Wallbeds Australia AB-6 User manual

Important Safety Advice Sheet
PLEASE READ BEFORE YOU BEGIN:
•Please read and understand the instructions prior to assembly.
Incorrect installation of this product could possibly result in
personal injury or physical damage.
•WallBeds Australia recommends two people to safely assemble
and install the wall bed - It is not recommended you try to install
this bed on your own.
•The wall bed MUST be securely fastened to the wall. Failure to do
so will cause the bed to tip over & may cause damage to the
cabinet or serious personal injury.
•All additional cabintery must be securely fasten to the Wall Bed
cabinet.
•Whilst these products are DIY it is recommended the wall bed be
installed by a qualified trades person if you are not comfortable
with the installation of this product.
WallBeds Australia is not responsible for any damages
or injuries incurred by incorrect installation of this
product.
1
©2019 WallBeds Australia

AB-6 Cupboard & Drawer Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the “back” or underside of the cabinet and will not be seen once assembled.
End Left
Cupboard Door
End Right
Back
Bottom Panel
Top Panel
AB-6 Pull Out / Drawer Table Cabinetry Panels
Drawer Front Drawer / Table Bottom
Kick
2
©2019 WallBeds Australia

AB-6 Hardware Parts
Small Handle Drawer Clip
Pull Out Drawer/Table Runners
Handle Fixing Screw Door Hinge Door Hinge Clip
Euro Screw Cam Lock Cam Pin
Done Head Screw 28mm Wood Screw
3
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
Back Bottom Top
Rail
Step 1 – Inserting Cabinetry Hardware
©2019 WallBeds Australia

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
End End
Drw Bot
Bottom
Top
NOTE: In the
Bottom Panel Insert
the cam pins on the
opposite side to the
Cam Lock.
Pull Out Drawer / Table Runners –
Attach the runners before assembling the cabinetry.
Turn the drawer runner over to view from the back.
•Detach the drawer slide from the main sliding runner by pulling the clip as
indicated by the arrow on the clip. Line up the three holes in the metal runner with
the pre-drilled holes in the End Panel. Attach these runners using the Euro screws.
Do this for both End Panels DO NOT re-insert the drawer slide at this stage. Refer
to images 1 & 2 page 9
Door Hinge Clips –
Attach the Hinge Clips before assembling the cabinetry.
With the arrow indicator on the hinge block facing to the front edge of the panel.
•Line up the Hinge Plate with the pre-drilled holes in the End Panel. Fix these by tapping
them in gently with a hammer, then tightening the screws. Refer to image 6 page 10
NOTE: In the Top
Panel Insert the cam
pins on the same
side as the Cam
Lock
4
Drawer Clips –
Insert these into the drawer front ensuring the up & down arrows on the drawer clips are facing
the outside edge of the drawer panel. Fix these into the drawer front by tapping them in gently
with a hammer. Refer to image 10 page 10
©2019 WallBeds Australia

Cupboard Door Hinges –
Place the cup part of the hinge into the cupboard door panel ensuring that the arm of the hinge is
facing out of the door panel. Once in the position close the hinge flap, this will secure them into
place. There are no screws required to attach these hinges. Refer to images 4 & 5 page 5
Step 2 – Cupboard & Pullout Drawer / Table Cabinet Assembly
Start the cabinet assembly by using either one of the cabinet End Panels.
Cabinet Back Panel - Ensuring the cam locks are facing away from the inside. Place the cabinet back
panel onto the side panel. Match up the cam locks with the cam pins. Tighten the cam locks and
cam pins together by using a Philips head hand screwdriver.
Cabinet Bottom Panel - With the cam locks facing away from the inside of the cabinet attach the
bottom panel to the end panel and back panel. Refer to image 7 page 10
Cabinet Top Panel - With the cam locks facing the inside of the cabinet attach the top panel to the
end panel and back panel. - It is essential that the cam locks are facing the inside of the cabinet.
Cabinet Kick / Rail - With the cam locks facing to the back of the cabinet attach the kick panel to the
end panel.
Place the remaining end panel on top of the previously assembled panels. Ensuring the cam pins are
lined up with the cam locks. Tighten the cam pins to the cam locks.
Pull Out Drawer / Table - Using the dome head screws, attach the pullout drawer/table runners to
the drawer/table panel The holes for these are pre-drilled. Refer to image 3 page 9
Pull Out Drawer / Table Front - Attach the Pull Out Drawer / Table to the front panel by tightening
the cam pins into the cam locks.
Cupboard Door - With the hinge arms facing into the cabinet line up the prongs on the door hinges
with the hinge clips. Push the door so these clips are all the way in and then push the back of the
hinge arm until you hear it click into position. Refer to image 8 page 10
Place the Cupboard & Drawer unit next to the side of the Alpha Wallbed that it will be attached to.
Ensure the front edge of the drawer & cupboard is flush with the front edge of the wall bed cabinet.
5
Attaching the handles
Place the handle over the pre-drilled holes in the door and drawer fronts panels. Insert the handle
screws through the pre-drilled holes in the door panel and tighten using a Phillips head screw driver.
©2019 WallBeds Australia

AB-6 Bookcase Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Bottom Panel
Top Panel
AB-6 Bookcase Cabinetry Panels
Back Panel
6
©2019 WallBeds Australia

Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
Back Panel Bottom Panel Top Panel
Step 1 – Inserting Bookcase Cabinetry Hardware
Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
End Panel End Panel Bottom Panel
Top Panel
NOTE: In the Bottom Panel Insert the cam
pins on the opposite side to the Cam Lock.
NOTE: In the Top Panel Insert the cam pins
on the opposite side as the Cam Lock
7
©2019 WallBeds Australia

Step 2 – Bookcase Cabinet Assembly
Start the cabinet assembly by using either one of the cabinet End Panels.
Back Panel - With the cam locks are facing away from the inside. Place the cabinet back panel onto
the side panel. Match up the cam locks with the cam pins. Tighten the cam locks and cam pins
together by using a Philips head hand screwdriver.
Top & Bottom Panels - With the cam locks facing away from the inside of the Bookcase attach the
Bottom Panel to the End Panel and Back Panel. Repeat this process with the Top Panel.
Place the remaining End Panel on top of the previously assembled panels. Ensuring the cam pins are
lined up with the cam locks. Tighten the cam pins to the cam locks.
Tip: You may need to lightly tap the cam pins into the cam locks with a rubber mallet. Ensure you
do this where the cam pins are. Failure to do so may result in damage to the End Panel.
8
Step 3 – Fixing both Units together and to the Wall Bed
•Place the bookshelf unit on top of the drawer cabinet unit and line up the front of the bookcase
bottom panel with the front edge of the drawer. Refer to images 13 & 14 page 11
•Check that the bookshelf end panel is also flush with the front edge of the wall bed cabinet end
panel.
IMPORTANT: Use caution not to go all the way through the opposite sides of the panels when
drilling the pilot holes for the 28mm wood screws.
Do Not over tighten the wood screws into the side of the wall bed End Panel or bottom of the top
cabinet as it may end up protruding through the opposite side of the panel.
Attaching the Cabinet to the WallBed -Using an existing shelf pin hole, re-drill a 5mm pilot to fix
the bookshelf to the side of the wall bed cabinet by using the 28mm wood screws supplied. Do
two towards the top and two towards the bottom of the unit.
Attaching the Cupboard & Drawer to the Cabinet -Remove the drawer & pre-drill a 5mm pilot hole
up through the top panel of the drawer unit into the bottom panel of the bookshelf. Do one
towards the front and then one towards the back of the unit. Attach together using the 28mm
screws supplied.
Removing Panel Stickers/Labels
To remove once installed, heat up with hair dryer & then to remove any sticky residue
use wax and grease remover or similar.
Avoid using a razor blade as you may damage the cabinetry.
IMPORTANT SAFETY INFORMATION
All WallBeds Australia Bookcases and Cabinets must be securely attached to the WallBed before
use. Ensure that children DO NOT climb or hang on any part of the Bookcase or Cabinet.
Failure to do so may result in personal injury.
Insert the shelf pins into the shelf pin holes at the desired height for your shelves. If you find it’s too
high or too low, adjust the shelf by moving the supports to the holes at the required height.
©2019 WallBeds Australia

9
Image 1
Image 2
Image 4 Image 5
Image 3
©2019 WallBeds Australia

10
Image 6Image 7
Image 9
Image 8
Image 10
©2019 WallBeds Australia