Whalen Braxton 7-pc Dining Set User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Whalen Furniture Mfg., Inc. Page 1 Factory No. 16650
Braxton 7-pc Dining Set (Table)
Model # BRA7PD-E
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our toll-free customer service number and have your
instructions and parts list ready to provide the model name, part name or factory number:
1-866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday to Friday
Or visit our website www.whalenfurniture.com
Or e-mail your request to [email protected]
LOT NUMBER:
DATE PURCHASED: / /

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 2 Factory No. 16650
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair
or replace it for up to one (1) year from date of purchase. Every Whalen Furniture product is designed
to meet your highest expectations. We guarantee that you will immediately see the value of our fine
furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from
province to province (state to state).
Customer Service: 1-866-942-5362
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenfurniture.com
1. Maximum load weight 181.4 kg (400 pounds).
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts, screws and knobs are tight at least every 3 months or as needed.
GENERAL INFORMATION, TIPS & TRICKS
MAXIMUM RECOMMENDED WEIGHT LOADS
THIS UNIT IS INTENDED FOR USE ONLY WITH THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM
WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 3 Factory No. 16650
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Table Top (1)
B- Inner Leg (2) C- Outer Leg (2)
D- Stretcher (1) E- Mounting Board (2)
(1) 1/4” x 3/4” Bolt (2) 5/16” x 2” Bolt (3) 5/16” x 3” Bolt
(4+1 extra) (16+1 extra) (4+1 extra)
(4) Large Lock Washer (5) Large Flat Washer (6) Small Lock Washer (7) Small Flat Washer
(20+1 extra) (20+1 extra) (4+1 extra) (4+1 extra)
(8) Metal Bracket (2) M4 Allen wrench (1) M5 Allen wrench (1)
Tools required: Allen wrench (provided).

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 4 Factory No. 16650
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Attach the Stretcher (D) between 2 Inner Legs (B) by inserting the 3” Bolts (3) through the Large Lock
Washers (4) and Large Flat Washers (5) through the countersunk holes on the cutout of the Legs and
screw into the Stretcher, as shown in the illustration below. Tighten the bolts with the provided Allen
wrench.
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts.
Large Lock Washer
(4 used in this step)
④
Large Flat Washer
(4 used in this step)
⑤
D
B
3” Bolt
(4 used in this step)
③

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 5 Factory No. 16650
Assembly Instructions
3. Attach the Outer Legs (C) to the Inner Legs (B) by snugly fitting the cutouts together. Make sure that the
threaded inserts for the Mounting Bards (E) point towards the same direction.
BC

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 6 Factory No. 16650
Assembly Instructions
4. Align and attach one Mounting Board (E) to the top of the Legs (B and C) by using four 2” Bolts (2)
and four Large Washers (4 and 5). Tighten the bolts with the provided 5 mm Allen wrench.
5. Repeat last step with the other Mounting Board (E).
E
E
B/C
E
5
2” Bolt
(8 used in this step)
②
Large Lock Washer
(8 used in this step)
④
Large Flat Washer
(8 used in this step)
⑤

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 7 Factory No. 16650
Assembly Instructions
6. Position the Table Top (A) upside down on a level and protective surface, as shown below.
7. Ask for assistance to flip the assembled base upside down and align the pre-drilled holes on the
Mounting Boards (E) with the threaded inserts on the slides supports of the Table Top (A). Securely
screw eight 2” Bolts (2) with the Large Washers (4 and 5) through the pre-drilled holes on the Mounting
Boards (E) and then into the slides supports, using the provided 5 mm Allen wrench.
2” Bolt
(8 used in this step)
②
Large Lock Washer
(8 used in this step)
④
Large Flat Washer
(8 used in this step)
⑤
E
E
A

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 8 Factory No. 16650
Assembly Instructions
8. To secure the legs in place, align and attach the Metal Brackets (8) to the joint of the Inner Leg (B) and
Outer Leg (C) using the 3/4" Bolts (1) with the Small Lock Washers (6) and the Small Flat Washers (7),
two bolts per Metal Bracket. Tighten the bolts with 4 mm Allen wrench.
3/4” Bolt
(4 used in this step)
①
Small Lock Washer
(4 used in this step)
⑥
Small Flat Washer
(4 used in this step)
⑦
C
C
B
A
Metal Bracket
(2 used in this step)
⑧

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 9 Factory No. 16650
Assembly Instructions
9. Ask for assistance to lift the unit upright and position it at the desired location.
10. Unlock the sash locks underneath the Table Top (A) and release the slide locks on both slide mechanisms to
allow the slide to operate, then pull the Table Top wide open equally from both ends.
11. Lift the Butterfly Leaf from the compartment of the Table Top (A) and flip up the Leaf. Unfold the leaf
aprons and rest the leaf onto the top surface carefully.
12. Push the Table Top (A) from both ends to close and lock the sash locks underneath the Table Top and
flip down the black toggle on each slide mechanism to lock the slides in place.
ON OFF

Model # BRA7PD-E
Please call for replacement parts or assistance: 1-866-942-5362
Whalen Furniture Mfg., Inc. Page 10 Factory No. 16650
To Store the Butterfly Leaf When Not In Use
13. Unlock the sash locks underneath the Table Top (A) and release the slide locks on both slide mechanisms
to allow the slide to operate, then pull the Table Top wide open equally from both ends.
14. Flip down the leaf aprons and fold the butterfly leaf to store within the compartment, as shown.
15. Push the Table Top (A) from both ends to close and lock the sash locks underneath the Table Top and
flip down the black toggle on each slide mechanism to lock the slides in place.
ON OFF