Xblue Networks X2020 Reference guide

X2020
Quick Reference Card
Extension Name: ___________________
Extension Number: ___________________
Extension Pswd: ___________________
Check www.xbluenetworks.com/userguide for any
updates to the documentation
09/2011
Copyright XBLUE Networks, 2011
Answer a Call
1. When an incoming call rings at your phone, pick
up the handset or press the speaker button.
2. When you are done place the handset back in
the cradle or press the speaker button.
Place a Call
1. Dial the telephone number and wait 5 seconds
or press the Center Navigation Key ; or press
an available line button and then dial the number.
2. Begin speaking when the called party answers
or pick up the handset to speak privately.
3. When you are through, place the handset back
in the cradle or press the speaker button.
Transfer a Call
1. While speaking to an outside party
3. Press the programmed intercom button or dial
the extension number of the person that will
receive the call.
4. Hang up to complete the transfer
2. Press the Transfer button.
1. Dial the first telephone number or while on a call
2. Press the down arrow which will
open a second calling path
3. Dial the second party to be included in the
conference call.
4. When the second party answers, press the
conference button. All Parties will be in the
conference.
Creating a Conference Call
place the first caller on hold
While on a call press the Hold button to place
the call on hold.
Placing a Call on Hold
While your telephone is idle, press the redial
button
Using the down Arrow Navigation key, select
one of the 30 stored numbers.
To retrieve the held call, press the hold button
again. To retrieve the held call from another
telephone press the respective line button
Redial
Press the center navigation key to dial the
selected number.
1.
2.
1.
2. Down Arrow
Down Arrow
1. While your telephone is idle press the
up arrow to access the Call Log.
2. Select either Dialed, Missed and Received Calls
3. Locate the number to be dialed
4. Press the OK button to begin dialing.
Using the Navigation Keys
Telephone Call Log
LeftArrow
DownArrow
RightArrow
UpArrow
OK
Up Arrow
1. While your telephone is idle press the down
arrow to access or Edit the 10
speed dial bins.
2. Use the down or up arrow to locate the desired
number.
3. Press the OK button to begin dialing.
Programming and Using Speed Dial Numbers
Down Arrow

Connected Night
Telephone ICONS
Message Light Bar
Cell Phone Like Navigation Keys
Message Button
Conference Button
Personal Phone Book
Headset Button
Transfer Button
Redial Button
Hold Button
Mute Button
Speaker Button
Line Buttons
Volume Bar
Telephone Display ICONS
DND Disconnected
The display will show how many new messages you
have. For example, when you have 1 new message
the following will be displayed.
Press the message key to access VM.
1
Using Your Voice Mailbox
It is a good idea to change the default password,
record your personal greeting, and record your
name when setting up your voice mailbox.
1 - Listen to New Messages
2 - Delete All Messages
3 - Record Personal Greeting
4 - Mailbox Password
5 - Record Your Name
6 - Send Message to Mailbox
* - Administration
Press 1 to listen to your new messages
The message will automatically save or you
may delete the message by pressing 3 and *
while it is playing
Password:__________________ (Default is 0000)
Enter your mailbox password. The number of
new messages will be announced.
Accessing your Voice Mailbox Remotely
Call into the system.
When the system answers dial * and then your
extension number.
Dial your Mailbox password
3.
1.
3.
1.
2.
2.
4.
1. Select the Phonebook tab
2. Enter the Name to be associated with this
number.
3. Enter the Number.
4. Select a special ringing tone, if desired
5. Select the a group for this number
1. Select the SIP tab from the main page
2. Enter the X-50 Gateway address in the “SIP
Proxy Server, Outbound Proxy Server,
Registrar Server, and Registrar Outbound
Server” parameters.
3. Set the Phone Number, Display Name,
Authorized ID and Authorized Password.
4. Only on Remote Workers - Click the check box
to enable “Session Timer”
5. Only on Remote Workers - Change the
“Session Expires” from 3600 to 20.
*Use DDNS or a Fixed IP Address on the X-50 for remote workers
1. Open your web browser and then enter the IP
Address of the phone, which is found in the
telephone Menu - 6. Info.
2. Enter the Admin Password (Default is 1234)
Web Browser Programming Interface
Programming your Phonebook
Off Site Telephone Programming