Wallbeds Australia AB-4a User manual

Important Safety Advice Sheet
PLEASE READ BEFORE YOU BEGIN:
•Please read and understand the instructions prior to assembly.
Incorrect installation of this product could possibly result in
personal injury or physical damage.
•WallBeds Australia recommends two people to safely assemble
and install the wall bed - It is not recommended you try to install
this bed on your own.
•The wall bed MUST be securely fastened to the wall prior to use.
Failure to do so will cause the bed to tip over & may cause
damage to the cabinet or serious personal injury.
•All additional cabinetry must be securely fasten to the Wall Bed
cabinet.
•Whilst these products are DIY it is recommended the wall bed be
installed by a qualified trades person if you are not comfortable
with the installation of this product.
WallBeds Australia is not responsible for any damages
or injuries incurred by incorrect installation of this
product.
1
©2019 WallBeds Australia

AB-4aAssembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number.
Prior to assembly, separate and group all matching panels numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the units
have been built, as these will assist with assembly. Most of the stickers are placed
on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Back
Kick / Rail
Bottom Panel
Top Panel
AB-4a Drawer Unit Panels
Drawer Front
Drawer Bottom
Drawer Back
2
©2019 WallBeds Australia

AB-4a Drawer Unit Hardware
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
Back Panel Bottom Panel Top Panel
Rail / Kick Drw Back
Step 1– Inserting Drawer Unit Hardware
3
Small Handle Drawer Clip
Handle Fixing Screw
Euro Screw Cam Lock
Cam Pin
Done Head Screw
28mm Wood Screw
Drawer Runners &
Metal Drawer Sides
©2019 WallBeds Australia

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
Drw Bot
Bottom Panel
Top Panel
NOTE: In the
Bottom Panel Insert
the cam pins on the
opposite side to the
Cam Lock.
Drawer Runners –
Attach the runners prior to assembling the cabinetry.
Drawer Clips –
NOTE: In the Top
Panel Insert the cam
pins on the same
side as the Cam
Lock
4
©2019 WallBeds Australia
Insert these into the drawer front, ensuring the up & down arrows on the drawer clips are
facing the outside edge of the drawer panel. Fix these into the drawer front by tapping
them in gently with a hammer - Refer to image 10 page 11
Line up the holes in the metal runner with the pre-drilled holes in the End Panel.
Attach these runners using the Euro screws. Do this for both End Panels- Refer to
images 1 & 2 page 10
End
Left
End
Right

5
Step 2 Ab-4a Drawer Unit Assembly
Start the cabinet assembly by using either one of the End Panels.
Back Panel - Ensuring the cam locks are facing away from the inside. Place the cabinet back
panel onto the side panel. Match up the cam locks with the cam pins. Tighten the cam locks
and cam pins together by using a Phillips head hand screwdriver.
Bottom Panel - With the cam locks facing away from the inside of the cabinet attach the
bottom panel to the end panel and back panel. Refer to images 6&7 page 11
Top Panel - With the cam locks facing the inside of the cabinet attach the bottom panel to
the end panel and back panel. - Ensure the cam locks are facing the inside of the cabinet.
Kick / Rail Panel - With the cam locks facing to the back of the cabinet attach the kick panel
to the end panel.
Place the remaining end panel on top of the previously assembled panels. Ensuring the cam
pins are lined up with the cam locks. Tighten the cam pins to the cam locks.
Metal Side Drawer Assembly
Note – There are no guide holes on the underside of the drawer bottom panel for the metal
drawer sides. The dome head screws supplied do not require these holes to be pre-drilled.
Drawer Back Panel to Drawer Bottom Panel - With the cam locks facing the back attach the
drawer bottom panel to the drawer back panel. Tighten cam locks to cam pins. Refer to
image 4 page 10
Metal Drawer sides - Attach the metal drawer sides to the drawer bottom and drawer back
panels using the dome head screws. Refer to images 3&4 page 10. Place assembled drawer
into the drawer unit.
DO NOT ATTACH DRAWER FRONTS UNLESS THE DRAWERS ARE IN THE CABINET.
Attaching Drawer Fronts – To ensure the drawer front is the correct way up. Place drawer
front on to the drawer clips -DO NOT PUSH DRAWER FRONT FULLY ONTO THE DRAWER
CLIPS. Refer to images 8&9 page 12
Starting with the top drawer, gently close the drawer ensuring the top edge of the drawer
is level with the top panel or drawer front above. If the drawer front is higher than the
panel, remove it from the drawer clips and turn the drawer front up the opposite way.
Double-check the drawer front is now level with the cabinet top panel.
Once the drawer front is the correct way up, push the drawer front into the metal sides of
the drawer until you hear the drawer click into place on both sides. Tighten the screws on
the outside of the drawer clips using a Phillips head hand screwdriver. Refer to images
14&15 page 12
©2019 WallBeds Australia

AB-4a Upper Cabinet Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Bottom Panel
Top Panel
AB-4a Cabinetry Panels
Back Panel
6
Adjustable Shelf
Door Panel
©2019 WallBeds Australia

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
Cam Lock Cam Pin
Door Hinge Clip
Small Handle Handle Fixing Screw
Door Hinge
Shelf Pin
AB-4a Cabinet Hardware Parts
Back Bottom Top
End End
Bottom Top
NOTE: In both the Top and
Bottom Panels Insert the cam
pins on the opposite side to
the Cam Lock.
Step 1– Inserting Cabinetry Hardware
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
7
28mm Wood Screw
©2019 WallBeds Australia

8
Door Hinge Clips –
Attach the Hinge Plates before assembling the cabinetry.
With the arrow indicator on the hinge block facing to the front edge of the panel. Line up the
Hinge Plate with the pre-drilled holes in the End Panel. Fix these by tapping them in gently with
a hammer, then tightening the screws. Refer to image 10 page 10
Step 2 – Cabinet Assembly
Start the cabinetry assembly by using either one of the End Panels
Back Panel - Ensuring the cam locks are facing away from the inside. Place the cabinet back panel
onto the end panel. Match up the cam locks with the cam pins. Tighten the cam locks and cam
pins together by using a Phillips head hand screwdriver.
Bottom & Top Panels - With the cam locks facing away from the inside of the cabinet attach the
bottom & top panels to the back panel. Refer to images 11 & 12 page 11
Place the remaining end panel over the above assembled panels. Ensuring the cam pins are lined
up with the cam locks. Tighten the cam pins to the cam locks.
•Note: You may need to lightly tap the cam pins into the cam locks with a rubber mallet. Ensure
you do this where the cam pins are located. Failure to do so may result in damage to the End
Panel.
Place the Drawer unit next to the side of the Alpha Wallbed that it will be attached to. Ensure the
front edge of the drawers are flush with the front edge of the wall bed cabinet.
Prior to attaching the door panel. Place the upper cabinet on top of the Drawer Unit and line up the
front edge of the bottom panel with the front of the drawer on the Drawer unit.
•NOTE: This will leave the Front Edge of the End Panel of this cabinet approximately 18mm back
from the Front Edge of the wall bed End Panel. This will allow for the Door Panel to be flush with
the wall bed End Panel.
Step 3 – Placing both Units to the Alpha Wall Bed
©2019 WallBeds Australia
Attaching the Drawer Unit to the Upper Cabinet - Remove the drawer, pre-drill a 5mm hole screw
up through the top panel of the drawer unit into the base of the upper Cabinet. Attach the two units
together using the 28mm screws supplied.
Step4 – Attaching the Drawer Unit to the Upper Cabinet and WallBed
Caution: Do Not over tighten the wood screws into the side of the wall
bed End Panel or bottom of the top cabinet as it may end up protruding
through the opposite side of the panel.

Removing Panel Stickers/Labels
To remove once installed, heat up with hair dryer & then to remove any sticky residue
use wax and grease remover or similar.
Avoid using a razor blade as you may damage the cabinetry.
9
Attaching the Door to the Cabinet - Clip the hinge arm into the hinge block previously attached to
the bookcase.
Attaching the Cabinet to your wall bed - Check that the cabinet door panel is flush with the front
edge of the wall bed End Panel. Using existing shelf pin holes (2 up towards the top and 2 at the
bottom) attach the bookshelf to the side of the bed cabinet by using the 28mm wood screws
supplied.
Cover the screw heads using the stick on Fast-caps.
Caution: Do Not over tighten the wood screws into the side of the wall bed End Panel as it may end
up protruding through the opposite side of the panel.
Adjustable Shelf - Insert the shelf pins into the shelf pin holes at the desired height for your shelf.
Place your shelf on them. If you find it’s too high or too low for the books you want to store, it’s an
easy matter to adjust the shelf by moving the supports to the holes at the required height.
Attaching the door handle
Place the handle over the pre-drilled holes in the door panel. Insert the handle screws
through the pre-drilled holes in the door panel and tighten using a Phillips head screw driver.
©2019 WallBeds Australia
Cupboard Door Hinges –
Place the cup part of the hinge into the cupboard door panel, ensuring that the arm of the hinge is facing
out of the door panel. Once in the position close the hinge flap, this will secure them into place. There are
no screws required to attach these hinges.
IMPORTANT SAFETY INFORMATION
All WallBeds Australia Bookcases and Cabinets must be securely attached
to the WallBed before use. Ensure that children DO NOT climb or hang on
any part of the Bookcase or Cabinet.
Failure to do so may result in personal injury.

Image 3
Image 4
Image 5
Image 1
Image 2
©2019 WallBeds Australia
10