WAGO 753-647 User manual

Pos: 2 /Dokumentatio n allgemein/Einband/Ei nband Handbuch - Dec kblatt @ 9\mod_1285229289866_ 0.doc @ 64941 @ @ 1
Manual
WAGO-I/O-SYSTEM 750
DALI Multi-Master Module
753-647
Version 1.0.0
Pos: 3 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Impressum für Standar dhandbücher - allg. Anga ben, Anschriften, Telefonnummern und E-Mail-Adresse n @ 3\mod_1219151118203_2 1.doc @ 21060 @ @ 1

2 WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
© 2012 by WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: [phone] – 0
Fax: [phone] – 1 69
E-Mail: [email protected]
Web: http://www.wago.com
Technical Support
Phone: [phone] – 5 55
Fax: [phone] – 85 55
E-Mail: [email protected]
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: [email protected]
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
=== Ende der Liste für TextmarkeEinband _vorne ===

WAGO-I/O-SYSTEM 750 Table of Contents 3
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 5 /Dokumentatio n allgemein/Verzeic hnisse/Inhalts verzeichnis - ohne Gliederung - und Verzei chnis @ 3\mod_121915123 0875_21.doc @ 21063 @ @ 1
Table of Contents
1Notes about this Documentation................................................................. 5
1.1 Validity of this Documentation................................................................. 5
1.2 Copyright................................................................................................... 5
1.3 Symbols..................................................................................................... 6
1.4 Number Notation....................................................................................... 8
1.5 Font Conventions ...................................................................................... 8
2Important Notes........................................................................................... 9
2.1 Legal Bases ............................................................................................... 9
2.1.1 Subject
to Changes ............................................................................... 9
2.1.2 Personnel
Qualifications....................................................................... 9
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ...... 9
2.1.4 Technical Condition of Specified Devices......................................... 10
2.2 Safety Advice (Precautions).................................................................... 11
2.3 Requirements........................................................................................... 13
2.3.1 PC
Hardware ...................................................................................... 13
2.3.2 PC Software........................................................................................ 13
2.3.3 WAGO-I/O-SYSTEM........................................................................ 14
3Device Description ..................................................................................... 15
3.1 Device-Specific Safety Information........................................................ 15
3.2 Abbreviations and Terms ........................................................................ 16
3.3 General Description ................................................................................ 17
3.4 View ........................................................................................................ 20
3.5 Connectors............................................................................................... 21
3.5.1 Data Contacts/Internal Bus................................................................. 21
3.5.2 Power Contacts/Field Supply ............................................................. 22
3.5.3 CAGE CLAMP®Connections ........................................................... 22
3.6 Display Elements .................................................................................... 23
3.7 Operating Elements................................................................................. 24
3.8 Schematic Diagram ................................................................................. 25
3.9 Technical
Data ........................................................................................ 26
3.9.1 Device
Data ........................................................................................ 26
3.9.2 Supply................................................................................................. 26
3.9.3 Communication .................................................................................. 26
3.10 Approvals ................................................................................................ 27
3.11 Standards and Guidelines........................................................................ 27
4Process Image............................................................................................. 28
4.1 Dedicated IEC Application ..................................................................... 28
4.2 Full Mode ................................................................................................ 29
4.3 Easy Mode............................................................................................... 29
4.4 Latching Relay Function......................................................................... 30
4.4.1 Dim in 1- and 2-Button Mode ............................................................ 30
4.4.2 Process Image Overview in the "Easy" Mode.................................... 30
4.4.3 Activating/De-activating
64 DALI Actuators, Dimming................... 31
4.4.4 Activating/De-activating 16 Groups, Dimming ................................. 36
4.4.5 Activating/De-activating 16 Scenes ................................................... 36

4 Table of Contents WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
5Assembly..................................................................................................... 37
5.1 Assembly Sequence ................................................................................ 37
5.2 Inserting and Removing Devices ............................................................ 38
5.2.1 Inserting I/O Module .......................................................................... 38
5.2.2 Removing the I/O Module.................................................................. 39
5.3 I/O Modules with Pluggable Wiring Level (Series 753) ........................ 40
5.3.1 Coding ................................................................................................ 41
5.3.2 Connector Removal............................................................................ 43
6Connect Devices ......................................................................................... 44
6.1 Connecting a conductor to the CAGE CLAMP®.................................... 44
6.2 Installation Notes .................................................................................... 45
6.2.1 Module Assembly............................................................................... 45
6.2.2 Module Supply ................................................................................... 45
6.2.2.1 Power Supply Configuration for 753-620 ..................................... 46
6.2.2.2 Power Supply Configuration for 787-1007 ................................... 47
6.2.3 DALI Bus Line................................................................................... 47
6.2.4 DALI Bus Topology........................................................................... 48
7Commissioning........................................................................................... 49
7.1 Preparation .............................................................................................. 49
7.2 Accessing the DALI-Multi-Master Module............................................ 50
7.3 Module Configuration Notes................................................................... 50
7.4 Data Management Notes......................................................................... 51
7.5 Configuring the DALI Network Using the WAGO-DALI Configurator
(Basic Procedure).................................................................................... 51
8Diagnostics.................................................................................................. 53
9Use in Hazardous Environments.............................................................. 55
9.1 Marking Configuration Examples........................................................... 56
9.1.1 Marking for Europe according to CENELEC and IEC...................... 56
9.1.2 Marking for America according to NEC 500..................................... 59
9.2 Installation
Regulations........................................................................... 60
9.2.1 Special Conditions for Safe Operation of the ATEX and IEC Ex (acc.
DEMKO 08 ATEX 142851X and IECEx PTB 07.0064)................... 61
9.2.2 Special conditions for safe use (ATEX Certificate TÜV 07 ATEX
554086 X)........................................................................................... 62
9.2.3 Special conditions for safe use (IEC-Ex Certificate TUN 09.0001 X)64
9.2.4 ANSI/ISA 12.12.01 ............................................................................ 66
10 Glossary ...................................................................................................... 68
11 Appendix..................................................................................................... 71
11.1 Table Device Types in the Standard ....................................................... 71
List of Figures...................................................................................................... 72
List of Tables........................................................................................................ 73
=== Ende der Liste für TextmarkeVer zeichnis_vorne ===

WAGO-I/O-SYSTEM 750 Notes about this Documentation 5
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 7 /Alle Serien (Al lgemeine Module)/Über schriften für alle Ser ien/Hinweis zur Doku mentation/Hinweise zur Dokumentation - Überschri ft1 @ 4\ mod_1237987661750_21. doc @ 29029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /Alle Serien (Al lgemeine Module)/Hin weise zur Dokumentation/ Hinweis: Dokumentati on aufbewahren @ 4\mod_1 237987339812_21. doc @ 29026 @ @1
Keep this documentation!
The operating instructions are part of the product and shall be kept for the entire
lifetime of the device. They shall be transferred to each subsequent owner or user
of the device. Care must also be taken to ensure that any supplement to these
instructions are included, if applicable.
Pos: 9 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweise z ur Dokumentation/Gül tigkeitsbereic h Dokumentation Buskle mme75 0-xxxx, ohne Vari antenangabe @ 4\mod_123798 6650812_21.doc @ 29020 @ 2 @ 1
1.1 Validity of this Documentation
This documentation is only applicable to the I/O module 753-647
(DALI Multi-Master Module) of the WAGO-I/O-SYSTEM 750 series.
Pos: 10 /Serie 750 (W AGO-I/O-SYSTEM)/Hinweis e zur Dokumentation/ Hinweise/Achtung: Hinweiszur Dokumentation Busklemmen 750- xxxx @ 4\mod_1237986979656_ 21.doc @ 29023 @ @1
The I/O module 753-647 shall only be installed and operated according to the
instructions in this manual and in the manual for the used fieldbus
coupler/controller.
Consider power layout of the WAGO-I/O-SYSTEM 750!
In addition to these operating instructions, you will also need the manual for the
used fieldbus coupler/controller, which can be downloaded at www.wago.com.
There, you can obtain important information including information on electrical
isolation, system power and supply specifications.
Pos: 11.1 /Alle Serien ( Allgemeine Module)/Hin weise zur Dokumentati on/Urheberschutz au sführlich @ 4\mod_1235 565145234_21.doc @27691 @ 2 @ 1
1.2 Copyright
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 11.2 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

6 Notes about this Documentation WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 11.3 /Alle Serien ( Allgemeine Module)/Hin weise zur Dokumentati on/Symbole @ 3\mod_121 7394197593_21.doc @ 21010@ 2 @ 1
1.3 Symbols
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.

WAGO-I/O-SYSTEM 750 Notes about this Documentation 7
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 11.4 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

8 Notes about this Documentation WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 11.5 /Alle Serien ( Allgemeine Module)/Hin weise zur Dokumentati on/Zahlensyste me@ 3\ mod_1221059454015_21. doc @ 21711 @ 2 @ 1
1.4 Number Notation
Table 1: Number Notation
Number code Example Note
Decimal 100 Normal notation
Hexadecimal 0x64 C notation
Binary '100'
'0110.0100'
In quotation marks, nibble separated with
dots (.)
Pos: 11.6 /Alle Serien ( Allgemeine Module)/Hin weise zur Dokumentati on/Schriftkonven tionen @ 3\mod_122105952 1437_21.doc @ 21714 @ 2 @ 1
1.5 Font Conventions
Table 2: Font Conventions
Font type Indicates
italic Names of paths and data files are marked in italic-type.
e.g.: C:\Programme\WAGO-I/O-CHECK
Menu Menu items are marked in bold letters.
e.g.: Save
> A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input Designation of input or optional fields are marked in bold letters,
e.g.: Start of measurement range
“Value” Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button] Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key] Keys are marked with bold letters in square brackets.
e.g.: [F5]
Pos: 12 /Dokumentati on allgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 9
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 13 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Wichtige Erläu terungen/Wichti ge Erläuterungen - Überschr ift 1 @ 4\mod_1241428899 156_21.doc @ 32170 @ 1 @ 1
2 Important Notes
Pos: 14.1 /Alle Serien ( Allgemeine Module)/W ichtige Erläuterungen/ Einleitung Wi chtige Erläuterungen @ 3\mod_12 21059818031_21.doc @21717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 14.2 /Alle Serien ( Allgemeine Module)/Ü berschriften für alleSerien/ Wichtige Erläuterunge n/Rechtliche Grund lagen - Überschrif t 2 @3\ mod_1221060626343_21. doc @ 21726 @ 2 @ 1
2.1 Legal Bases
Pos: 14.3 /Alle Serien ( Allgemeine Module)/W ichtige Erläuterungen/ Änderungsvorbeha lt - Überschrif t3 und I nhalt @ 3\mod_12210600364 84_21.doc @ 21720 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications that serve to increase the efficiency of technical
progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from
the granting of patents or from the legal protection of utility patents. Third-party
products are always mentioned without any reference to patent rights. Thus, the
existence of such rights cannot be excluded.
Pos: 14.4 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Per sonalqualifikati on 750-xxxx @ 3\mod_122 4061208046_21.doc @ 24063 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on Series 750 devices may only be carried out by
electrical specialists with sufficient knowledge in automation. The specialists
must be familiar with the current norms and guidelines for the devices and
automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 14.5 /Serie 750 (W AGO-I/O-SYSTEM)/Wi chtige Erläuterungen/Bes timmungsgemäße Verw endung 750-xxxx @ 3\mod_1 224064151234_21.doc @ 24070@ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Couplers, controllers and I/O modules found in the modular WAGO-I/O-
SYSTEM 750 receive digital and analog signals from sensors and transmit them
to the actuators or higher-level control systems. Using programmable controllers,
the signals can also be (pre-)processed.
The components have been developed for use in an environment that meets the
IP20 protection class criteria. Protection against finger injury and solid impurities
up to 12.5 mm diameter is assured; protection against water damage is not
ensured. Unless otherwise specified, operation of the components in wet and
dusty environments is prohibited.
Operating 750 Series components in home applications without further measures
is only permitted if they meet the emission limits (emissions of interference)
according to EN 61000-6-3. You will find the relevant information in the section
on "WAGO-I/O-SYSTEM 750" "System Description" "Technical Data" in
the manual for the used fieldbus coupler/controller.

10 Important Notes WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Appropriate housing (per 94/9/EG) is required when operating the WAGO-I/O-
SYSTEM 750 in hazardous environments. Please note that a prototype test
certificate must be obtained that confirms the correct installation of the system in
a housing or switch cabinet.
Pos: 14.6 /Alle Serien ( Allgemeine Module)/W ichtige Erläuterungen/ Technischer Zustan d der Geräte - Überschri ft 3 und Inhalt @ 3\mod_122106 0446109_21.doc @ 21723 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The components to be supplied Ex Works, are equipped with hardware and
software configurations, which meet the individual application requirements.
WAGO Kontakttechnik GmbH & Co. KG will be exempted from any liability in
case of changes in hardware or software as well as to non-compliant usage of
components.
Please send your request for modified and new hardware or software
configurations directly to WAGO Kontakttechnik GmbH & Co. KG.
Pos: 14.7 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 11
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 14.8 /Alle Serien ( Allgemeine Module)/Ü berschriften für alleSerien/ Wichtige Erläuterunge n/Sicherheitshin weise - Überschri ft 2 @ 6\mod_1260180299987 _21.doc @ 46724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 14.9 /Alle Serien ( Allgemeine Module)/W ichtige Erläuterungen/ Sicherheits- und sons tige Hinweise/Ein leitung Sicherheitshi nweise Hardware @ 6\ mod_1260180170493_21.d oc @ 46720 @ @1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 14.10.1 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: Nic ht an Geräten unter Spannung ar beiten! @ 6\mod_126018 0365327_21.doc @ 46727 @ @ 1
Do not work on components while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 14.10.2 /Seri e 750 (WAGO-I/O-SYSTEM)/W ichtige Erläuterungen/ Sicherheitshin weise/Gefahr/Gefahr : Einbau 0750-xxxx nur i n Gehäusen, Schränken oder elektrischen Betriebsräu men! @ 6\mod_126018055669 2_21.doc @ 46731 @ @ 1
Installation only in appropriate housings, cabinets or in electrical operation
rooms!
The WAGO-I/O-SYSTEM 750 and its components are an open system. As such,
install the system and its components exclusively in appropriate housings,
cabinets or in electrical operation rooms. Allow access to such equipment and
fixtures to authorized, qualified staff only by means of specific keys or tools.
Pos: 14.10.3 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: Unfa llverhütungs vorschriften beachten! @6\mod_12601 80657000_21.doc @ 46735 @ @ 1
Pos: 14.10.4 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Gefahr/Gefahr: Auf normgerechtenA nschluss achten! @ 6\mod _1260180753479_21.doc @46739 @ @ 1
Pos: 14.11.1 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Def ekte oder beschädigte Ger äte austauschen! @ 6\ mod_1260180857358_21.doc @46743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts), since the long-term functionality of device/module involved can no
longer be ensured.
Pos: 14.11.2 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Ger äte vor kriechenden und i solierenden Stoffen sc hützen! @ 6\mod_126018 1036216_21.doc @ 46747 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for handling
devices/modules.
Pos: 14.11.3 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Rei nigung nur mit zulässige n Materialien! @ 6\mod_1260 181203293_21.doc @46751 @ @ 1
Cleaning only with permitted materials!
Clean soiled contacts using oil-free compressed air or with ethyl alcohol and
leather cloths.
Pos: 14.11.4 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Kei n Kontaktspray ver wenden! @ 6\mod_126018129080 8_21.doc @ 46755 @ @ 1

12 Important Notes WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Do not use any contact spray!
Do not use any contact spray. The spray may impair contact area functionality in
connection with contamination.
Pos: 14.11.5 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Ver polung vermeiden! @ 6\mod_126 0184045744_21.doc @46767 @ @ 1
Do not reverse the polarity of connection lines!
Avoid reverse polarity of data and power supply lines, as this may damage the
devices involved.
Pos: 14.11.6 /Alle Ser ien (Allgemeine Module)/ Wichtige Erläuter ungen/Sicherhei ts- und sonstige Hinweise/ Achtung/Achtung: Ele ktrostatische Entlad ung vermeiden! @ 6\mod_1 260181364729_21.doc @ 46759 @ @ 1
Avoid electrostatic discharge!
The devices are equipped with electronic components that you may destroy by
electrostatic discharge when you touch. Pay attention while handling the devices
to good grounding of the environment (persons, job and packing).
Pos: 15 /Dokumentati on allgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Important Notes 13
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 16 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Wichtige Erläu terungen/Vorausset zungen - Überschrif t2 @ 12\mod_1339753596379_21.doc @97770 @ 2 @ 1
2.3 Requirements
Pos: 17.1 /Alle Serien ( Allgemeine Module)/Ü berschriften für alleSerien/ Wichtige Erläuterunge n/PC-Hardware - Übersc hrift 3 @ 12\mod_133975 3695836_21.doc @ 97773 @ 3 @ 1
2.3.1 PC Hardware
Pos: 17.2 /Serie 759 (W AGO-Software)/WAGO-DALI -Configurator/ Tabelle: Voraussetzun gen PC-Hardware (753- 0647) @ 12\mod_1340040864 589_21.doc @ 98028 @ @ 1
Table 3: Requirements PC Hardware
Component Requirements
Operating system Windows XP/Vista/Windows 7
Random access memory (RAM) Min. 128 MB
Free hard disk storage unit Min. 1,5 MB for the WAGO DALI Configurator and 280 MB
(x86) or 610 MB (x64) for the .NET 4.0 Framework
Processor Min. 500 MHz
Other Installed network card, .NET 4.0 Framework (Redistributables
are provided), standard web browser with Java support
Pos: 17.3 /Alle Serien ( Allgemeine Module)/Ü berschriften für alleSerien/ Wichtige Erläuterunge n/PC-Software - Übersc hrift 3 @ 12\mod_133975 3791838_21.doc @ 97776 @ 3 @ 1
2.3.2 PC Software
Pos: 17.4 /Serie 759 (W AGO-Software)/WAGO-DALI -Configurator/ Tabelle: Erforder liche PC-Software (753-064 7) @ 12\mod_1340040493 236_21.doc @ 98019 @ @ 1
Table 4: Required PC Software
Component Reference Source (Order number)
WAGO-I/O-PRO WAGO (759-333)
.NET Framework 4.0 Microsoft (free download under:
www.microsoft.com)
WAGO DALI Configurator WAGO
(In WAGO-I/O-CHECK (Item No.: 759-302) starting from
version 03.04.01.09, the WAGO DALI Configurator is
integrated) or
as Stand Alone Tool free download under:
www.wago.com)
Pos: 17.5 /Serie 759 (W AGO-Software)/WAGO-DALI -Configurator/ Tabelle: Optionale PC- Software (753-0647) @ 12\ mod_1340040591285_21. doc @ 98022 @ @1
Table 5: Optional PC Software
Component Reference Source (Order number)
WAGO-I/O-CHECK
(from version 03.04.01.09)
WAGO (759-302)
WAGO Ethernet Settings WAGO (free download under:
www.wago.com)
Recommendation: WAGO-I/O-CHECK!
Note, that for an easy installation and configuration of the DALI Multi-Master
Module 753-647 the commissioning tool WAGO-I/O-CHECK is recommended!
Pos: 17.6 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

14 Important Notes WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 17.7 /Alle Serien ( Allgemeine Module)/Ü berschriften für alleSerien/ Wichtige Erläuterunge n/WAGO-I/O-SYSTE M- Überschrift 3 @ 13\mod_134277942258 4_21.doc @ 100660 @ 3 @ 1
2.3.3 WAGO-I/O-SYSTEM
Pos: 17.8 /Serie 759 (W AGO-Software)/WAGO-DALI -Configurator/ Tabelle: Erforder liche Komponenten des WA GO-I/O-SYSTEMs (753-0647) @12\mod_13400 40395421_21.doc @ 98016 @ @ 1
Table 6: Required Hardware of the WAGO-I/O-SYSTEM
Component Reference Source (Order number)
Fieldbus controller/PLC
WAGO-I/O-SYSTEM 750
e. g. ETHERNET PLC 750-881
WAGO (750-881)
DALI Multi-Master Module
753-647
WAGO (753-647)
End Module 750-600 WAGO (750-600)
Current supply for the indirect
supply of the DALI Bus
participants via the DALI Multi-
Master Module 753-647, e. g.:
DC/DC Converter 753-620 or
Current supply 787-1007
WAGO (753-620)
WAGO (787-1007)
Pos: 18 /Dokumentati on allgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 15
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 19 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Gerätebeschrei bung/Gerätebesc hreibung - Überschrif t 1 @ 3\mod_1233756084656_21. doc @ 27096 @ 1 @ 1
3 Device Description
Pos: 20.1 /Serie 753 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/753-0647/ Gerätespezifisc he Sicherheitshin weise @ 12\mod_13320755426 98_21.doc @ 91390 @ 2 @ 1
3.1 Device-Specific Safety Information
Required accessories: Power supply unit for indirect power supply via the
DALI-Multi-Master module 753-647, Item No.: 753-620 or 787-1007!
Please note that a suitable power supply is required for the network slaves via the
DALI Multi-Master module, such as the power supply unit for the DALI Multi-
Master module 753-647, Item No.: 787-1007, or the DC/DC converter 753-620.
These power supplies do not provide direct power to the DALI bus, but only
indirect power supply via the DALI Multi-Master module. They ensure electrical
isolation for this between the DALI bus and the I/O module required for the
installation of 230V electrical loads.
DALI slaves can be destroyed on misuse of the 787-1007 power supply unit!
The WAGO power supply (Item No.: 787-1007) may only be connected to the
DALI Multi-Master module. Never connect this power supply directly to the
DALI network without a DALI Multi-Master module connected between the
power supply and the network, as a direct connection to the DALI bus can result
in the destruction of the DALI slaves connected to the system!
Power supply for the DALI bus is provided indirectly via the DALI Multi-Master
module.
No reverse voltage protection!
The module is not protected against incorrect connection of the connecting leads.
Perform configuration using the WAGO DALI Configurator!
You must use the WAGO DALI Configurator for configuration of the DALI
Multi-Master module 753-647 and the DALI Line.
The WAGO DALI Configurator is integrated into the WAGO-I/O-CHECK
commissioning tool (Item No.: 759-302) starting from Version 03.04.01.09, or
you can download the WAGO DALI Configurator free of charge as a stand-alone
tool from the WAGO Internet site at:
www.wago.com

16 Device Description WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
More information about the WAGO DALI Configurator!
A detailed description of the WAGO DALI Configurator is given in the manual
for the configurator.
You can download this manual free of charge from the WAGO Internet site at:
www.wago.com
Pos: 20.2 /Serie 753 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/753-0647/A bkürzungen und Bezeic hnungen - DALI-spezif isch @ 12\mod_133283804 6742_21.doc @ 92190 @ 2 @ 1
3.2 Abbreviations and Terms
Table 7: Abbreviations and terms used in this manual
Abbreviation/
Term Explanation
Control Device IEC term for the DALI (Multi)-Master (also, active sensors)
Control Gear IEC term for passive electronic ballast (actuators)
DALI "Digital Addressable Lighting Interface"
(protocol for lighting control)
ECG Electronic control gear (ballast unit)
PI Process image of I/O module
PAA I/O module output process data
PAE I/O module input process data
More definitions of terms given in the glossary.
Further, detailed explanations and definitions of technical terms used in this
manual are given in alphabetical order in the Section "Glossary."
Pos: 20.3 /Dokumentatio n allgemein/Glieder ungselemente/---Seitenwechsel--- @ 3\mod_1221108045078_0.doc @ 21810 @ @ 1

WAGO-I/O-SYSTEM 750 Device Description 17
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 20.4 /Alle Serien ( Allgemeine Module)/Ü berschriften für alleSerien/ Gerätebeschreibung/ Allgemeine Beschr eibung - Überschrif t 2 @ 12\mod_1339156939064_ 21.doc @ 96837 @ 2 @ 1
3.3 General Description
Pos: 20.5 /Serie 753 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/753-0647/B usklemmenbeschr eibung 753-0647 @ 11\mod_1328 102787607_21.doc @87383 @ @ 1
The DALI Multi-Master module is used to connect a DALI network (DALI Line)
to a WAGO fieldbus node with PLCs and 750/753 Series I/O modules.
This module is used in applications for digital control of lighting actuators, such
as control gear (electronic ballasts) in building automation and for evaluation of
DALI sensors.
DALI enables complex lighting scenes to be implemented with group functions.
Using the WAGO-I/O-SYSTEM, DALI control devices are seamlessly integrated
with all supported BA and fieldbus protocols.
Figure 1: Overview of DALI network with a WAGO I/O SYSTEM 750
The 753-647 DALI Multi-Master module complies with the DALI standard
according to IEC 62386. This manufacturer-independent protocol ensures
interoperability of DALI devices in lighting applications.
This module is designed so as to allow future-oriented adaptation to the current
DALI standard by simple updating using a firmware update via the ETHERNET
fieldbus and PC software.
Two options are available for power supply for the DALI Multi-Master module;
via the 753-620 DC/DC converter, which provides power for one DALI Multi-
Master module from the 24 V system power supply, or via the 787-1007 230 V
primary switch mode power supply unit for parallel supply of several DALI
Multi-Master modes (see Section "Power Supply").

18 Device Description WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
The DALI Multi-Master module supplies bus power of 200 mA for power supply
of any number of DAL bus slaves per line.
The maximum number of bus slaves depends on the sum current consumption of
the specific devices and the address range for the actuators and sensors.
The module is equipped with two connections for the bus line (+DALI and -
DALI) for connection of the DALI bus (DALI line).
The bus line is installed in free topology. Ring-shaped links are prohibited.
As the length of the line of a bus line is limited and as the maximum line lengths
between the bus devices may not be exceeded, general DALI guidelines must be
observed (see Section "Installation Notes").
The module supports a total of 64 addresses for control gear (ECGs) and 64
addresses for control devices (DALI sensors). You can select from several
addressing methods for this.
After successful address allocation, 16 groups and 16 scenes can be assigned to
each of the DAL ECGs. A further 16 virtual groups can also be configured on the
DALI bus.
The WAGO-I/O-PRO programming software is used to program the fieldbus
nodes.
An extensive IEC-61131-3 library is available with simple modules for
implementing complex lighting applications.
The WAGO-I/O-CHECK commissioning tool can be used for configuration of the
fieldbus nodes.
The free WAGO-DALI Configurator can be used for simple commissioning and
maintenance and for easy configuration of the DALI Multi-Master module and the
interconnected DALI line.
You can call up the Configurator directly from WAGO-I/O-CHECK when the
commissioning tool is available. The WAGO-DALI Configurator can also be used
as a stand-alone tool.
More information about the WAGO DALI Configurator!
The WAGO-DALI Configurator is integrated into the WAGO-I/O-CHECK
commissioning tool (Item No.: 759-302) starting from Version 03.04.01.09, or
you can download the WAGO-DALI Configurator free of charge as a stand-alone
tool from the WAGO Internet site at:
www.wago.com.

WAGO-I/O-SYSTEM 750 Device Description 19
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
More information about WAGO-I/O-PRO and WAGO-I/O-CHECK!
You can order the WAGO software under the following item numbers:
- WAGO-I/O-PRO programming tool (Item No.: 759-333) and
- WAGO-I/O-CHECK commissioning tool (Item No.: 759-302;
with the WAGO-DALI Configurator integrated starting from Version
03.04.01.09).
You can download the manuals for these software tools free of charge from the
WAGO Internet site at:
www.wago.com
The DALI Multi-Master module can be operated in two different modes.
• Full Mode
• Easy Mode
In the Full mode, acyclic data transfer with the PLC is implemented using a
mailbox interface via a acyclic transmission channels (see Section "Process
Image" / "Full Mode").
As mentioned above, an Easy mode is also available which enables lighting
control using simple binary signals without any complicated PLC programming
(see Section "Process Image" / "Easy Mode").
The Easy mode is the standard state for the DALI Multi-Master module. The Full
mode can be activated via PLC modules, or using the WAGO-I/O-CHECK
software.
Eight colored LEDs on the I/O module enclosure signal active and inactive
operating modes, data transfer via DAL and the data bus, application of DALI bus
power and internal statuses or errors of the I/O module (see Section "Display
Elements").
Pos: 20.6 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/LED-Anzei ge/LED Zustand Betri eb, Klemmenbus-Kommu nikation und Signalüb ertragung @ 6\mod_12579236 57453_21.doc @ 44269 @ @ 1
Multi-color LEDs indicate the operating status and the trouble-free internal bus
communication as well as the status of the signal transmission.
Pos: 20.7 /Serie 750 (W AGO-I/O-SYSTEM)/Gerä tebeschreibung/Besc hreibung/Einsatzber eich/Einsatz an Fe ldbuskopplern und Feldb uscontrollern des W AGO-I/O-SYSTEMS (753-648) @ 12\ mod_1339944827014_21. doc @ 97910 @ @ 1
The I/O module 753-647 can be used with fieldbus couplers and fieldbus
controllers of the WAGO-I/O-SYSTEM 750.
Pos: 21 /Dokumentati on allgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1

20 Device Description WAGO-I/O-SYSTEM 750
753-647 DALI Multi-Master Module
Manual
Version 1.0.0
Pos: 22 /Alle Serien ( Allgemeine Module)/Über schriften für alle Seri en/Gerätebeschrei bung/Ansicht - Übersc hrift 2 @ 4\mod_124098 4217343_21.doc @ 31958 @ 2 @ 1
3.4 View
Pos: 23 /Serie 753 (W AGO-I/O-SYSTEM)/Geräteb eschreibung/Ansic ht/Sonderklemmen/An sicht 753-0647 @ 11\mod _1328521741573_21 .doc @ 87735 @ @1
Figure 2: View
Table 8: Legend for „View“ figure
Pos. Marking Meaning For details see Section
1 ---
Marking options using the
Mini-WSB ---
2 A … H Status LEDs „Device Description“ >
„Display Elements“
3 --- Data contacts „Device Description“ >
„Connections“
4 1, 5
CAGE CLAMP® Connections
DALI +
„Device Description“ >
„Connections“
5 ---
Release tab for bus module
and plug
"Mounting" > "Insert and
Removing Device"
6 2, 6
CAGE CLAMP®Connections
DALI -
„Device Description“ >
„Connections“
7 3, 7
CAGE CLAMP® Connections
DC 18 V DALI supply
„Device Description“ >
„Connections“
8 4, 8
CAGE CLAMP® Connections
ground DALI supply
„Device Description“ >
„Connections“
Pos: 24 /Dokumentati on allgemein/Glieder ungselemente/---Seitenwechsel---@ 3\mod_1221108045 078_0.doc @ 21810 @ @ 1