Yale Assure Lock YRD430 User manual

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 1
Failure to follow these instructions could result in damage to the product, voiding the factory warranty and could lead to failure of the product to provide access.
Yale Assure Lock® 2 Key-Free Deadbolt Installation Guide
(Keypad YRD430 or Touchscreen YRD450)
Notice: Before installing your lock, be sure to follow the steps on the yellow Quick Start Guide.
Tools Needed
Standard Phillips
Head Screwdriver
Tools Needed To Adjust An Existing Door
or Prep a New Door
Drill Utility
Knife
Wood
Mortise Chisel
Tape
Measure
Level
Pencil

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 2
In The Box
AA
AA
AA
AA
Yale Smart Module
(with select models)
Exterior Keypad
Interior Lock
Mounting Plate
Batteries
Screws and
Plastic Clips
(pre-installed)
Battery Cover
Guide
Hardware Components
x4
x2
Note: You must use the provided screws from the
hardware pack when installing this lock.
Adjustable Deadbolt
Latch (AYRDB DRIVE
Adjustable Drive-In Deadbolt
Latch available for purchase)
Reset Pin
Strike
Plate
x2
Screw Set D
Silver for
2 to 2-1/4"
Door Thickness
x2
Screw Set C
Black for
Standard 1-3/4"
Door Thickness
x2
Screw Set B
Blue for
1-3/8"
Door Thickness
x2
Optional
Security
Strike Plate
Screws
x4
Strike Plate
and Deadbolt
Screws
x20mm
DoorSense
DoorSense
Screws
Cover Housing
Mounting Tape
Flush Mount Cap

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 3
1Remove Existing Deadbolt
Keep your old deadbolt until your new lock has been successfully installed.
Door Frame

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 4
Check Door:
Tear off the Door Checker page of this guide and follow
instructions to verify your door measurements and make any
needed adjustments.
Note: There are some cases where existing holes cannot be
adjusted to be compatible.
New Door:
Tear off the Template page of this guide and use either 21/8" or
11/2" template to prepare a new door that has no holes or to
adjust existing holes to be compatible.
Check Door Measurements and Adjust If Needed
2
Check Your Door Guide
1/4
1/8 3/8 5/8
3/4
7/8
0123
1/4
1/8 3/8 5/8
3/4
7/8
1/4
1/8 3/8 5/8
3/4
7/8
1/2 1/2 1/2
I
B
Blue
C
Black
D
Silver
EF
45
1/2 1/2
1/4 3/4 1/4 1/4
1/2
1/8 3/8 5/8 7/8 1/8 3/8 5/8 1/8 3/8
A
A. 2" Minimum clearance between top of
existing lever/knob rose (trim) and center
of deadbolt hole.
2" tolerance for optimal Door Sense
location.
B. 1-3/8" Door Thickness se blue Screw; u
Set B (shortest set).
C. 1-3/8" - 1-3/4" DoorThickness; use black
Screw Set C.
D. 1-3/4" - 2-1/4" Door Thickness; use silver
Screw Set D (longest set).
E;u. 2-3/8" Backset se Out of Box latch
setting.
F. 2-3/4" Backset; adjust latch setting.
Instructions on how to adjust the latch
are included in manual.
G. 1-1/2"Face Bore Diameter. Instructions
on how to remove the black adapter from
the lock are included in manual.
1-1/2"tolerance from inside door frame
edgefor optimal Door Sense location.
H. 2-1/8" FaceBore Diameter.
I. Edge Bore Diameter and Depth.
Cross Bore Diameter.
H
3/4
7/8
67
1/2
1/4 3/4
1/8 3/8 5/8 7/8
3/4
7/85/8
CAUTION:
If printed from electronic file,
Measure ruler to check scale.
set print scale to 1:1
G
To ensure a successful installation, measure each aspect of your door and frame as shown in panels (left side of sheet) using
the ruler above. Make sure all of your dimensions are a . See letter definitions below for guidance.
FO LD OVE R DOOR E DGE
Centerline
Center
of 1" (25mm)
hole through
edge of door
For 1-3/8"
35mm()
Thick Door
2-3/8" 60mm Backset()
2-3/4"70mm Backset()
For 1-3/"4
mm(44.5 )
Thick Door
Center
of 2-1/8" (54mm)
hole through face
of door
Center
of 2-1/8" (54mm)
hole through face
of door
Center
of 1" (25mm)
hole through
edge of door
Door
CAUTION:
If printed from electronic file,
Measureadimension
to check scale.
set print scale to 1:1

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 5
Verify Measurements with the Check Your Door Guide
Equals I
Less than I
(Adjust diameter
to 1")
Greater than I
(Your door is not
a match for a
Yale smart lock)
X
1"
(25mm)
Dia.
1" (25mm) Dia.
1" (25mm) Deep
Frame
Equals I
Less than I
(Adjust diameter
and depth to 1")
Greater than I
(Your door is not
a match for a
Yale smart lock)
X
X
2- /8" ( mm)154
OR
1-1/2" (38mm)
Equals G or H
Less than G
(Adjust diameter
to G or H)
Greater than H
(Your door is not
a match for a
Yale smart lock)
X
X
MeasureStrike Pocket
Diameter and Depth
Measure Cross Bore
Supérieur à A
Moins que A
(votre porte n’est
pas compatible avec
une serrure
intelligente Yale)
X
Mesure du dégagement
B, C ou D
X
Mesurer l’épaisseur de la porte
X
2- /8" ( mm)360
or
2-3/4" (70mm)
Backset
Equals E or F
Less than E or F
(Your door is not
a match for aYale
smart lock)
Greater than E or F
(Your door is not
a match for aYale
smart lock)
X
X
Measure Backset
Measure Face Bore Recommended Location
of DoorSense
X
A: Within
2" of Yale
logo on
battery
cover.
G: Within
1-1/2" from
inside
frame
edge.
"2
51(mm)
"1-1/2
38(mm)
Moins que B
(votre porte n’est
pas compatible
avec une serrure
intelligente Yale)
Supérieur à D
(votre porte n’est
pas compatible
avec une serrure
intelligente Yale)
Cut Here

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 6
Check Your Door Guide
1/4
1/8 3/8 5/8
3/4
7/8
0123
1/4
1/8 3/8 5/8
3/4
7/8
1/4
1/8 3/8 5/8
3/4
7/8
1/21/2 1/2
I
B
Blue
C
Black
D
Silver
EF
45
1/21/2
1/4 3/4 1/41/4
1/2
1/8 3/8 5/8 7/8 1/8 3/8 5/8 1/8 3/8
A
A. 2" Minimum clearance between top of
existing lever/knob rose (trim) and center
of deadbolt hole.
2" tolerance for optimal Door Sense
location.
B. 1-3/8" Door Thickness se blue Screw; u
Set B (shortest set).
C. 1-3/8" - 1-3/4" Door Thickness; use black
Screw Set C.
D. 1-3/4" - 2-1/4" Door Thickness; use silver
Screw Set D (longest set).
E; u. 2-3/8" Backset se Out of Box latch
setting.
F. 2-3/4" Backset; adjust latch setting.
Instructions on how to adjust the latch
are included in manual.
G. 1-1/2" Face Bore Diameter. Instructions
on how to remove the black adapter from
the lock are included in manual.
1-1/2" tolerance from inside door frame
edgefor optimal DoorSense location.
H. 2-1/8" Face Bore Diameter.
I. Edge Bore Diameter and Depth.
Cross Bore Diameter.
H
3/4
7/8
67
1/2
1/4 3/4
1/8 3/8 5/8 7/8
3/4
7/85/8
CAUTION:
If printed from electronic file,
Measure ruler to check scale.
set print scale to 1:1.
G
To ensure a successful installation, measure each aspect of your door and frame, as shown in panels (left side of sheet) using
the ruler abo ve. Make sure all of your dimensions are a . See letter definitions below for guidance.
Cut Here

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 7
Template to Mark a Door for 21/8" Face Bore
FOLD OVER DOOR EDGE
Centerline
Center
of 1" (25mm)
hole through
edge of door
For 1-3/8"
35mm()
Thick Door
2-3/8" 60mm Backset()
2-3/4" 70mm Backset()
For 1-3/ "4
mm(44.5)
Thick Door
Center
of 2-1/8" (54mm)
hole through face
of door
Center
of 2-1/8" (54mm)
hole through face
of door
Center
of 1" (25mm)
hole through
edge of door
Door
CAUTION:
If printed from electronic file,
Measure a dimension
to check scale.
set print scale to 1:1.
Cut Here

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 8
Template to Mark a Door for 11/2" Face Bore
FOLD OVER DOOR EDGE
2-3/4" 70mm Backset()
For 1-3/ "4
mm(44.5)
Thick Door
CAUTION:
If printed from electronic file,
Measurea dimension
to check scale.
set print scale to 1:1.
Centerline
For 1-3/8"
35mm()
Thick Door
2-3/8" 60mm Backset()
Center
of -1/"12
( mm)38
hole through
face of door
Center
of -1/2"1
( mm)38
hole through
face of door
Center
of 1" (25mm)
hole through
edge of door
Center
of 1" (25mm)
hole through
edge of door
Door
Cut Here

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 9
Install Deadbolt Latch and Strike Plate
3
*Correct deadbolt latch length is based on backset. Choose 23/8" or 23/4".
Door Checker measurements E and F can help you verify your backset measurement.
23/8"Backset, Out of Box
23/4" Backset, optional
*Backset
To Adjust:
Twist neck while holding body stable.
If the deadbolt latch is extended,
use your fingers or a small
flathead screwdriver to rotate slot
until deadbolt latch is retracted.
Security screws can be
used here, in place of the
small strike plate screws.
Deadbolt latch must be
in unlocked position. UP
arrow must face upwards.
Frame
Door
Align
strike
with
deadbolt
latch
2-3 /8
2-3 /8 2-3 /4
x2
For Deadbolt
Latch
(Actual Size)
For Strike Plate
(Actual Size)
x2

Part of ASSA ABLOYP/N YRD400-KF-0022 Rev ATrusted every day 10
Verifying Bore Face Measurement for Exterior Keypad
4
Install the lock with the door open.
Do not close until all steps are completed.
Measurement G on the Door Checker will help
verify your bore face measurement.
If hole is less than 21/8", remove adapter by
unscrewing the two screws on either side, using a
Phillips #2 screwdriver.
Inside of Door Outside of Door
2 screws
installed
here, one on
each side
Adapter
Screws
Top of Adapter
Once confirming your bore face measurement is correct, you are ready
to install the Mounting Plate and Keypad.
Feed keypad wire under
deadbolt latch.