Weslo WLEL2947.0 User manual

CAUTION
Read all precautions and
instructions in this manual
before using this equipment.
Keep this manual for future
reference.
Model No. WLEL2947.0
Serial No.
Serial
Number
Decal
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
DIRECTLY.
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
(closed on holidays)
ON THE WEB:
www.wesloservice.com
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
USER'S MANUAL

2
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
HOW TO USE THE ELLIPTICAL EXERCISER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
PART LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
EXPLODED DRAWING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
WESLO is a registered trademark of ICON IP, Inc.

3
IMPORTANT PRECAUTIONS
WARNING: To reduce the risk of serious injury, read the following important precau-
tions before using the elliptical exerciser.
1. Read all instructions in this manual and all
warnings on the elliptical exerciser before
using the elliptical exerciser.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. The elliptical exerciser is intended for
home use only. Do not use the elliptical
exerciser in a commercial, rental, or institu-
tional setting.
4. Keep the elliptical exerciser indoors, away
from moisture and dust. Place the elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around the elliptical exerciser to mount, dis-
mount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. Keep children under 12 and pets away from
the elliptical exerciser at all times.
7. The elliptical exerciser should not be used
by persons weighing more than 250 pounds.
8. Wear appropriate exercise clothes while
using the elliptical exerciser. Always wear
athletic shoes for foot protection while exer-
cising.
9. When mounting and dismounting the ellipti-
cal exerciser, always hold the upper body
arms and step onto and off the pedal that is
in the lowest position.
10. The pulse sensor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The pulse sensor is
intended only as an exercise aid in determin-
ing heart rate trends in general.
11. Keep your back straight when using the ellip-
tical exerciser; do not arch your back.
12. If you feel pain or dizziness while exercising,
stop immediately and cool down.
13. When you stop exercising, allow the pedals
to slowly come to a stop.
14. The warning decal shown on page 4 has
been applied to the elliptical exerciser. If the
decal is missing or illegible, call the toll-free
telephone number on the front cover of this
manual and order a free replacement decal.
Apply the decal in the location shown.
WARNING: Before beginning this or any exercise program, consult your physician.
This is especially important for persons over the age of 35 or persons with pre-existing health prob-
lems. Read all instructions before using. ICON assumes no responsibility for personal injury or
property damage sustained by or through the use of this product.

4
BEFORE YOU BEGIN
Thank you for selecting the new WESLO®FIT BODY
SYSTEM elliptical exerciser. The WESLO FIT BODY
SYSTEM is an incredibly smooth exerciser that
moves your feet in a natural elliptical path, minimizing
the impact on your knees and ankles. Welcome to a
whole new world of natural, elliptical-motion exercise.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number is WLEL2947.0. The
serial number can be found on a decal attached to the
elliptical exerciser (see the front cover of this manual).
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.wesloservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
FRONT
BACK
RIGHT SIDE
Pedal Arm
Pedal Disc
Side Shield
Leveling Foot
Upright
Water Bottle Holder*
*No water bottle is included
Console
Upper Body Arm
Handgrip Pulse Sensor
Wheel
Pedal

5
To hire an authorized service technician to assemble the elliptical exerciser, call toll-free 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the
included hex keys, assembly requires a phillips screwdriver , an adjustable
wrench , and a rubber mallet .
See the drawings below to identify the small parts needed for assembly. The number in parentheses below
each drawing is the key number of the part, from the PART LIST on page 17. The number following the key
number is the quantity needed for assembly. Note: Some small parts may have been preassembled. If a part
is not in the parts bag, check to see if it has been preassembled.
M8 Split
Washer (79)–4
M8 Washer
(64)–4
M10 Split
Washer (78)–4
M8 x 25mm Patch
Screw (70)–2
M8 x 19mm Patch
Screw (73)–4
M8 Nylon
Locknut (59)–6
M10 Nylon
Locknut (84)–4
M8 x 23mm Button
Screw (65)–4
Large Wave
Washer (20)–4
Wave Washer
(27)–2
M4 x 19mm
Screw (68)–6
M8 Large
Washer (81)–2
Star Washer
(85)–6
M10 x 76mm Button Bolt (74)–2M10 x 60mm Button Screw (67)–2
M10 x 75mm Carriage Bolt (58)–2
M4 x 22mm
Screw (66)–2
M8 x 45mm Button
Bolt (11)–4
M6 x 18mm Patch
Screw (87)–4
ASSEMBLY

6
1.
Attach the Rear Stabilizer (35) to the Frame (1) with
two M10 x 75mm Carriage Bolts (58) and two M10
Nylon Locknuts (84).
Press the Stabilizer Endcaps (36) onto the Rear
Stabilizer (35) as shown.
2. Attach the Front Stabilizer (3) to the Frame (1) with
two M10 x 76mm Button Bolts (74), two M10 Split
Washers (78), two Concave Spacers (13), and two
M10 Nylon Locknuts (84). Do not tighten the Nylon
Locknuts yet.
Thread two M10 x 60mm Button Screws (67) with
two M10 Split Washers (78) and two Concave
Spacers (13) through the Front Stabilizer (3) and into
the Frame (1). Tighten the M10 Nylon Locknuts
(84), and then tighten the Button Screws.
Orient a Wheel (28) so the four posts (see the inset
drawing) face away from the Front Stabilizer (3).
Attach the Wheel to the Front Stabilizer with an M8
Nylon Locknut (59). Next, press a Wheel Cover (29)
onto the posts on the Wheel. Attach the other Wheel
(not shown) in the same way.
84
35
1
84
3
78
78
13
13
67
13 78 67
1
36
36
28
29
74
78
13
59
3. While another person holds the Upright (2) near the
Frame (1), connect the Upper Wire Harness (18) to
the Lower Wire Harness (38).
Carefully slide the Upright (2) onto the Frame (1). Be
careful to avoid pinching the Wire Harnesses (18,
38). Attach the Upright with four M8 x 19mm Patch
Screws (73) and four M8 Split Washers (79). Do not
tighten the Patch Screws yet.
3273
73
1
73
79
38
18
79
79
4
4. Identify the Left Pedal Arm (21), which is marked with
a “Left” sticker. Attach a Pedal (19) to the Left Pedal
Arm with three M4 x 19mm Screws (68) and three
Star Washers (85).
Attach the other Pedal (not shown) to the Right
Pedal Arm (not shown) in the same way.
19
21
68
85
85
58
2
28
Posts
1
To make assembly easier, read the information
on page 5 before you begin assembling the
elliptical exerciser.

7
5. Apply a small amount of the included grease to a
Wave Washer (27) and slide it onto one end of the
Pivot Axle (16). Next, slide an M8 Washer (64) and a
Pivot Cover (14) onto an M8 x 23mm Button Screw
(65), and tighten the Button Screw into the Pivot Axle.
Apply a generous amount of grease to the Pivot Axle
(16). Identify the Left and Right Upper Body Legs (6,
7), which are marked with “Left” and “Right” stickers.
While another person aligns the Left and Right Upper
Body Legs with the Upright (2) as shown, insert the
Pivot Axle into the Upper Body Legs and the Upright.
Be careful not to damage the Upper Wire Harness
(18) with the Pivot Axle.
Apply a small amount of grease to a Wave Washer
(27), and place it on the end of the Pivot Axle (16).
Next, slide an M8 Washer (64) and a Pivot Cover (14)
onto an M8 x 23mm Button Screw (65), and tighten
the Shoulder Screw into the Pivot Axle. Make sure
that the Wave Washer remains on the end of the
Pivot Axle.
5
6. Apply a generous amount of grease to the axle on
the Left Upper Body Leg (6). Then, apply grease to a
Large Wave Washer (20) and slide it onto the axle.
Apply a generous amount of grease to the Left
Crank Arm (42). Orient a Crank Arm Spacer (45) so
the flat side is facing away from the Left Crank Arm,
and slide the Crank Arm Spacer onto the Left Crank
Arm.
Slide the Left Pedal Arm (21) onto the Left Upper
Body Leg (6) and the Left Crank Arm (42).
Repeat this step for the other side of the elliptical
exerciser.
6
14
27
7
2
18
73
6
65
64
14
64
27
16
Grease
Grease
65
7. Attach the Left Pedal Arm (21) to the Left Upper Body
Arm (6) with an M8 x 23mm Button Screw (65), an
M8 Washer (64), and a Pedal Leg Cover (23).
Apply grease to a Large Wave Washer (20) and
slide it onto the Left Crank Arm (42). Then, attach the
Left Pedal Arm (21) to the Left Crank Arm with an
M8 x 25mm Patch Screw (70) and an M8 Large
Washer (81).
See step 3. Tighten the four M8 x 19mm Patch
Screws (73).
7
6
21
20
Grease
Grease
42
45
Grease
42
20
81
70
23
64
21
6
65

8
10
59
5
10. Insert the Left Upper Body Arm (4) into the Left Upper
Body Leg (6) and attach it with two M8 x 45mm Button
Bolts (11) and two M8 Nylon Locknuts (59). Make sure
that the Nylon Locknuts are in the hexagonal holes
in the Left Upper Body Leg.
Repeat this step for the Right Upper Body Arm (5)
and the Right Upper Body Leg (7).
8
7
11
6
Hexagonal
Holes
4
910
2
18
Wire Harness
Avoid pinching
the wire
harnesses
87 17
66
9. While another person holds the Console (10) near the
Upright (2), connect the Upper Wire Harness (18) to
the wire harness on the Console.
Attach the Console (10) to the Upright (2) with four
M6 x 18mm Patch Screws (87). Be careful not to
pinch the wire harnesses.
Attach the Water Bottle Holder (17) to the Upright (2)
with two M4 x 22mm Screws (66).
11. Make sure that all parts of the elliptical exerciser are properly tightened. Place a mat under the elliptical
exerciser to protect the floor or carpet from damage.
8. The Console (10) requires four “AA” batteries (not
included); alkaline batteries are recommended.
Remove the battery cover from the Console and
insert four batteries into the Console. Make sure that
the batteries are oriented as shown by the dia-
gram inside the battery compartment. Then, reat-
tach the battery cover.
10
Batteries
Battery
Cover

9
HOW TO USE THE ELLIPTICAL EXERCISER
HOW TO MOVE AND LEVEL THE ELLIPTICAL
EXERCISER
To move the elliptical exerciser, stand in front of it,
place one foot against one of the wheels, and firmly
hold the upper end of the upright. Pull the upright for-
ward until you can move the elliptical exerciser on the
wheels. Carefully move the elliptical exerciser to the
desired location and then lower it to the floor. To
decrease the risk of injury, do not attempt to move
the elliptical exerciser over an uneven surface.
If the elliptical exerciser rocks slightly on your floor,
turn one or both of the levelling feet under the front
stabilizer until the rocking motion is eliminated.
HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, firmly hold the upper
body arms and carefully step onto the pedal that is in
the lowest position. Then, step onto the other pedal.
Push the pedals until they begin to move with a con-
tinuous motion. Note: The pedal discs can turn in
either direction. It is recommended that you turn
the pedal discs in the direction shown below;
however, for variety, you can turn the pedal discs
in the opposite direction.
To dismount the elliptical exerciser, allow the pedals
to come to a complete stop. The elliptical exerciser
does not have a freewheel; the pedals will contin-
ue to move until the flywheel stops. When the ped-
als are stationary, step off the highest pedal first.
Then, step off the lower pedal.
Pedal
Pedal
Disc
Upper
Body Arm
Wheel
Upright
Leveling Foot

10
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
The console offers a selection of features designed to
make your workouts more effective. When you use the
manual mode of the console, you can change the
resistance of the pedals with the touch of a button. As
you pedal, the console will provide continuous exer-
cise feedback. You can even measure your heart rate
using the built-in handgrip pulse sensor.
The console also offers two aerobic programs that
automatically change the resistance of the pedals and
prompt you to vary your pedaling pace while guiding
you through an effective workout.
The console also features four interactive crosstrainer
programs designed to help you to burn calories and
enhance your cardiovascular system while toning and
strengthening your muscles. The crosstrainer pro-
grams automatically control the resistance of the ped-
als and prompt you to perform a variety of strength
exercises during your workout. Note: The strength
exercises require the use of the included dumbbells.
To use the manual mode of the console, see the
instructions at the right. To use an aerobics program,
see page 12. To use a crosstrainer program, see
page 13.
Before using the console, make sure that batteries are
installed (see assembly step 8 on page 8). If there is a
sheet of clear plastic on the display, remove the plastic.
HOW TO USE THE MANUAL MODE
Turn on the console.
To turn on the console, press the On/Reset button
or begin pedaling. The entire display and the pace
guide will light for a moment; the console will then
be ready for use.
Select the manual mode.
When you turn
on the console,
the manual
mode will be
selected. If you
have selected a
program, rese-
lect the manual
mode by pressing the X Trainer Programs or
Aerobic Programs button repeatedly until the scan
and time indicators appear in the display.
Change the resistance of the pedals as desired.
As you pedal,
change the resis-
tance of the ped-
als by pressing
the Resistance
Increase and
Decrease but-
tons. There are
ten resistance levels. Note: After you press the
buttons, it will take a moment for the pedals to
reach the selected resistance level.
3
2
1
Indicators
Pace
Guide