Whalen Emily Full over Twin Loft Bunk Bed with... User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2015-12-19 Rev. 1 Factory: JIYIFO
Emily Full over Twin Loft Bunk Bed with Bookshelf
Stock # M50814
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will
repair or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is
designed to meet your highest expectations. We guarantee that you will immediately see the value of
our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from
State to State.
Customer Service: 866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenstyle.com
ALWAYS USE GUARDRAILS ON BOTH LONG SIDES OF THE UPPER BUNK. IF
THE BUNK BED WILL BE PLACED NEXT TO THE WALL, THE GUARDRAIL
THAT RUNS THE FULL LENGTH OF THE BED SHOULD BE PLACED AGAINST
THE WALL TO PREVENT ENTRAPMENT BETWEEN THE BED AND WALL.
STRANGULATION HAZARD - Never attach or hang items to any part of the bunk bed
that are not designed for use with the bed; for example, but not limited to, hooks, belts,
and jump ropes.
Prohibit more than one person on upper bunk.
Maximum mattress thickness must not exceed 9 in. (22.86 cm). Surface of mattress must
be at least 5 in. (12.70 cm) below the upper edge of guardrails.
Use only mattress which is 74 in. (1.88 m) to 75 in. (1.90 m) long and 52 ½ in. (1.33 m) to
53 ½ in. (1.36 m) wide on upper bunk.
Use only mattress which is 74 in. (1.88 m) to 75 in. (1.90 m) long and 37 ½ in. (95.25 cm) to
38½ in. (97.79 cm) wide on lower bed.
Replacement parts, including additional guardrails, may be obtained from any our dealer.

3
TO HELP PREVENT SERIOUS OR FATAL INJURIES FROM ENTRAPMENT
OR FALLS
•Follow the information on the warnings appearing on the upper bunk end
structure and on the carton. Do not remove warning label from bed.
•Always use the recommended size mattress or mattress support, or both, to help
prevent the likelihood of entrapment or falls.
•Surface of mattress must be at least 5 in. (12.70 cm) below the upper edge of
guardrails.
•Do not allow children under 6 years of age to use the upper bunk.
•Periodically check and ensure that the guardrail, ladder and other components
are in their proper position, free from damage and that all connectors are tight.
•Do not allow horseplay on or under the bed and prohibit jumping on the bed.
•Always use the ladder for entering and leaving the upper bunk.
•Do not use substitute parts. Contact the manufacturer or dealer for replacement
parts.
•Use of a night light may provide added safety precaution for a child using the
upper bunk.
•Always use guardrails on both long sides of the upper bunk. If the bunk bed will
be placed next to the wall, the guardrail that runs the full length of the bed
should be placed against the wall to prevent entrapment between the bed and
wall.
•The use of water or sleep flotation mattress is prohibited.
•STRANGULATION HAZARD – Never attach or hang items to any part of the
bunk bed that are not designed for use with the bed; for example, but not limited
to, hooks, belts, and jump ropes.
•Prohibit more than one person on upper bunk.
•Keep these instructions for future reference.
This product was manufactured December 2015.

4
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Lower Footboard Front Post B- Lower Footboard Back Post C- Lower Headboard Front Post
(Qty. 1) (Qty. 1) (Qty. 1)
D- Lower Headboard Back Post E- Upper Footboard Front Post F- Upper Footboard Back Post
(Qty. 1) (Qty. 1) (Qty. 1)
G- Upper Headboard Front Post H- Upper Headboard Back Post I-
Lower Side Rail
(Qty. 1) (Qty. 1) (Qty. 2)
J- Lower Back Rail K- Upper Cross Assembly L- Upper Cap Rail
(Qty. 2) (Qty. 2) (Qty. 2)
M- Upper Ladder Side Rail N- Upper Mattress Side Rail O- Short Guardrail
(Qty. 1) (Qty. 1) (Qty. 2)
P- Long Guardrail Q- Front Guardrail Post R- Guardrail Support
(Qty. 2) (Qty. 1) (Qty. 2)

5
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
S- Upper Mattress Support Slats T- Left Ladder Support U- Right Ladder Support
(Qty. 1) (Qty. 1) (Qty. 1)
V- Ladder Step XA- Single Bed Headboard Post XB- Single Bed Headboard Post
(Qty. 5) (Qty. 1) (Qty. 1)
XC- Single Bed Footboard Post XD- Single Bed Footboard Post XE- Single Bed Cap Rail
(Qty. 1) (Qty. 1) (Qty. 2)
XF- Single Bed HB Cross Assembly XG- Single Bed FB Cross Assembly XH- Single Bed Mattress Side Rail
(Qty. 1) (Qty. 1) (Qty. 2)
XI- Single Bed Mattress Support Slats YA- Bookshelf Left Side Panel YB- Bookshelf Right Side Panel
(Qty. 1) (Qty. 1) (Qty. 1)
YC- Bookshelf Bottom Shelf YD- Bookshelf Middle Lower Shelf YE- Bookshelf Middle Shelf
(Qty. 1) (Qty. 1) (Qty. 1)

6
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
YF- Bookshelf Middle Upper Shelf YG- Bookshelf Top Shelf YH- Bookshelf Back Panel
(Qty. 1) (Qty. 1) (Qty. 2)
(1) Ø1/4” x 110 mm Bolt (2) Ø1/4” x 45 mm Bolt
(Qty. 24+1 extra) (Qty. 8+1 extra)
(3) Ø1/4” x 38 mm Bolt (4) Ø1/4” x 32 mm Bolt
(Qty. 2+1 extra) (Qty. 20+1 extra)
(5) Ø6.5 mm x 100 mm Tapping Bolt (6) Ø6.5 mm x 48 mm Tapping Bolt
(Qty. 24+1 extra) (Qty. 34+1 extra)
(7) Ø10 x 50 mm Wood Dowel (8) Ø8 x 30 mm Wood Dowel (9) Ø4 mm x 35 mm S
crew
(Qty. 54+2 extra) (Qty. 20+1 extra) (Qty. 40+2 extra)
(10) Ø4 mm x 30 mm Screw (11) Bed Connector Pin (12) Barrel Nut
(Qty. 6+1 extra) (Qty. 4) (Qty. 24+1 extra)
(13) Ø4 mm x 19 mm Screw L-shaped Allen Wrench T-Handle Allen Wrench
(Qty. 2+1 extra) (Qty. 1) (Qty. 1)
Tools required: Allen wrench (provided) and Phillips screwdriver (not provided).

7
BOOKSHELF ASSEMBLING
1. Unpack the units and confirm that you have all hardware and required parts.
2. Locate the Bookshelf Right Side Panel (YB) on a level and protected surface with the threaded inserts
facing up.
3. Insert the 30 mm Wood Dowels (8) into the inner holes of the Shelves (YC, YD, YE, YF and YG) and
attach them to the Bookshelf Right Side Panel (YB) using two 32 mm Bolts (4) per shelf. Securely
tighten the bolts with the enclosed Allen wrench.
YC
YD
YE YF
YG
YB
4
YB
8
Ø1/4” x 32 mm Bolt
(10 used in this step)
④
Ø8 x 30 mm Wood Dowel
(10 used in this step)
⑧

8
BOOKSHELF ASSEMBLING
4. Slide two Back Panels (YH) into the grooves between the lower three shelves (YC, YD and YE) until
fully inserted into the Bookshelf Right Side Panel (YB).
YH YH
YC
YD
YE YF
YG
YH
YC YD YE
YB

9
BOOKSHELF ASSEMBLING
5. Repeat the same procedure to attach the Bookshelf Left Side Panel (YA) at the opposite end. Make sure
that the Back Panels (YH) fit securely into the groove of Side Panel (YA).
6. Ask for assistance to lift the unit upright.
YC
YD
YE YF
YG
YH
YH
YA
YB
YA
4
8
Ø8 x 30 mm Wood Dowel
(10 used in this step)
⑧
Ø1/4” x 32 mm Bolt
(10 used in this step)
④

10
SINGLE BED ASSEMBLING
NOTE: Please follow the instructions carefully to insure a safe and sturdy bed. Do not fully
tighten the bolts until all rails and guardrails are attached.
7. Locate one Single Bed Cap Rail (XE) on a level and protected surface with the holes facing up. Insert
two 50 mm Wood Dowels (7) into the large holes of the Single Bed Headboard Cross Assembly (XF) and
attach it to the Cap Rail (XE) using four 48 mm Tapping Bolts (6). Securely tighten the bolts with the
enclosed L-shaped Allen wrench.
8. Repeat the previous step to combine the Single Bed Footboard Cross Assembly (XG) with the other
Single Bed Cap Rail (XE).
Ø10 x 50 mm Wood Dowel
(4 used in this step)
⑦
XF
XE
XG
XE
XF
6
XE
7
XG
Ø6.5 mm x 48 mm Tapping Bolt
(8 used in this step)
⑥