Wallbeds Australia AB-2a User manual

AB-2a- Cabinet Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are placed
on the “back” or underside of the cabinet and will not be seen once assembled.
AB-2a Cabinetry Panels
1
End Panel Back Panel Door Panel End Panel
Top Panel
Kick Panel
Fixed Shelf
Bottom Panel
©2019 WallBeds Australia

Cam Pins - Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
Cam Lock Cam Pin
Door Hinge Clip
Small Handle Handle Fixing Screw
Door Hinge
AB-2a Hardware Parts
Back Bottom Top
Rail/Kick
Bottom Top
NOTE: In the Top and
Bottom Panels Insert the
cam pins on the opposite
side to the Cam Lock.
Step 1– Inserting Cabinetry Hardware
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
2
Fixed Shelf
End End
©2019 WallBeds Australia

3
Attach the Hinge Clips before assembling the cabinetry.
Door Hinge Clips -
Line up the Hinge Clip with the pre-drilled holes in the End Panel. Ensure that the arrow on
the Hinge Clip is pointing towards the edge tape. Fix these by tapping them in gently with a
hammer, then tightening the screws. Refer to image 3 page 5
Step 2 – Cabinet Assembly
Start the cabinet assembly by using either one of the End Panels
Back Panel - With the cam locks facing away from the inside, place the cabinet back panel onto
the side panel. Match up the cam locks with the cam pins. Tighten the cam locks and cam pins
together by using a Phillips Head hand screwdriver.
Bottom and Top Panels - With the cam locks facing away from the inside of the cabinet attach
these panels to the end panel and back panel. Refer to images 1 & 2 page 5
Kick Panel - With the cam locks facing to the inside of the cabinet attach this panel to the end
panel.
•Place the remaining end panel over the top of the previously assembled panels. Ensuring the
cam pins are lined up with the cam locks. Tighten the cam pins to the cam locks.
Note: You may need to lightly tap the cam pins into the cam locks with a rubber mallet. Ensure
you do this where the cam pins are. Failure to do so may result in damage.
Once assembled, stand the cabinet up to fit the fixed shelving.
Fixed Shelves – Place the Cam Locks over the previously installed Cam Pins. Then tighten the
Cam Pins using a Phillips Head hand screwdriver.
Step 3 – Fitting the Door Hinges and Door Panel
Before attaching the door panel, place the cabinet next to the side of the wall bed that it will be
attached too.
Do not make the end panel of the cabinet flush with the end panel of the wall bed.
Door Hinges -
Place the cup part of the hinge into the cupboard door panel, ensuring that the arm of the hinge
is facing out of the door panel. Once in the position close the hinged flap, this will secure them
into place. There are no screws required to attach these hinges. Refer to images 4, 5 & 6 page 5
Attaching the Door to the Cabinet – Insert the hinge prongs on the hinge arms into the hinge
clip. Once inserted press the back of the hinge arm until you hear it click into place. Refer to
image 7 page 5
•Once the door is attached, check that the cabinet door panel is flush with the front edge of
the end panel of the wall bed.
©2019 WallBeds Australia

Removing Panel Stickers/Labels
To remove once installed, heat up with hair dryer & then to remove any sticky residue
use wax and grease remover or similar.
Avoid using a razor blade as you may damage the cabinetry.
4
Step 4 Attaching the Cabinet to your wall bed
To attach the cabinet to the wall bed you will need to pre-drill four 5mm pilot holes. These holes
will be covered using the FastCaps supplied.
IMPORTANT - When pre-drilling the wood screw pilot holes use caution not to go all the way
through to the end panel of the wall bed.
•Temporarily fasten the cabinets together with clamps. Pre-drill a total of four 5mm pilot
holes in the end panel of the cabinet — two towards the top of the unit and two at the
bottom. Attach the cabinet to the wall bed using the 28mm screws supplied. Then remove
the clamps.
Caution: Do Not over tighten the wood screws into the side of the cabinet End Panel as it may
end up protruding through the opposite side of the panel.
Attaching Door Handle -
Place the handle over the pre-drilled holes in the door panel. Insert the handle screws through
the pre-drilled holes in the door panel and tighten using a Phillips head screwdriver.
IMPORTANT SAFETY INFORMATION
All WallBeds Australia Bookcases and Cabinets must be securely attached
to the WallBed before use. Ensure that children DO NOT climb or hang on any part
of the Bookcase or Cabinet.
Failure to do so may result in personal injury.
©2019 WallBeds Australia

Image 3
Image 2
Image 1
Image 4
Image 5 Image 6 Image 7
5
©2019 WallBeds Australia