WatchGas SST Dock User manual

SST Dock
Quick start guide
SST Dock | QSG | V 1.0 | EN | 28-04-23

2
CAUTIONS & BEST PRACTICES
• If the SST Dock appears to be damaged or is not func-
tioning in the correct way, then please get in touch with
WatchGas or a local representative.
• SST Dock uses Calibration Gas to carry out testing and
calibrations so always ensure that these tests are done in
a well-ventilated environment.
• Always ensure lters are clean and replaced on a regular
basis.
• Avoid the station encountering liquids. SST Dock can not
be mounted in an outside location that could be exposed
to rain or wet conditions.
• Maximum exhaust tubing length is 10 meters.
• Always use the SST Dock in conjunction with a demand
ow regulator.
• SST Dock has no hazardous location approval and can
only be used in a safe and in a non-potentially hazardous
environment known to be free of toxic and / or amma-
ble gas.
• Servicing can only be carried out by a WatchGas ofce or
trained service technician.
• Ensure calibration is the correct quality and that cylin-
ders are with in date and contain gas. Failure to do so
may result in an incorrect calibration.
• Warranty does not cover electrical shock or mechanical
shock and / or water damage.
WARNING
IMPORTANT SAFETY INFORMATION:
READ FIRST
• To ensure personal safety, read Safety Information and
Warnings before using the SST Dock.
• Use the SST Dock only as specied by the manufactur-
er. Failure to do so may impair protection provided by
the SST Dock. The safety and security of any system or
network incorporating the SST Dock and its accessory
components is the responsibility of the assembler of the
system.
• Follow all required National Electric Codes (NEC) and
safety codes.
• Do not attempt to adjust, disassemble, or service the
equipment.
• Only use in a well-ventilated space, in normal atmo-
sphere, 20.9% Oxygen and non-hazardous environment.
• Only use the supplied charging adapter, 12V 1.5A.
• Do not apply positive pressure to the gas inlets. Only use
the demand ow regulator.

3
PREPARE FOR USE
• Use only Luer PG-63 for all gas in and outlets.
• Tube diameter no less than 3mm internal. Tube should be suitable for the gas used, consult
WatchGas for proper Last-o-More tube or compatible tube.
• Only use Demand Flow Regulators from WatchGas compatible part list.
NOTE: Only connect up to 10 meter of tubing on fresh air inlet and outlet.
• Ventilation – the outlet should be connected to a ventilated area.
• Adjust the fresh air purge time accordingly.
• Ensure tubing and cables are proper installed.
• Use of short gas tubing is preferred.
• Ensure fresh air inlet lter is installed.
• If potentially harmful gas are used for calibrations, users must read the MSDS of the gas
connected. The SST Dock must be attached to a venting system or be used in a well-ventilated
area.

4
INTRODUCTION
The SST Dock is an automated test station that allows Bump and Calibration testing and is com-
patible with the full SST Range in one module. It has the capabilities to be connected via Wi-Fi, BLE
or Cellular and allows for desk, wall and hard case mounted dependent on your application. With
two inlets it allows for calibration of the standard four gases plus another gas type. With Built in
NFC it is easier than ever to assign gas cylinders to the correct gas in ports.
1
SST DOCK OVERVIEW
1. Touch screen
2. Touch screen ON / OFF
3. Status LED
4. Instruction label
5. Bottle NFC reader
6. Lid lock
7. Power supply
8. Mounting bracker table / wall mount
9. Exhaust port
10. Port 2
11. Port 2 pressure sensor inlet
12. Port 1
13. Port 1 pressure sensor inlet
14. Fresh air inlet lter
15. Fresh air inlet pressure sensor
16. ON / OFF key
2
3
4
56
7
8
9
10
12
11
13
16
14
15
Figure 1.

5
MOUNTING THE SST DOCK
The SST Dock can be mounted with the invertable mounting bracket in 2 different angels. Use the
extended screws and plastic spacer included in the box.
Wall mounting
The provided mounting brackets can be used to mount the SST Dock to a wall or table. Mounting
screws and plug are not provided. WatchGas recommends to check the strength of the mounting
area and to select the proper mounting hardware before mounting the SST Dock. Mounting the SST
Dock must be performed by a qualied installation contractor.
SWITCH ON THE SST DOCK
If the SST Dock is fully discharged, please allow 5 min of charging prior to switching on the unit.
LED will show red switching to white when prior to start-up.
Connect the SST Dock to Mains by means of the wall adaptor included. The Status light turns on.
Then use the ON / OFF key (g 1. part 16 and part 2) to power on the touch screen.
SST Dock on a wall SST Dock on a table Installing the brackets

6
ENTER SET UP
1. Using Password “admin” to enter the
set up menu
IMPORTANT: If optional pressure sensors are
utilized these shall be activated or the SST Dock
will ignore the signal
Enter the password
2. Add calibration gas bottle in the Gas bottle
list either manual or utilize Watch Tab enabled
bottles. Its important to ll in all data as the
Dock produces a full calibration certicate.
To add a new Calibration bottle click “Add bottle”

7
1. Link the bottle to the input port selected
(the input will light up when the port is
open during operation.
NOTE: The SST Dock will not perform any bump
or calibration if a gas is not matching the detec-
tor target gas.
2. Status LED Green normal operation and
on charge / yellow running on battery / red
fault
3. Server setup – linking to the WatchGas
compliance software the server ID must be
set up. This link will be provided upon pur-
chase of the software
USE
If the touch screen is in sleep mode – double
tap the screen to wake up the unit. The screen
will instruct the next step.
WatchGas App home screen Bump & Calibration

8
INSERTING THE DETECTOR
Step 1
Activate gas detector if required, if it is a 2-
or 3-year SST1 then the device will already be
activated. Turn on NFC.
Step 2
Lift the lid on the SST Dock by using the two
nger guides and the red latch.
Step 3
Insert device by locating the alligator clip into
the guide in the SST Dock.
Step 4
Close Lid until you hear the click.
Step 5
Select the function on the SST Dock display
that you want to carry out: Bump Test, Calibra-
tion, or Fresh Air calibration. The SST Dock will
then carry out the relevant test.

9
SPECIFICATIONS
Dimensions (LxWxH) 28 x 21 x 10 cm
Weight 1.8 kg
Operating Temperature +5-40 °C
Humidity 10% to 90% RH
Storage Temperature 0-50 °C
Power Supply
12 V 1,5 A
L.P.S.
Real Time Clock Yes, updateable
Data Storage More than 1 year of operation
Connection capability Wi-Fi, Cellular, BLE – Connected into the Cloud and WatchGas App
Gas Inlets Fresh air inlet, 2 Gas inlets and one purge
Testing Function Bump Test, Calibration (optional), Device Conguration and Data
Download. Also tests device Alarms, Visual LED’s and Vibrator
Device Compatibility One module compatible with SST Range
Warranty 2 Year warranty

10
MAINTENANCE
WARNING
NO USER-SERVICEABLE PARTS INSIDE
Best practices for maintenance check that inlet lter is free of dirt and replace if required. SST
Dock can be cleaned with a soft, damp cloth. Do not use solvents, soaps, or polishes and do not
immerse the SST Dock in liquids. Completely turn off unit and disconnect power supply before
cleaning.
PARTS AND ACCESSORIES
Replaceable parts and accessories are sold separately. Please contact WatchGas or an authorized
distributor, or visit the website at www.watchgas.com.
WARNING
ONLY USE ORIGINAL WATCHGAS PARTS AND / OR ACCESSORIES
Part list
• WatchGas Demand Flow Regulator
• WatchGas Demand Flow Regulator including pressure sensor
• PG-63 Luer
• Tubing
• Mounting brackets, spacers and screws

11
TROUBLESHOOTING
Detector fails bump, fresh air or calibration:
1. If fresh air fails, verify the lter is not clogged and the air at the inlet is not contaminated.
2. Check if gas bottles are connected, sufciently pressurized and contain the right gas.
(information on the bottle)
3. Verify the station function with a known functional detector.
Detector fails alarm test:
1. Redo the test
2. Manually inspect the detector for LED, vibration and audio alarms
3. Test a known fully functional detector in the station to verify station function
Station fail:
1. Clear fault and retry
2. Contact service representative
CONTACT INFORMATION
Klaverbaan 121, 2908 KD, Capelle a/d IJssel, the Netherlands
[e-mail] | www.watchgas.com
SST Dock | QSG | V 1.0 | EN | 28-04-23 © 2023 WatchGas B.V.
WatchGas is dedicated to continuously improving its products. Therefore, the specications and features mentioned in this QSG are subject to change without prior notice.