Yale Assure Lock YRL216 Technical specifications

P/N - - Rev AYRL LPBINSTL FUL
1
Yale Assure Lock Lever Push Button
®®
Installation and Programming Instructions
(YRL216)
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO
THE PRODUCT AND VOID THE FACTORY WARRANTY
#7 wood & #8-32
machine x 20mm
Combination screws
x4
M4 x 22mm
Pan head machine
screws
x2
#8-32 x 5/16"
Machine screws
x2
Optional
Network Module
Battery Cover
Key
AA Alkaline
Batteries
Latch
Strike Plate
Interior Mounting Plate
Interior Lock
Battery Cover
Template
Keys
Levers
Cylinder
®
Before you begin
for step-by-step installation
instructions & to register
your product
DOWNLOAD
THE BILT APP

P/N - - Rev AYRL LPBINSTL FUL
2
Preparing to Install
Utility Knife
Drill Wood Mortise
Chisel
Pencil Tape
Measure
Level
Tools necessary only for new
doors or adjusting existing prep.
Template
Tools Needed
Standard
Phillips Head
Screwdriver
2-3/8" through bolt posts
2-3/4" through bolt posts
Note: Adjustment based on
backset
O
optional
default
PULL
*Backset
*2-3/8" (60mm) or 2-3/4" (70mm)

P/N - - Rev AYRL LPBINSTL FUL
3
Checking Measurements
See
Door Prep
Template
2-3/8" or 2-3/4"
(60mm or 70mm)
Backset
2-1/8" (54mm)
Diameter
1-3/8" or 2-1/4"
(35mm or 57mm)
Door Thickness

P/N - - Rev AYRL LPBINSTL FUL
4
?Determining Door Handing
Left Hand Right Hand
Face a door swinging open
away from you.
If it swings open to the right,
it is a right hand door. If it
swings open to the left, it is a
left hand door.
Exterior
Inswinging Door
Interior Left Hand
Reverse
Right Hand
Reverse
Face a door swinging open
toward you.
If it swings open to the right, it
is a right hand reverse door. If it
swings opens to the left, it is a
left hand reverse door.
Exterior
Outswinging Door
Interior
Curve of latchbolt must contact strike plate first.
Frame
Door
Latchbolt Curve
Strike
Plate
Exterior
Interior
Outside of Door

P/N - - Rev AYRL LPBINSTL FUL
5
Preparing Door & Frame
Necessary for new doors or adjusting existing prep.
1" (25mm)
Deep
!
Drill holes 1/2 way
through door then
complete from other side
to prevent splitting.
2-1/8"
(54mm)
Dia.
2-3/8" (60mm)
or
2-3/4" (70mm)
Backset
1"
(25mm)
Dia.
See
Door Prep
Template
Inside
of Door
Frame
Frame

P/N - - Rev AYRL LPBINSTL FUL
6
x4
1Installing Latch & Strike Plate
Right Hand Installation Shown
Outside of Door
Frame

P/N - - Rev AYRL LPBINSTL FUL
7
2
Outside of
Right Hand Door
Inside of
Right Hand Door
Installing Push Button
Right Hand Installation Shown
!
!
“TOP” mark must be
on top surface and tailpiece
in vertical position.
Incorrect orientation will
cause lock to fail.

P/N - - Rev AYRL LPBINSTL FUL
8
x2
3Installing Interior Mounting Plate
Right Hand Installation Shown
Inside of
Right Hand Door
Inside of
Right Hand Door

9
4
P/N - - Rev AYRL LPBINSTL FUL
Attaching the Cable Assembly
Right Hand Installation Shown
Inside of
Right Hand Door

P/N - - Rev AYRL LPBINSTL FUL
10
5
X2
Inside of
Right Hand Door
Installing Interior Lock
Right Hand Installation Shown
“Click”
X

P/N - - Rev AYRL LPBINSTL FUL
11
6Installing Exterior Cylinder
Outside of
Right Hand Door
!Cylinder must be installed
with bar away from latch.
Bar
Latch

P/N - - Rev AYRL LPBINSTL FUL
12
7
8
Installing Exterior Lever
Installing Interior Lever
Outside of
Right Hand Door
Inside of
Right Hand Door
!Press pin while installing
lever so lock is not damaged.
!
Press pin while installing
lever so lock is not damaged.

P/N - - Rev AYRL LPBINSTL FUL
13
Testing Thumbturn Operation
Outside of
Right Hand
Door
Outside of
Right Hand
Door
!Test with door open.
!If thumbturn operation test fails, check installation beginning with Step 3.

P/N - - Rev AYRL LPBINSTL FUL
14
Testing Key Operation
Outside of
Right Hand
Door
Outside of
Right Hand
Door
!Test with door open.
!If key operation test fails, check installation beginning with Step 6.

P/N - - Rev AYRL LPBINSTL FUL
15
9Installing Optional Network Module
NOTE: If a network module was included with your lock, it
is in a separate box with additional module installation
instructions.
Inside of
Right Hand Door

P/N - - Rev AYRL LPBINSTL FUL
16
10
Inside of
Right Hand Door
Installing Batteries & Cover
Congratulations, you've installed the
Yale®®
Assure Lock Lever Push Button ( )!YRL216
Programming Instructions will help
you customize your product.

P/N - - Rev AYRL LPBINSTL FUL
17
Testing Push Button Operation
!Test with door open.
!
A Master Code must be created upon installation or after resetting the lock to factory default. ProgrammingPIN
and use of lock is not possible until this step has been successfully completed. See of Programming
Instructions below.
1
If push button operation test fails, check installation beginning with Step 2.
Enter CodePIN
Press

18
P/N - - Rev AYRL LPBINSTL FUL
Resetting Lock to Factory Default
Reset Button
Interior Lock
When resetting the lock, all user codes, including the Master code*,PIN
are deleted. All programming features are reset to original default
settings. See “Factory Settings”.
1. Remove the battery cover and batteries.
2. Remove the interior lock to access the reset button.
3. The reset button (see image above) is marked.
4. Re-insert 3 batteries and hold the reset button for 3 seconds.
5. While still holding the reset button, insert the 4th battery, and hold the
reset button for an additional 3 seconds.
6. Release the reset button.
7. Re-install the interior lock onto the door.
*Upon reset, Master Code creation is the only option available andPIN
must be performed prior to any other programming of the lock.

P/N - - Rev AYRL LPBINSTL FUL
19
Changing Lock: Replacing Cylinder
Factory Settings
*The Master code must be created prior to any other programming of the lock.PIN
Registration required*
Settings Factory Setting
Master CodePIN
Automatic Re-lock Disabled
Lockout Mode Disabled
Wrong Code Entry Limit 5 Times
Shutdown Time 60 Seconds
Audio Mode Enabled
One Touch Locking Enabled
Inside Indicator Light Disabled (Off)
Automatic Re-lock Time 30 Seconds
1.To Remove cylinder:
See installation Step 6 "Installing Exterior Lever" and reverse appropriate
actions to remove the exterior lever handle and cylinder.
2.To install new cylinder:
A. Follow appropriate actions of installation Step 6 "Installing Exterior
Lever" to replace the cylinder and exterior lever handle.
B. Test operation of new cylinder and key by following "Testing Operation".

P/N - - Rev AYRL LPBINSTL FUL
20
Hardware Troubleshooting
Cycle lock in both the locked and unlocked positions. If problems are found:
Bolt will not deadlock and/or lock signals failure via beeps
a. Check for sufficient clearance of the bolt within the strike-side jamb. Correct this by
increasing the depth of the pocket for the bolt.
b. Check for misalignment of bolt and/or strike which may be preventing bolt from
properly entering the strike. With the door open, extend and retract the bolt; if it is
smooth, check the strike alignment.
Bolt does not extend or retract smoothly and/or lock signals failure via beeps
a. Bolt and strike are misaligned, see above.
b. Check the backset of door relative to adjustments already made to bolt.
c. Verify proper door preparation and re-bore holes that are too small or misaligned.
d. Verify push button wire harness is routed properly (see Steps 2 - 4).
Push button numerics are scrolling
Remove interior lock and check to ensure that the wire harness is routed properly
(see Steps 2 - 4).
Thumbturn will not turn
a. Remove interior lock and ensure that thumbturn moves freely.
b. Ensure that spindle is in proper position(Step 2).
Key will not turn
a. Remove interior lock and ensure that key rotates freely.
b. Ensure that key cylinder is properly installed in lock (Step 6).