Wallbeds Australia Studio Alpha WallBed User manual

Assembly Instructions
Alpha WallBed
Studio Desk
Let’s build a Wallbed together!
** LIFETIME WARRANTY **
Designed to Exceed International ISO 9002
Standards for Residential Specifications
-Patent Pending -
Issue:041414
©2023 WallBeds Australia V1.9
1

Exploded Assembly
(3pc) 2”x3” Fold Hinge
to Desk Back &
WallBed Door
(3pc) Hinge Clips
to WallBed Door
(30pcs) 19mm Self tapping Screw
Pivot Brackets attach to wall bed End/Side Panels. The Desk/Table panels to the
Upper Brackets
(27pcs) Flat Head Self tapping Screw#5x16mm
(10pc) #8x40mm Wood
Screws
ADDITIONAL DESK LEG PACKERS
ATTACH THE DESK PACKER
BETWEEN THE PIVIOT
BRACKET & THE INSIDE OF
THE WALLBED END PANEL
See Images 1 & 4 on page 5
©2023 WallBeds Australia V1.9
2

(4pcs) Black Steel Washer Ø7.0xØ16.0mm
(2pc) M6x40mm Bolt
(2pcs) M6 Nylock Nut
(4pc) Black Nylon Washer Ø13xØ30mm
Washers stop friction between
Legs, Upper and Lower Brackets
Legs to Upper Brackets
Legs to Pivot Brackets
Upper Bracket
(Left and Right)
Leg Packer
(Left and Right)
Pivot Bracket
(Left and Right)
(2pc) Black Steel Washer Ø8.5xØ20mm
(2pc) M8x16mm Bolt
R/H Side When
You Are Facing
The Wallbed.
L/H Side When You Are
Facing The Wallbed.
Studio Desk Hardware
©2023 WallBeds Australia V1.9
3

Important: If the wall bed is slightly too heavy too open and close without the Studio Desk
mounted you should add one Spring to the right and to the left to assist in balance. An odd number
of Springs right and left may be used to get balance.
Steps to Complete the Project
STEP 1: Assemble Desk Top and Back to Upper Desk Brackets.
•Assemble the Desk Top and Desk Back to the Upper Brackets as shown in Drawing #1.
•Using the 19mm wood screws attach the Desk Top panel to the Left and Right Upper Brackets.
•Using the 19mm wood screws attach the Desk Back panel to the Upper Bracket.
•Align the Back Panel with the back edge of the Desk Top panel.
•Attach the Desk Top and Desk Back panels together from the underside with the #8x40mm
Screws.
•HORIZONTAL BED DESK TOP BRACE - The Desk Top Brace panel is attached in the center of
the underside of the Desk Top panel with #8x40mm Screws. See page 5
Fitting Desk Packers
•Place the Desk Packer in front of the Kick Panel on the inside of the wall bed End Panel. Place the
leg and pivot bracket over the Desk Packer. Images 1 & 2.
•Move the leg in a lowering and rising motion. Ensuring the leg does not strike on the wall bed End
Panel when lowering & raising.
•Mark the locations of the fixing holes for the 19mm Self tapping Screw Pivot Bracket screws onto
the Desk Packer. Repeat for the opposite side. Tip: Use your drill with a 5mm drill bit to lightly mark
the locations on the desk packer. Image 2
•Select two locations on the Desk Packer where the pivot bracket attachment screws are not
located. Pre-drill the 5mm countersunk holes for the 28mm Desk Packer attaching wood screws.
Image 3
•Attach the Desk Packers to the wall bed End Panels. Ensuring the head of the wood screw is flush
or lower than the surface of the Desk Packer. Once fully assembled these leg packers will square
up the studio desk legs with the cabinetry.
Image 2 Image 3 Image 4
©2023 WallBeds Australia V1.9
4

How to attach the Desk Top Support Brace
This Desk Top Brace is fixed using 28mm Wood Screws
Assemble the Studio Desk as per Step 1 page 4 of the Studio Desk instructions.
The Desk Top brace is fitted to the underside of the Desk Top
•Measure 150mm from the front edge of the Desk Top. This measurement will put the
Desk Top brace approximately in the middle of the Desk Top underside.
•Place the Desk Top Brace between the fixing brackets that were used to secure the Desk
Top to the bracket.
•Fix the Desk Top Brace to the underside of the Desk Top using the 28mm wood screws
supplied. See the caution note below
A Desk Top Brace has been supplied which attaches to the underside of the Desk Top.
Due to the large span of the Desk Top for an Alpha King Wallbed this brace will reduce the
potential risk of the Desk Top “sagging” over a period of time. This brace will not interfere with
the normal operation of the Studio Desk.
This brace is a precautionary item provided for this product on the advice of the manufacturer
Attaching the Desk Top Brace Panel
Caution
Do not over tighten the 28mm wood screws into the Desk Brace Panel as it
may result with the wood screw protruding through to the Desk Top.
©2023 WallBeds Australia V1.9
5