Yale nexTouch Technical specifications

1
P/N 80-9086-0030-010 (03-18)
Retrofitting or modifying this product may impact fire rating, safety features and warranty.
Consult with code specifications to ensure compliance with all codes and ratings.
nexTouch®
Touchscreen and Push Button Keypad Sectional Mortise Lock
Installation and Programming Instructions
1/2"3/4"
3/32"
AA
AA
AA
AA
Optional
#3 & #2
1/8"

2
P/N 80-9086-0030-010 (03-18)
?Determining Handing
The hand of a door is determined from the secure side of the door.
The term "secure" means the side from which you unlock and enter.
RED Locking Slide
should face the secure
side of door.
Latchbolt -
Beveled edge
must face strike.
(See step 1
to reverse
latchbolt.)
Deadbolt
Key cylinder used for cylinder
option installation.Thumbturn
used when mortise lock is
equipped with deadbolt.
!

3
P/N 80-9086-0030-010 (03-18)
1Handing Latchbolt & Hubs
(If Necessary)
Locking
Slide
1
2
2
2
1
PUSH away from
square hole to create gap.
Check for free movement
of locking slide.
PUSH IN
causing locking slide
to rotate.
3
!
RED MARK on locking slide
must be on secure side of door!
Continue to
rotate locking
slide from other side
until "set" in position.
Insert flat head
screwdriver to
pry latch head up.
Rotate latch head
to correct orientation.

4
P/N 80-9086-0030-010 (03-18)
2Preparing Door
Inside of Door
Outside of Door
!
Drill thru holes 1/2 way
thru door then complete
from other side to
prevent splitting.
!
Mortise Lock Cable Hole:
Drill only 1/2 way into
door (7/8" depth) then
STOP!
!
Mortise Key
Cylinder Hole:
Drill only 1/2 way
into door ONLY if
lock is equipped
with cylinder.
!
Mortise Deadbolt Thumbturn Hole:
Drill only 1/2 way into door ONLY if
lock is equipped with deadbolt.

5
P/N 80-9086-0030-010 (03-18)
3
x2
#12-24x1" Flat Head Combo Screw
Frame
Optional
Strike Box
Preparing Frame & Installing Strike
i
This prep is standard with
or without deadbolt.
Use #3 Philips head
screwdriver

6
P/N 80-9086-0030-010 (03-18)
Installing Lockbody
4
!Do not tighten screws
until Step 10.
!
Make sure mortise pocket
is free from debris.
x2
Inside
of Door
#12-24x1" Flat Head Combo Screw
Mortise Lock
Cable Hole
Use #3
Philips head
screwdriver

7
P/N 80-9086-0030-010 (03-18)
5Installing Key Cylinder (if applicable)
For Cylinder Option ONLY
STOP Test Operation
!
It may be necessary to
loosen the cylinder set screw
before installing the cylinder.
Outside of Door
2
1
Then, use #2
Philips head
screwdriver to
tighten cylinder
set screw.
First, tighten cylinder
until snug against
door with the Yale
logo horizontal.
Outside
of Door
1
Use #2
Philips head
screwdriver
!
HAND TIGHTEN.
Do not use powered
screw driver.

8
P/N 80-9086-0030-010 (03-18)
6
Adjusting for 1-3/4" to 2-1/4" Door (if necessary)
Use screw pack for thicker door at this step.
Use appropriate fastener lengths to ensure proper installation.
!
Installing Rose Trim - all types
Outside
of Door
Inside
of Door
#8-32x1"
Pan Head Screw
with Thread Locker
(For 1-3/4" Door)
x2
Use #2
Philips head
screwdriver
If provided
If provided
!
Tighten screws
securely but avoid
overtightening and
warping door.

9
P/N 80-9086-0030-010 (03-18)
7
Inside
Spindle
Loosen Inside Spindle
1/2 to 1 turn until
Correct Orientation. Outside
Lever Assembly
Installing Levers
Outside
of Door
1
2
3
Preparing Levers
Inside
Lever Assembly Correct
Orientation
8
Pushing levers together,
use hex wrench
to tighten set screw securely
against spindle.

10
P/N 80-9086-0030-010 (03-18)
9Installing Thumbturn (if applicable)
For Deadbolt Option ONLY
#6x3/8" eadOval H Screw
x2 Inside
of Door
Use #2
Philips head
screwdriver
STOP Test Operation