Weslo WLEL31808.0 User manual

Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
V
USERʼS MANUAL
Model No. WLEL31808.0
Serial No.
Write the serial number in the
space above for reference.
QUESTIONS?
As a manufacturer, we are commit-
ted to providing complete customer
satisfaction. If you have questions,
or if parts are damaged or missing,
PLEASE DO NOT CONTACT THE
STORE; please contact Customer
Care.
IMPORTANT: You must note the
product model number and serial
number (see the drawing above)
before contacting us:
CALL TOLL-FREE:
1-866-699-3756
Mon.–Fri. 6 a.m.–6 p.m. MT
Sat. 8 a.m.–4 p.m. MT
ON THE WEB:
www.wesloservice.com
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. eep this manual
for future reference.
Serial Number
Decal

TABLE OF CONTENTS
WARNINGDECALPLACEMENT ..............................................................2
IMPORTANTPRECAUTIONS ................................................................3
BEFOREYOUBEGIN ......................................................................4
ASSEMBLY ...............................................................................5
HOWTOUSETHEELLIPTICALEXERCISER ..................................................10
MAINTENANCEANDTROUBLESHOOTING ...................................................13
EXERCISEGUIDELINES ...................................................................15
PARTLIST ..............................................................................18
EXPLODEDDRAWING ....................................................................19
ORDERINGREPLACEMENTPARTS ..................................................BackCover
LIMITEDWARRANTY ..............................................................BackCover
2
WESLO is a registered trademark of ICON IP, Inc.
WARNING DECAL PLACEMENT
This drawing shows the location(s) of the
warning decal(s). If a decal is missing
or illegible, call the telephone number
on the front cover of this manual and
request a free replacement decal.
Apply the decal in the location shown.
Note: The decal(s) may not be shown at
actual size.

3
WARNING: To reduce the risk of serious injury, read all important precautions and
instructions in this manual and all warnings on your elliptical exerciser before using your elliptical
exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or
through the use of this product.
IMPORTANT PRECAUTIONS
1. Before beginning any exercise program,
consult your physician. This is especially
important for persons over the age of 35 or
persons with pre-existing health problems.
2. It is the responsibility of the owner to ensure
that all users of the elliptical exerciser are
adequately informed of all precautions.
3. Your elliptical exerciser is intended for home
use only. Do not use your elliptical exerciser
in a commercial, rental, or institutional set-
ting.
4. eep your elliptical exerciser indoors, away
from moisture and dust. Place your elliptical
exerciser on a level surface, with a mat
beneath it to protect the floor or carpet.
Make sure that there is enough clearance
around your elliptical exerciser to mount,
dismount, and use it.
5. Inspect and properly tighten all parts regu-
larly. Replace any worn parts immediately.
6. eep children under age 12 and pets away
from your elliptical exerciser at all times.
7. Your elliptical exerciser should not be used
by persons weighing more than 250 lbs.
(113 kg).
8. Wear appropriate exercise clothes when
exercising; do not wear loose clothes that
could become caught on your elliptical exer-
ciser. Always wear athletic shoes for foot
protection.
9. Hold the handlebars when mounting, dis-
mounting, or using your elliptical exerciser.
10. eep your back straight while using your
elliptical exerciser; do not arch your back.
11. The pulse sensor is not a medical device.
Various factors, including the userʼs move-
ment, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
12. When you stop exercising, allow the pedals
to slowly come to a stop.
13. If you feel pain or dizziness while exercising,
stop immediately and cool down.
14. Use your elliptical exerciser only as
described in this manual.

4
BEFORE YOU BEGIN
Congratulations for selecting the new WESLO®
MOMENTUM CT 3.8 elliptical exerciser. The MOMEN-
TUM CT 3.8 elliptical exerciser is a smooth exerciser
that moves your feet in a natural elliptical path, mini-
mizing the impact on your knees and ankles. And the
unique MOMENTUM CT 3.8 features adjustable resis-
tance and an easy-to-use console to help you get the
most from your exercise.
For your benefit, read this manual carefully before
you use the elliptical exerciser. If you have ques-
tions after reading this manual, please see the front
cover of this manual. To help us assist you, note the
product model number and serial number before con-
tacting us. The model number and the location of the
serial number decal are shown on the front cover of
this manual.
To avoid a registration fee for any service needed
under warranty, you must register the elliptical
exerciser at www.wesloservice.com/registration.
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Handlebar
Pedal Disc
Pedal
Console
Resistance Knob
Shield

5
M10
Washer (35)–2
M10 Split
Washer (59)–2
M10 Locknut
(33)–6
Pedal Arm Bolt Set (40)–2
M6 Locknut
(27)–4
M10 x 25mm
Patch Screw (22)–2
M10 x 75mm Carriage Bolt (34)–4M10 x 68mm Button Bolt (48)–2
M6 x 38mm Button Bolt (50)–4
M6 x 45mm Flat Head
Screw (36)–4
Wave Washer
(64)–2
M4 x 16mm
Screw (42)–4
ASSEMBLY
To hire an authorized service technician to assemble the elliptical exerciser, call 1-800-445-2480.
Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the
packing materials. Do not dispose of the packing materials until assembly is completed.
In addition to the included tools, assembly requires a Phillips screwdriver , an adjustable
wrench , and pliers .
See the drawings below to identify the small parts needed for assembly. The number in parentheses below
each drawing is the key number of the part, from the PART LIST near the end of this manual. The number fol-
lowing the key number is the quantity needed for assembly. Note: Some small parts may have been
preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.

6
1.
Identify the Front Stabilizer (10), which is nar-
rower than the Rear Stabilizer (not shown).
While another person lifts the front of the Frame
(1), attach the Front Stabilizer (10) to the Frame
with two M10 x 75mm Carriage Bolts (34) and
two M10 Locknuts (33).
10
33
34
1
1
2. While another person lifts the back of the Frame
(1), attach the Rear Stabilizer (28) to the Frame
with two M10 x 75mm Carriage Bolts (34) and
two M10 Locknuts (33).
34
28
1
2
33
33
33
3. The Console (23) requires four “AA” batteries
(not included); alkaline batteries are recom-
mended. Remove the screw, remove the battery
cover, and then insert four batteries into the bat-
tery compartment. Make sure that the
batteries are oriented as shown by the dia-
gram inside the battery compartment. Then,
reattach the battery cover.
3
To make assembly easier, read the
information on page 5 before you begin
assembling the elliptical exerciser.
23
Batteries
Screw
Battery
Cover

7
4. While another person holds the Console (23)
near the Upright (2), connect the console wire to
the Upper Wire (44). Then, insert the console
wire and the Upper Wire into the Upright.
Tip: Avoid pinching the wires. Attach the
Console (23) to the Upright (2) with four M4 x
16mm Screws (42).
Turn the Resistance nob (63) counterclock-
wise to the lowest setting before going to
the next step.
423
2
44
63
Console Wire
42
5
1
2
33
Avoid pinching the
wires and cables
during this step
Avoid pinching
the wires dur-
ing this step
44
53
48
55
63
59
5. While another person holds the Upright (2) near
the Frame (1), connect the Upper Wire (44) to
the Reed Switch Wire (53).
Next, connect the Resistance Cable (63) to the
Lower Cable (55) in the following way:
•See drawing A. Pull upward on the metal
bracket on the Lower Cable (55), and insert
the tip of the Resistance Cable (45) into the
wire clip inside of the metal bracket.
•See drawing B. Firmly pull the Resistance
Cable (45) and slide it into the metal bracket
on the Lower Cable (55) as shown.
•See drawing C. Using pliers, squeeze
together the prongs on the upper end of the
metal bracket.
Tip: Avoid pinching the wires and cables.
Push the excess cable and wire downward into
the Frame (1). Next, slide the Upright (2) onto
the Frame.
Attach the Upright (2) with two M10 x 68mm
Button Bolts (48), two M10 Split Washers (59),
and two M10 Locknuts (33). Do not tighten the
Button Bolts yet.
55 55
Metal
Bracket
B
AC
55
45
45
45

8
50
8
27
6. Identify the Left Handlebar (6), which is marked
with a “Left” sticker.
Insert the Left Handlebar (6) into one of the
Upper Body Arms (5); make sure that the
hexagonal holes are in the indicated location.
Attach the Left Handlebar (6) to the Upper Body
Arm (5) with two M6 x 38mm Button Bolts (50)
and two M6 Locknuts (27). Make sure that the
Locknuts are inside the hexagonal holes. Do
not fully tighten the Button Bolts yet.
Apply a small amount of the included grease to
the left axle on the Upright (2).
Make sure that there are two Small Handlebar
Bushings (49) in the Left Handlebar (6). Slide a
Handlebar Spacer (47) and the Left Handlebar
onto the left axle on the Upright (2) as shown.
Make sure that the Handlebar Spacer is
turned so the curved side is facing the
Upright. Tap an Axle Cap (14) onto the axle.
Repeat this step for the Right Handlebar (8)
and the other Upper Body Arm (5).
Grease
6
47
14
49
5
2
5
6
7
36
11
13
7. Identify the Left Pedal Arm (11), which is
marked with a “Left” sticker.
Attach a Pedal (13) to the Left Pedal Arm (11)
with two M6 x 45mm Flat Head Screws (36).
Attach the other Pedal to the Right Pedal
Arm (not shown) in the same way.
Hexagonal
Holes

9
9. Make sure that all parts of the elliptical exerciser are properly tightened. Note: Some hardware may be
left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the
elliptical exerciser.
8. Apply a small amount of grease to the axle on
the left Disc Crossbar (16). Slide the Left Pedal
Arm (11) onto the axle, and then slide a Wave
Washer (64) on the end of the axle.
Next, tighten an M10 x 25mm Patch Screw (22)
and an M10 Washer (35) into the axle.
Hold the lower end of the left Upper Body Arm
(5) inside the bracket on the Left Pedal Arm
(11). Next, apply grease to a Pedal Arm Bolt Set
(40). Attach the Left Pedal Arm to the left Upper
Body Arm with the Bolt Set. Do not overtighten
the Bolt Set; the Upper Body Arm must pivot
freely.
Attach the Right Pedal Arm (not shown) to
the right side of the elliptical exerciser in the
same way.
See step 5. Tighten the M10 x 68mm Button
Bolts (48).
See step 6. Tighten the M6 x 38mm Button
Bolts (50) in the Upper Body Arms (5).
Grease
Grease
22 35
11
5
8
16
40
40 64

HOW TO EXERCISE ON THE ELLIPTICAL
EXERCISER
To mount the elliptical exerciser, hold the handlebars
and step onto the pedal that is in the lowest position.
Then, step onto the other pedal. Push the pedals until
they begin to move with a continuous motion. Note:
The pedal discs can turn in either direction. It is
recommended that you move the pedal discs in
the direction shown by the arrow; however, for
variety, you may turn the pedal discs in the oppo-
site direction.
To dismount the elliptical exerciser, wait until the ped-
als come to a complete stop. IMPORTANT: The
elliptical exerciser does not have a free wheel; the
pedals will continue to move until the flywheel
stops. When the pedals are stationary, step off the
highest pedal first. Then, step off the lowest pedal.
HOW TO ADJUST THE PEDALING RESISTANCE
As you exercise,
you can adjust the
resistance of the
pedals with the
resistance knob on
the upright. To
increase the resis-
tance, turn the
knob clockwise; to
decrease the resis-
tance, turn the
knob counterclock-
wise.
10
HOW TO USE THE ELLIPTICAL EXERCISER
Pedal Disc
Pedal
Handlebars
Resistance
Knob