Wallbeds Australia AB1a User manual

AB1a- Cabinet Assembly Instructions
Note: If you have two ofthe same cabinet each cabinet will have adifferent cabinet number.
Panel Stickers/Labels –Donotremove any cabinet stickers from the panels until the
units havebeen built, as these will assist with assembly. Most of the stickers are placed
on the “back” orunderside of the cabinet and will notbe seen once assembled.
AB1a Cabinetry Panels
1
End Panel Back Panel Door Panel End Panel
Top & Bottom Panel
Kick Panel
Adjustable Shelf

Cam Pins Insert all Cam Locks into the following panels asdescribed bythe cabinet part located
on the cabinet sticker.
Cam Lock Cam Pin
Door Hinge Clip
Small Handle Handle Fixing Screw
Door Hinge
Shelf Pin
AB1a Hardware Parts
Cam Locks – Insert all Cam Locks into the following panels asdescribed by the cabinet part
located on the cabinet sticker.
Back Bottom Top
Rail
End End
Bottom Top
NOTE: In the Top and
Bottom Panels Insert the
cam pins on the opposite
side to the Cam Lock.
Step 1– Inserting Cabinetry Hardware
2

3
Door Hinge Clips –
Attach the Hinge Plates before assembling the cabinetry.
With the arrow indicator on the hinge block facing to the front edge of the panel. Line up the
Hinge Plate with the pre-drilled holes in the End Panel. Fix these by tapping them in gently with
ahammer,then tightening the screws.
Step 2 – Cabinet Assembly
Start the cabinetry assembly by using either one of the End Panels
Back Panel -Ensuring the cam locks are facing away from the inside. Place the cabinet back
panel onto the side panel. Match up the cam locks with the cam pins. Tighten the cam locks
and cam pins together byusing a Phillips head hand screwdriver.
End Panel - With the cam locks facing away from the inside of the cabinet attach the bottom
panel to the end panel and back panel.
Top Panel - With the cam locks facing the outside of the cabinet attach the bottom panel
to the end panel and back panel. - It is essential that the cam locks are facing the outside of
the cabinet.
Place the remaining end panel on top ofthe previously assembled panels. Ensuring the cam pins
are lined up with the cam locks. Tighten the cam pins to the cam locks.
Note: You may need to lightly tap the cam pins into the cam locks with a rubber mallet. Ensure you
do this where the cam pins are located. Failure to do so may result in damage to the End Panel.
Step 3– Fixing Pull Out Cabinet to the Alpha Wall Bed
Place the cabinet next to the side of the Alpha Wallbed that it will be attached to PRIOR to
attaching the door panel. Once the cabinet is in place next to the wall bed then fit door hinges to
the cabinet door and attach the door to the cabinet.
Step4– Fitting the Door Hinges and Door Panel
Cupboard Door Hinges –
Place the cup part of the hinge into the cupboard door panel ensuring that the arm of
the hinge is facing out of the door panel. Once in the position close the hinge flap, this
will secure them into place. There are no screws required to attach these hinges.

Removing Panel Stickers/Labels
To remove once installed, heat up with hair dryer & then to remove any sticky residue
use wax and grease remover or similar.
Avoid using a razor blade as you may damage the cabinetry.
4
Attaching Door Handle -
Place the handle over the pre-drilled holes in the door panel. Insert the handle screws through
the pre-drilled holes in the door panel and tighten using a Phillips head screw driver.
Attaching the Door to the Cabinet - Clip the hinge arm into the hinge block previously attached
to the bookcase.
Attaching the Cabinet to your wall bed - Check that the cabinet door panel is flush with the front
edge of the wall bed End Panel. Using existing shelf pin holes (2 up towards the top and 2 at the
bottom) attach the bookshelf to the side of the bed cabinet by using the 28mm wood screws
supplied.
Caution: Do Not over tighten the wood screws into the side of the wall bed End Panel as it may
end up protruding through the opposite side of the panel.
Adjustable Shelf - Insert the shelf pins into the shelf pin holes at the desired height for your shelf.
Place your shelf on them. If you find it’s too high or too low for the books you want to store, it’s an
easy matter to adjust the shelf by moving the supports to the holes at the required height.