Wallbeds Australia AB-4 User manual

Important Safety Advice Sheet
PLEASE READ BEFORE YOU BEGIN:
•Please read and understand the instructions prior to assembly.
Incorrect installation of this product could possibly result in
personal injury or physical damage.
•WallBeds Australia recommends two people to safely assemble
and install the wall bed - It is not recommended you try to install
this bed on your own.
•The wall bed MUST be securely fastened to the wall prior to use.
Failure to do so will cause the bed to tip over & may cause
damage to the cabinet or serious personal injury.
•All additional cabinetry must be securely fasten to the Wall Bed
cabinet.
•Whilst these products are DIY it is recommended the wall bed be
installed by a qualified trades person if you are not comfortable
with the installation of this product.
WallBeds Australia is not responsible for any damages
or injuries incurred by incorrect installation of this
product.
1
©2020 WallBeds Australia V4

AB-4Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number.
Prior to assembly, separate and group all matching panels numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the units
have been built, as these will assist with assembly. Most of the stickers are placed
on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Back
Kick / Rail
Bottom Panel
Top Panel
AB-4 Drawer Unit Panels
Drawer Front
Drawer Bottom
Drawer Back
2
©2020 WallBeds Australia V4

AB-4 Drawer Unit Hardware
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
Back Panel Bottom Panel Top Panel
Rail / Kick Drw Back
Step 1– Inserting Drawer Unit Hardware
3
Small Handle Drawer Clip
Handle Fixing Screw
Euro Screw Cam Lock
Cam Pin
Done Head Screw
28mm Wood Screw
Drawer Runners &
Metal Drawer Sides
©2020 WallBeds Australia V4

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
Drw Bot
Bottom Panel
Top Panel
NOTE: In the
Bottom Panel Insert
the cam pins on the
opposite side to the
Cam Lock.
Drawer Runners –
Attach the runners prior to assembling the cabinetry.
Drawer Clips –
NOTE: In the Top
Panel Insert the cam
pins on the same
side as the Cam
Lock
4
Insert these into the drawer front, ensuring the up & down arrows on the drawer clips are
facing the outside edge of the drawer panel. Fix these into the drawer front by tapping
them in gently with a hammer - Refer to image 5 page 9
Line up the holes in the metal runner with the pre-drilled holes in the End Panel.
Attach these runners using the Euro screws. Do this for both End Panels- Refer to
images 1 & 2 page 9
End
Left
End
Right
©2020 WallBeds Australia V4

5
Step 2 Ab-4 Drawer Unit Assembly
Start the cabinet assembly by using either one of the End Panels.
Back Panel - With the cam locks are facing away from the inside. Place the cabinet back
panel onto the side panel. Match up the cam locks with the cam pins. Tighten the cam
locks and cam pins together by using a Phillips head hand screwdriver.
Bottom panel - With the cam locks facing away from the inside of the cabinet attach the
bottom panel to the end panel and back panel. Refer to images 6 & 7 page 10
Top Panel - With the cam locks facing the inside of the cabinet attach the bottom panel to
the end panel and back panel. - Ensure the cam locks are facing the inside of the cabinet.
Kick/Rail - With the cam locks facing to the back of the cabinet attach the kick panel
to the end panel.
Place the remaining end panel on top of the previously assembled panels. Ensuring the cam
pins are lined up with the cam locks. Tighten the cam pins to the cam locks.
Drawer Assembly
Note – There are no guide holes on the underside of the drawer bottom panel for the metal
drawer sides. The dome head screws supplied do not require these holes to be pre-drilled.
With the cam locks facing the back attach the drawer back to the drawer bottom panel.
Tighten cam locks to cam pins. Refer to image 4 page 9
Metal Drawer Sides - Using the dome head screws fix the metal drawer sides to the drawer
bottom and drawer back panels . Refer to images 3 & 4 page 9 . Place assembled drawer
into the drawer unit. -
DO NOT ATTACH DRAWER FRONTS UNLESS THE DRAWERS ARE IN THE CABINET.
To ensure you place the drawer front up the correct way Refer to images 8 and 9 on page 10
Do not fully connect the drawer front onto the metal drawer sides until you are sure the drawer
front is up the correct way.
Attaching the Drawer Front - Starting with the top drawer, gently close the drawer ensuring
the top edge of the drawer front is level with the top panel of the drawer unit.
If the drawer front is higher than the top panel, remove it from the drawer clips and turn the
drawer front up the opposite way.
Double-check the drawer front is now level with the cabinet top panel.
Once the drawer front is the correct way up, push the drawer front into the metal sides of the
drawer until you hear the drawer click into place on both sides. Tighten the screws on the
outside of the drawer clips using a Phillips head hand screwdriver. Refer to images 10 & 11 on
page 11
©2020 WallBeds Australia V4

AB-4Bookcase Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the “back” or underside of the cabinet and will not be seen once assembled.
End Left End Right
Bottom Panel
Top Panel
AB-4 Bookcase Panels
Back Panel
6
©2020 WallBeds Australia V4

Cam Pins Insert all Cam Locks into the following panels as described by the cabinet part located
on the cabinet sticker.
Cam Lock Cam Pin 28mm Wood Screw Shelf Pin
AB-4 Bookcase Hardware Parts
Back Bottom Top
Rail
Side / End Side / End
Bottom Top
NOTE: In the Top and
Bottom Panels Insert the
cam pins on the opposite
side to the Cam Lock.
Step 1– Inserting Hardware
Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part
located on the cabinet sticker.
7
©2020 WallBeds Australia V4

•Place the Drawer Cabinet unit next to the side of the Alpha Wallbed that it will be attached to.
Ensure the front edge of the drawers are flush with the front edge of the wall bed cabinet.
•Place the bookshelf unit on top of the drawer cabinet unit and line up the front of the bookcase
bottom panel with the front edge of the drawer.
•Check that the bookshelf end panel is also flush with the front edge of the wall bed cabinet end
panel.
You will need to pre-drill the 5mm screw holes.
When attaching the Pull Out Drawer / Table unit to the bookshelf.
•Remove the pull out drawer / & pre-drill a 5mm hole up through the top panel of the pullout
drawer unit into the bottom panel of the bookshelf. Do one towards the front and then one
towards the back of the unit. IMPORTANT - Use caution not to go all the way through to the
bottom panel of the bookcase. Attach together using the 28mm screws supplied.
•Using an existing shelf pin hole, fix the bookshelf to the side of the bed cabinet by using the
28mm wood screws supplied.
8
Step 2 - Bookcase Assembly
Start the Bookcase assembly by using either one of the Bookcase End Panels and fixing it to the
Back Panel. Ensure the cam locks on the Back Panel are not facing what will be the inside of the
Bookcase when built.
Back Panel - Place the Bookcase Back Panel onto the End Panel. Match up the cam locks with the
cam pins. Tighten the cam locks and cam pins together by using a Phillips head hand
screwdriver.
Top & Bottom Panels - With the cam locks facing away from the inside of the Bookcase attach
the Bottom Panel to the End Panel and Back Panel. Repeat this process with the Top Panel.
Place the remaining End Panel on top of the previously assembled panels. Ensuring the cam pins
are lined up with the cam locks. Tighten the cam pins to the cam locks.
Tip: You may need to lightly tap the cam pins into the cam locks with a rubber mallet. Ensure you
do this where the cam pins are. Failure to do so may result in damage to the End Panel.
Step 3– Fixing both Unitstogether and to the Alpha Wall Bed
Removing Panel Stickers/Labels
To remove once installed, heat up with hair dryer & then to remove any sticky residue
use wax and grease remover or similar.
Avoid using a razor blade as you may damage the cabinetry.
IMPORTANT SAFETY INFORMATION
All WallBeds Australia Bookcases and Cabinets must be securely attached
to the WallBed before use. Ensure that children DO NOT climb or hang on
any part of the Bookcase or Cabinet.
Failure to do so may result in personal injury.
©2020 WallBeds Australia V4

Image 3
Image 4
Image 5
Image 1
Image 2
9
©2020 WallBeds Australia V4

10
Image 8
Image 7
Image 9
Image 6
©2020 WallBeds Australia V4

11
Image 11
Image 12
Image 10
How to remove a drawer front if it has been attached incorrectly
•Insert a small tip screw driver into the hole in the drawer clip as
circled above.
•Apply a small amount of pressure to release the plastic clip
inside.
•Lightly pull on the drawer front whilst pressing on the plastic
clip.
©2020 WallBeds Australia V4

12
NOTE: The images displayed above are a representation of how to place Top unit onto
Lower unit.
These images may not represent each individual product.
IMPORTANT SAFETY INFORMATION
All WallBeds Australia Bookcases and Cabinets must be securely attached
to the WallBed before use. Ensure that children DO NOT climb or hang on
any part of the Bookcase or Cabinet.
Failure to do so may result in personal injury.
©2020 WallBeds Australia V4