WMF WMF 1000 S User manual

33 2356 5000 09.2006
WMF 1000
Commissioning (first commissioning after delivery from factory)
Heed the WMF 1000 user manual, especially the hazard instructions and the
Safety chapter.
Unpacking and Setting up
Unpack coffee machine and set up on a stable, horizontal support
Check the coffee machine for possible transport damage
(in case of doubt: do not put machine into operation and contact WMF service)
Plug the connector into a grounded outlet
Assemble the optional bean hopper attachment
Insert drip tray and drip tray grid
Test water hardness
Plunge included carbon hardness test strips briefly in water (approx. 1 second)
One minute later, read the degree of hardness on the colour scale of the test strip package
The water hardness is set during commissioning.
Prepare water tank
Remove the water tank from the coffee machine
Remove all accessories from the water tank
Rinse the water tank thoroughly with tap water
Do not put the water tank back into the machine yet. The milk hose must be assembled first.
Insert the WMF tank filter
Remove the screen built into the water tank [1]
Place the cartridge adapter on the water spout supports from above (lock pulled) and lock by pressing
the lock down [2]
Unpack the tank filter cartridge and place on the cartridge adapter [3]
With water hardness 0-4, do not use a tank filter.
Assemble the milk hose
The milk hose is already mounted on the all-in-one spout.
For refrigerated milk, use the transparent milk nozzle (assembled on delivery)
For non-refrigerated milk, use the grey milk nozzle from the accessories
Push the all-in-one spout to the lowest position
Insert the milk hose into the guide
Fill the water tank
Fill the water tank with cold tap water (max. 2.8 litres)
Push the water tank back into the machine
Fill the water tank only with fresh, cold water. Never use hot water, mineral water, milk or other liquids.













•
•




11 22 33
Set all-in-One spout:
Press the adjustment lever to the
right of the spout and then move
the spout.
Packaging material in the carton
contains accessories! Do not
throw away!
Keep the original packaging for a
possible return!
For information about the
accessories and the names of
the machine parts, see the user
manual!
For technical data, see the user
manual!
Do not loosen any screws or
remove housing parts - inside
the machine there is deadly peril
due to mains voltage!

Connect milk hose to milk
Place the refrigerated milk directly to the right of the machine
Place the milk hose with the milk nozzle on it into the milk container. The hose end with the milk nozzle
should reach to the bottom of the container.
Milk is a very delicate food. When handling milk, always heed hygiene. Heed the HACCP cleaning sche-
dule! See user manual Chapter 7.
Fill ground coffee hopper
Open the cover towards the back
Fill coffee beans (max. 320 g),
Can be expanded to 500 g with optional, attachable coffee bean hopper
Close the cover
Heed that no foreign bodies land in the coffee bean hopper. Such foreign bodies can damage the grinders
of the coffee mill. This damage is excluded from the warranty.
Switch on coffee machine / Commissioning program
Press the Off/C button
The commissioning program is started.
The desired language for the display guidance is set here.
The commissioning program uses the display to lead you step by step through the commissioning. Follow
the display texts.
The display goes out after 5 seconds and you are lead through the basic settings.
Time
Date
Water hardness
Tank filter
If water filter is set to “yes,” then the filter is rinsed
now.
When rinsing the filter, you will hear unusual noises.
This is normal. The noises will end during the filter
rinse.
time: hh:mm:ss
OK: P change: -/+
time: hh:mm:ss
OK: P change: -/+
date dd:mm:yyyy
OK: P change: -/+
date dd:mm:yyyy
OK: P change: -/+
water hardn.: 13-16
OK: P change: -/+
water hardn.: 13-16
OK: P change: -/+
water filter: no
OK: P change: -/+
water filter: no
OK: P change: -/+
place 3l container
under h.w. spout
place 3l container
under h.w. spout
The machine now heats up!
Place a container for the rinse water under the all-in-one spout (approx. 200 ml)
After the heating up, there is a coffee system rinse. This warms up all the lines.
Duration approx. 40 seconds.
Now the machine is ready to operate.
We wish you great enjoyment with your WMF1000!







language: english
OK: P change: -/+
language: english
OK: P change: -/+
initial setting up
of your WMF 1000
initial setting up
of your WMF 1000
heating up ...heating up ...
your selection pls
24.10.2006 08:15
your selection pls
24.10.2006 08:15
P
select
confirm
–
care button
Browse backwards
Reduce value
+ Browse forwards
Increase value
The new values are saved
when you exit the program.
The set values can be changed
in the „Basic settings“ program
after commissioning.
See user manual
Chapter 4 Settings