s e/ Pu sh-in CA GECL AMP®-Ansc hlüs s e - Ü b er sc hri f t 3@ 15\mod_1370519905692_21.docx@ 122018@ 3 @ 1
3.2.3 Push-in CAGE CLAMP®Connectors
Pos: 18.1 6 / S er ie 750 ( W AG O-I/ O-SYST EM ) /G er ät ebe s chr ei b u ng ( alt e Stru ktur )/ A ns chl üs s e/D I/A nsc hl üs se 750-1 40 x 16 D I Push-in CA GECLAMP @ 3\mod_1232518694593_21.docx@ 26470@ @ 1
Figure 4: Push-in CAGE CLAMP® Connectors
Table 5: Legend for Figure “Push-in CAGE CLAMP® Connectors”
Channel
Designation
Connector
Function
1
DI 1
1
Input DI 1: Signal voltage
2
DI 2
2
Input DI 2: Signal voltage
.
.
.
15
DI 15
15
Input DI 15: Signal voltage
16
DI 16
16
Input DI 16: Signal voltage
Pos: 18.1 7 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel eme nt e/---Sei t enw ec hs el--- @ 3 \mod_1221108045078_0.docx @ 21810@ @ 1

20 Device Description WAGO-I/O-SYSTEM 750 XTR
750-1405/040-000 16DI 24VDC 3ms XTR
Manual
Version 1.3.0
Pos: 18.1 8 / Al le Ser ie n (Al l ge m ein e M o dul e)/ Üb er sc hr if t en/ Eb en e 2/Anz eig e el em e nte - Über sc hri ft 2 @ 4\mod_1240984390875_21.docx@ 31964 @ 2 @ 1
3.3 Display Elements
Pos: 18.1 9 / S er ie 750 ( W AG O-I/ O-SYST EM ) /G er ät ebe s chr ei b u ng ( alt e Stru ktur )/ A nz eig e el em e nt e/DI / A nz eig eel e ment e 750-140x16 DI @ 3\mod_1232459467390_21.docx @ 26390@ @ 1
Figure 5: Display Elements
Table 6: Legend for Figure “Display Elements”
Channel
Designation
LED
State
Function
1 State DI 1 1
Off
Input DI 1: Signal voltage (0)
Green
Input DI 1: Signal voltage (1)
2 State DI 2 2
Off
Input DI 2: Signal voltage (0)
Green
Input DI 2: Signal voltage (1)
.
.
.
15 State DI 15 15
Off
Input DI 15: Signal voltage (0)
Green
Input DI 15: Signal voltage (1)
16 State DI 16 16
Off
Input DI 16: Signal voltage (0)
Green
Input DI 16: Signal voltage (1)
Pos: 18.2 0 / Al le Ser ie n (Al l ge m ein e M o dul e)/ Üb er sc hr if t en/ Eb en e 2/Be die n ele m en te - Ü b ersc hr if t 2 @ 4\mod_1239191655456_21.docx@ 30439@ 2 @ 1
3.4 Operating Elements
Pos: 18.2 1 / S er ie 750 ( W AG O-I/ O-SYST EM ) /G er ät ebe s chr ei b u ng ( alt e Stru ktur )/ B edi en ele m e nt e/B edi e nel e me nt e I/ O-M od ul 7 5 x-xxxx nicht vor ha nde n @ 4\mod_1236322031125_21.docx @ 28063@ @ 1
The I/O module 750-1405/040-000 has no operating elements.
Pos: 18.2 2 /D o kum ent ati on al lg em ei n/Gli ed eru ng sel eme nt e/---Sei t enw ec hs el--- @ 3 \mod_1221108045078_0.doc x@ 21 810 @ @ 1