WatchGas POLI User manual

Quick Start Guide
D e t e c t i on
POLI Multi Gas Detector

Warnings
Read Before Operating
The full POLI User’s Guide must be carefully read by
all individuals who have or will have the responsibility
of using, maintaining or servicing this product. The
product will perform as designed only if it is used,
maintained and serviced in accordance with the
manufacturer’s instructions.
CAUTION
• Change battery only in area known to be non-hazardous.
• UseonlyWatchGas battery PN:M004-3002-W00(12.01.09.0001).
• ATTENTION
• Changez la batterie uniquement dans une zone connue pour
être non dangereuse.
• Utiliser uniquement la batterie WatchGas PN: M004-3002-W00
(12.01.09.0001).
WARNING
• Never operate the monitor when the cover is removed.
• Remove the monitor cover only in area known to be non-
hazardous.
• Use only WatchGas lithium battery part number M004-
3002-W00 (12.01.09.0001).
• This instrument has not been tested in an explosive gas/air
atmosphere having oxygen concentration greater than 21%.
• Substitution of components will impair suitability for intrinsic
safety and void warranty.
• It is recommended to bump test with a known concentration
gas to conrm the instrument is functioning properly before
use.
• Before use, ensure that the colorless ESD layer on the display
is not damaged or peeling. (The blue protective lm may be
removed.)

• AVERTISSEMENT
• N’utilisez jamais le moniteur lorsque le couvercle est enlevé.
• Retirer le couvercle du moniteur et la batterie uniquement
dans une zone connue comme non dangereuse.
• Utilisez uniquement le numéro de pièce de la batterie au
lithium WatchGas M004-3002-W00 (12.01.09.0001).
• Cet instrument n’a pas été testé dans une atmosphère explosive
gaz / air ayant une concentration en oxygène supérieure à 21%.
• La substitution de composants compromettra l’aptitude à la
sécurité intrinsèque et annulera la garantie.
• Il est recommandé de tester avec un gaz de concentration
connu pour conrmer que l’instrument fonctionne
correctement avant de l’utiliser.
• • Avant l’utilisation, assurez-vous que la couche ESD incolore
• de l’écran n’est pas endommagée ou épluchée. (Le lm
protecteur bleu peut être enlevé.)
User Interface
Two key operation, four sensor sockets, one big LCD,
eight alarm LEDs, one buzzer, two vibration alarms.

Turning the unit On
Press and hold the Down Key for 3 seconds, until the
buzzer beeps and the red LED ashes. After a warm up
and self-test sequence, the unit enters normal reading
mode, showing real time gas concentrations.
Turning the unit O
In normal reading mode, press and hold the Down
Key for a 5-second count down, until“Unit O” is
displayed.
Charging
Always fully charge the battery before use. Plug the
charger into the bottom of the POLI. The battery icon
on the LCD shows the charge status. During active
charging, the icon cycles from empty to full and a yel-
low alarm light remains on, which switches to green
when completely charged.
Charging/Comm Cable
The USB Charging/Communications cable allows
charging the unit on a personal computer. A local-
ly-purchased cable can work as well for charging, but
WatchGas cable must be used for proper data transfer
when communicating with WatchGas Suite.
Normal Mode
After warm-up is complete, the unit enters normal
reading mode and displays the instantaneous gas
concentrations continuously.inlet before the instru-
ment is used and replaced once its surface is dirty.

Other values like STEL, TWA, Peak , Min, Date, LEL gas,
etc. can be checked by pressing the Right Key to cycle
through these screens one by one. The Left “Test” key
check alarm function.
Two text and symbol boxes at the LCD bottom are
mapped to the Left [+/OK] and Right [ / ] keys. The
text or symbol in the boxes will vary with the menu.
Conguration Mode
Hold down the Left and Right Keys
together for 3 sec. The cong mode
is password protected with a default
password of“0000”. Input all four digits
and press Left (OK) to enter cong
mode.