Zip Elite HydroTap G4 range User manual

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 1 of 20
ZIP HydroTap®G4
User Manual
Affix model number label
here
801981UK

Page 2 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
3. Table of contents
• Elite HydroTap
®
G4.................................... Page 2
• Classic HydroTap
®
G4............................... Page 3
• Arc and Cube HydroTap
®
G4.................... Page 4
• Celsius HydroTap
®
G4 .............................. Page 5
• LCD screen & menu................................. Page 7
• Filter maintenance ................................... Page 17
• Changing the CO2cylinder ..................... Page 19
• Home menu icons.................................... Page 20
• Cleaning.................................................... Page 20
• Contact details ......................................... Page 20
• Date of installation.........
Elite HydroTap®G4
Tap identification, lights and buttons
Chilled
button
Temp
light Filter light Sparkling
button
Elite functionality
The Elite tap uses touch
sensitive controls to dispense
chilled and sparkling water.
When operating the tap
ensure the touch surface
is dry as moisture may
interfere with the sensor touch
control.
Tap lights
Blue CHILLED water light
Continually illuminated
This indicates that the chilled and sparkling water is within the set temperature
range.
Flashing slowly
This indicates that the chilled and sparkling water is outside the set dispense
temperature range.
Wait for the light to stop flashing before dispensing water. The light will
typically flash after switching on, or coming out of sleep mode.
Flashing quickly - warning light
When the indicator light flashes fast and continuous, a system fault has
occurred. Check for details on the faults screen (see page 9). If unable to
rectify, call a qualified service agent.

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 3 of 20
Elite HydroTap®G4
White FILTER light
Filter light off
This indicates the filter is operating within its normal specified lifespan.
Filter light flashing slowly
The light will flash slowly when the filter is due for replacement and the LCD
will show ‘Filter Change. See ‘To change the filter’ page 17.
To dispense water
To dispense chilled water
Touch the blue CHILLED button to dispense chilled water.
To dispense sparkling water
Touch the white SPARKLING button to dispense sparkling water.
Classic HydroTap®G4
Tap identification, lights and levers
Blue CHILLED Blue SPARKLING
Filter light
Classic functionality
The Classic tap uses lever switch
controls to operate the tap.
Lever controls can be pushed back
to dispense water manually, or pulled
forward to dispense water for a fixed
time period, (see page 17). Once
pulled forward, levers need to be
manually returned to the OFF position.
Tap lights
Blue CHILLED water light
Continually illuminated
This indicates that the chilled and sparkling water is within the set temperature
range.
Flashing slowly
This indicates that the chilled and sparkling water is not within the set
temperature range. When the chilled water is at the set temperature, the light
will stop flashing. This could take several minutes.
During heavy usage, the temperature can rise out of this range.
Flashing quickly - warning light
When the indicator light flashes fast and continuous, a system fault has
occurred. Check for details on the faults screen (see page 9). If unable to
rectify, call a qualified service agent.

Page 4 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
Classic HydroTap®G4
White FILTER light
Filter light off
This indicates the filter is operating within its normal specified lifespan.
Filter light flashing slowly
The light will flash slowly when the filter is due for replacement and the LCD
will show ‘Filter Change. See ‘To change the filter’ page 17.
To dispense water
To dispense chilled water
Push the blue CHILLED lever to dispense chilled water.
To dispense sparkling water
Push the blue SPARKLING lever to dispense sparkling water.
Arc and Cube HydroTap®G4
Indicator light
Select button
Safety button
Rotary
control
Arc and Cube functionality
On powerup, wait 30secs. for the
unit to calibrate.
The Arc / Cube control may be
rotated in a forward or reverse
direction to dispense chilled or
sparkling water.
The rotary control is spring loaded in the
forward direction and when released, will
return to the OFF position.
When rotated in the reverse direction the
tap operates in a POT FILL mode. Water
will flow from between 5 and 15 seconds
(This is user adjustable, see page 17). To
reset, return the control to the OFF position
and repeat the step. The control has to be
manually returned to the OFF position.
Tap lights
Blue CHILLED water light
Continually illuminated
This indicates that the chilled water is within the set temperature range.
Flashing slowly
This indicates that the chilled water is not within the set temperature range.
When the chilled water is at the set temperature, the light will stop flashing.
This could take several minutes. During heavy usage, the temperature can
rise out of this range.

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 5 of 20
Arc and Cube HydroTap®G4
Flashing quickly - warning light
When the indicator light flashes fast and continuous, a system fault has
occurred. Check for details on the faults screen (see page 9). If unable to
rectify, call a qualified service agent.
Filter lights
All three tap lights will flash every 10 seconds, indicating a filter change
is required.
Reset the filter light see page 11.
To dispense chilled water
Rotating the control when the indicator light is illuminated blue allows the
dispensing of chilled water.
(If illuminated white, touch the SELECT button until the indicator light
illuminates blue).
To dispense sparkling water
Rotating the control when the indicator light is illuminated white allows the
dispensing of sparkling water.
(If illuminated blue, touch the SELECT button until the indicator light
illuminates white).
Note The SAFETY button has no function other than visual illumination on
the chilled and sparkling configuration.
Celsius HydroTap®G4
Celsius functionality
The Celsius range use a rotary control to
dispense water .
Turning the rotary control in either direction
allows the dispensing of chilled or sparkling
water. For your convenience, the rotary
control is spring loaded, so when released,
will return automatically close the tap.
Tap lights
Warning light
Blue or white CHILLED water
light -
continually illuminated
This indicates that the chilled water is ready.
Warning light
Rotary
control Indicator
light

Page 6 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
Mixer tap functionality and operation
The mixer tap lever is operated
as a conventional ‘flick mixer’.
The hot direction is marked with
a red dot and the cold direction
with a blue dot, for dispensing
cold to warm water.
Moving the lever away from
the tap will increase the flow
rate and towards the tap will
decrease the flow rate.
When the lever is moved in the
direction of the blue dot, the
temperature is decreased and
when moved in the direction of
the red dot, the temperature is
increased. The final temperature
will be dependant on the
temperature of the incoming cold water. The spout may be swivelled, left or
right, for convenience.
Celsius HydroTap®G4
Blue or white CHILLED water light -
flashing slowly
The warning light will flash slowly (1 second on and 3 seconds off) whenever
the water is not at the temperature set point.
The tap may still be operated, but the water may not be at the desired
temperature. The slow flashing light will extinguish once the water reaches the
set temperature. The set point temperature is user adjustable
Filter warning light
The white warning light will flash quickly every 10 seconds when the filter is
due for replacement and the LCD will show ‘Filter Change. (See, To change
the filter’ page 17).
Fault warning light
If there is a fault with the system, both the indicator and the warning light will
flash for half a second on and half second off until the fault is rectified.
(See, System information, page 9) or call Zip on 0345 6 005 005.
To dispense water
To dispense chilled water
Turn the rotary control anticlockwise to dispense chilled water.
To dispense sparkling water
Turn the rotary control clockwise to dispense sparkling water.

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 7 of 20
Zip HydroTap®G4 features a ‘TOUCH’ screen for easy setup and operation
adjustment. (See page 20 for home menu icons).
3LCD Screen
Other possible messages in status window
Status** Information Notes
System Fault Product has one or more system
faults
Refer to section B
- System info.
Change filter Internal filter needs to be replaced Refer to section
C Installation
Set chilled
water
temperature
Filter
usage
Date and
time
**Status
window
Note When selecting new options, the screen will revert to the main menu, if
the screen remains inactive for a period in excess of 10 seconds.
3 - 5OC

Page 8 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
3LCD Screen menu
Main
menu
Sub menu Sub menu
options
Section
Language English / Deutsch
A
Information
• Product info.
• Filters log
• System faults
• Energy
• Module
Revision
Serial number
Product number
Calibration
• Filters
• Faults found
• Reset
B
Installation
• Filter flush
• Filter reset
• CO2 Purge
• Lux sensor
calibration
• Start/Stop
• Internal/External
• Calibration options
• Enable/Disable
C
Service Password
protected
D
Security
• Enable
password
• Set password
• Change password
E
Communication
• Remote monitor
• Remote control
• Wi Fi Options
F
Settings
• Date/Time
• Temperature
• Filter
• Energy modes
• Safety
• Dispense times
• 2hr/24hr Mode
• Hot/Cold set point
• Filter life (Litres)
Filter life (Months)
• Sleep mode options
On/Off modes
• Safety lock
• Cold dispensing
G

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 9 of 20
A. Set language
LCD Screen operation - Section A
LCD Screen operation - Section B
• Press the [MENU] button for
main menu.
• Press the [Language] button.
• Select the language.
• Press [<=] button for the
previous menu.
B. System information
In this section, you can find your product serial number, check system fault
messages or view the filter logs and energy usage of your product.
• Press [Product Info] to view the
current product serial no.
• Press [<=] button for the
previous menu or press [HOME]
button to return to the home
screen.
• Press [System Faults] or [Recent
Fault Log] to check the fault
information.
• Press [<=] button for the
previous menu or press [HOME]
button to return to the home
screen.
• Press [Filter Log] to check the
filter resets.
• Press [<=] button for the
previous menu or press [HOME]
button to return to the home
screen.
• Press the [MENU] button for
main menu.
• Press the [Info] button to
view the current product
serial number and other key
information.
Zip Chilled Sparkling
Zip Chilled Sparkling
Product Info
Zip Chilled Sparkling 15:11 Tue 26, July 2016
System Faults
Filters Log Recent Fault Log
Energy
Total Energy
Zip Chilled Sparkling 15:11 Tue 26, July 2016
Last Period
00010.4
004.4
(kWh)
Reset 00.00.00
HOME
• Press [Energy] to view Total
Energy information.
• Press [Reset] to view the energy
used for a new period.
• Press [<=] for the previous menu
or press [Home] to return to the
home screen.

Page 10 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
C. Install
1.Filterush
Sub menu
1. - Filter flush
2. - Filter reset.
3. - Purge CO2
4. - Lux sensor calibration.
LCD Screen operation - Section C
OPEN
Position
CLOSED
Position
ON
OFF
Once your Zip HydroTap®G4 unit has been installed, go to the install menu to
configure the system settings for your product.
Have a bucket or similar container (not supplied) at the ready to hold a
quantity of water that will be ejected while the filter flush mode is in operation.
Open the filter access door on the front of the HydroTap®G4 and the filter
cartridge will be exposed. Located to the rear right hand side of the cartridge
is a flush line, approx 600mm long and the flush line stop cock. Place the
free end of the flush line into the bucket or container (not supplied).
• Press [MENU] button for main
menu.
• Press the [Install] button. Turn the
stop cock on.
• Press the [Filter Flush] button.
• Press [START] button to start
filter flush. Once the filter flush
is finished, turn the stop cock off
first (ensure the cock is properly
closed) then press [STOP] to end
filter flush mode.
• Press [<=] button for the previous
menu or press [HOME] button to
return to the home screen.
• After initial installation,turning
off the filter flush mode puts the
HydroTap®G4 into calibration
mode. With subsequent filter
changes, the system reverts to
the main menu.
Note Run at least 10 Litres of
water through to flush the filter
of any excess black carbon
particles (this is normal). Once
the filter flush has finished,
press the [STOP] button to
display the main menu
Zip Chilled Sparkling
Zip Chilled Sparkling

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 11 of 20
• Press the [MENU] button for main
menu.
• Press the [Install] button.
• Press the [Filter Reset] button.
• Press the [Reset Filter] button.
• If you need to flush the filter follow
the filter flush guide, see page 9.
• To cancel the filter reset program
press [HOME] or [<=].
• To set the filter life or edit filter
usage, see page 14.
After replacing the filter, the counters should be reset.
2. Filter reset
LCD screen operation - section C
3. CO2purge
4. Lux sensor calibration
• Press the [MENU] button for
main menu.
• Press the [Install] button.
• Press the [Lux Sensor
Calibration] button.
• The lights on the tap head will
flash to confirm calibration.
Note Correct operation of the Lux sensor can be verified by selecting Lux
Sensor - OFF. When the room is subsequently darkened, below the calibrated
light level, the lights will turn off after 30 seconds.
When fitting a new gas cylinder, it is important to purge the gas lines.
• Press the [MENU] button for main
menu.
• Press the [Install] button.
• Press the [Purge CO2] button.
• In the next screen, press the
[START] button to commence the
purging process.
• Wait for the water to stop flowing
through the unit.
• Wait a further 10 seconds after the
water has stopped running. During
this time you will hear the CO2gas
running through the tap.
• Press [STOP] to stop the purge.
Zip Chilled Sparkling
Zip Chilled Sparkling
Zip Chilled Sparkling
Zip Chilled Sparkling

Page 12 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
Caution must be observed when changing any settings within the
service menu as any changes may affect the normal operation of
the unit. This can only be done by a Zip technician. Please contact
your Zip service provider for further assistance.
• Press the [MENU] button for
main menu.
• Press the [Service] button.
• A password is required to enter
service menu.
D. Service
LCD Screen operation - Section D
Note In UK call a licensed
electrician / plumber,or call Zip on
0345 6 005 005, for assistance, service, spare parts or enquiries.
E. Security
The Zip HydroTap®G4 allows the appliance coordinator to set up a password
to protect against users changing the preferred system settings.
To set a password
• Press the [MENU] button for main
menu.
• Press the [Security] button.
• Press [Enable Password].
• Enter a 4 digit password.
• Press [Enter].
To change a password
• Press the [MENU] button for main
menu.
• Press the [Security] button.
• Press [Change Password].
• Enter your old 4 digit password.
• Then enter your new 4 digit
password & press [Enter]. (Once
the password has been set you
will need to enter the password
to access the settings screen. If
you have forgotten the password,
please disconnect the power and
restart your HydroTap®G4).
Zip Chilled Sparkling
Zip Chilled Sparkling
F. Communication
The Zip HydroTap®G4 allows the user to use Wi-Fi to operate the product
remotely. • From the Home screen Press
[Menu].
• Press [Comm’s]
• Enter your 4 digit password to
access the WiFi set up.
• Follow the set up instructions in the
ZipAssist installation manual.

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 13 of 20
LCD Screen operation - Section F
G. Settings
• Press the [MENU] button for main
menu.
• Press the [Settings] button.
• Enter your 4-digit password and
press [Enter].
• Once the password has been set
you will need to enter the
password to access the settings
screen. If you have forgotten the
password see page 12, LCD
screen operation - section E
security.
In the settings mode you will be able
to access the following:
• Press the [MENU] button.
• Press the [Setting] button.
• Enter your 4-digit password and
press [Enter].
• Press the [Date/Time] button.
• Choose ‘12 HOUR’ mode or
‘24 HOUR’ mode by pressing
the square button. The selected
mode will be displayed in dark
grey colour with a tick box on the
right.
• Press [NEXT] button to set time.
Set Date / Time
Zip Chilled Sparkling
Zip Chilled Sparkling
• Select individually the hour,
minutes and day and adjust using
the up and down arrows.
• Select individually the date, month
and year and adjust using the up
and down arrows.
• Press [HOME] to return to the
Home screen.
To disable the WiFi setup, navigate to
the WiFi screen (as above).
• Press [WiFi setup]
• In the next screen Press [Disable]
• Press [<=] button for the previous
menu.
WiFi Setup
Zip Chilled 15:11 Tue 26, July 2016
Cloud server
not registered
Status:
Hotspot disabled
Mode:
Disabled

Page 14 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
3. LCD Screen operation - Section G
Filter
Zip HydroTap®G4 allows the user to adjust filter life and edit filter usage.
To edit the filter life
Press the [MENU] button for main
menu.
• Press the [Settings] button.
• Enter your 4-digit password and
press [Enter].
• Press the [Filter] button.
• Press the [Int Filter Life] button.
• To change filter life, first select
(Litres) or (Months) then press the
up or down arrows to edit filter life.
Note
Filter life increases in 500 litres
increments to a maximum of 10000
litres. Factory set at 6000 litres.
To edit the filter usage
This function is to reset the filter change
display after a filter has reached the
end of its life (see page 17, Filter
maintenance).
• Press the [MENU] button for main
menu.
• Press the [Settings] button.
• Enter your 4-digit password and
press [Enter].
• Press the [Filter] button.
• Press the [Edit Int Filter] button.
• To change filter usage, first select
(Litres) or (Days), then use the up
and down arrows to edit the filter
usage.
Note The filter life may be set as a
function of litres used, or in months
from the filter change. When the first of
these functions is reached (i.e. litres or
months expired), the filter warning light
will be illuminated on the tap.
Either of these functions may be
disabled (see below).

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 15 of 20
3. LCD Screen operation - Section G
Energy modes
This mode allows the HydroTap®G4 to go into energy saving mode. There
are two options available: sleep mode and on/off mode.
It is recommended to recalibrate the lux sensor after selecting any of the
lux sensor options from the sleep mode menu. (See page 11, Lux sensor
calibration).
In sleep mode the unit will go to “sleep” after a 2hr period of inactivity. The
chilled water will be ON or OFF.
• Press the [MENU] button for main
menu.
• Press the [Settings] button.
• Enter your 4-digit password and
press [Enter].
• Press the [Energy Modes] button.
• Press the [Sleep Modes] button
then in the next screen, use the
up and down arrow to select sleep
mode from the 4 options in the
table below.
Sleep Mode Light
level
Time
delay
State Chiller
2 Hours > OFF N/A 2 Hr OFF OFF
Lux Sensor > OFF Dark N/A OFF OFF
Lux Sensor or 2 Hr > OFF Dark 2 Hr OFF OFF
Disable N/A N/A ON ON
To activate sleep mode
Zip Chilled Sparkling
Sleep Modes
Zip Chilled Sparkling 15:11 Tue 26, July 2016
On/Off Modes
Menu
HOME

Page 16 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
LCD Screen operation - Section G
On/Off mode menu
Individual set screen
Group set screen
A
A
Note Any attempt, during off mode, to dispense water, will bring the unit out
of sleep mode. The unit will return to sleep mode after 2 hours of non use.
Please allow sufficient time for the water to reach the set temperature after
disabling the sleep mode.
This screen allows you to select the
individual days for programming.
Only one On/Off period is allowed for
each day.
On/Off mode allows the user to turn the
unit on or off at a specific time.
To activate On/Off mode
• Press the [MENU] button for main
menu.
Press the [Settings] button.
Enter your 4-digit password and
press [Enter].
• Press the [Energy Modes] button.
• Press the [On/Off Modes Menu]
button.
• Select ‘Individual Set’ if you wish
to allocate a specific time for each
day.
• Select ‘Group Set 1’ if you wish to
allocate the same time to all seven
days.
• Select ‘Group Set 2’ if you wish
to allocate the same time to the
five working days (Mon-Fri) and
additional times for weekends
(Sat-Sun).
Note Any attempt, during off mode, to dispense water, will bring the unit out
of energy mode. The system will revert to the energy mode setting after 30
minutes of non use.
• Select ‘Group Set 1’ / ‘Group Set
2’.
• Press button to enable and
set the On/Off time by scrolling
with the up & down arrow keys.
• When in Group Set 2 press
[NEXT] to select Sat-Sun options.
Zip Chilled Sparkling
Zip Chilled Sparkling
Zip Chilled Sparkling

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 17 of 20
Filter maintenance
Dispense times
LCD Screen operation - Section G
The ability to change the maximum
dispensing time for both the hot and
cold water has been introduced. The
default settings for the maximum
dispensing times is 15 seconds. The
operator may change both the hot and
cold dispensing times from 5 to 15
seconds, in increments of 1 second.
To edit the dispensing times.
• Press the [MENU] button for main
menu.
• Press the [Settings] button.
• Enter your 4-digit password and
press [Enter].
• Press the [Dispense Time] button.
• Select the option to change and
scroll using the up and down
arrow keys.
Water filter
The HydroTap®G4 notifies when filter replacement is due. If you notice one
of the following, you will need to change the filter.
• The white change filter light will flash and remain so until reset.
• The filter percentage will show 0% on the home screen.
Note Depending on local water quality conditions and usage, the filter may
require changing anywhere from 1,000 Ltrs to 10,000 Ltrs. You may also
need to replace the filter if you notice unpleasant odours or tastes.
Some water may drip from the filter head (socket) during replacement. Keep
a towel handy to dry up any drips.
To change the filter
• Open the door of the Command-CentreTM.
• Relieve system pressure via the filter flush stop cock, a quick open and
close will do. Use the bucket to catch the discharge.
• Grasp filter cartridge, depress the red lever at the top right of the filter
and rotate the cartridge a quarter turn clockwise, then gently pull down.
3-5oC

Page 18 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
Filter maintenance
Warning: If the HydroTap®G4
is switched off for a long period
of time (e.g. more than a
weekend), run water through the
chilled water outlet for at least 5
minutes before consumption.
• Caution . Asmall amount of water will drip as the cartridge is
removed.
•Do not tilt the cartridge as water may spill from it if tilted.
•Unpack replacement cartridge and remove sanitary cap, write
today’s date where shown on the label.
• Avoid touching the filter o-rings and filter opening as this may cause
bacterial contamination of the cartridge.
• Moisten the o-rings with water, align the front cartridge label to the
left (as shown in the “insert filter” diagram below), and push the new
cartridge up into the filter head.
• Turn the cartridge a quarter turn anticlockwise until the cartridge comes
to complete stop and is locked into position, with the front label facing
forward.
• Initiate the filter flush programme by scrolling through the menu screen
(see page 10).
• When completed, wipe up any spills and dispose of spent filter cartridge
and packaging thoughtfully.
• Close the door to secure the appliance.
• Adjust the filter settings in Section G (see page 14) litres and days.
Air Inlet Filter
The HydroTap®G4 air filter is conveniently located on the outside of the
condenser. The filter screen is a sliding fit in the plastic housing on the left
hands side of the Command-CentreTM. The screen may be removed for
cleaning by sliding it forward. This needs to be inspected at least quarterly,
cleaned and replaced if damaged.
Note For best performance the unit should only be operated with a clean
air filter screen, correctly fitted in place. Maintain at least a 50mm air gap
in front of the screen at all times. Take care not to allow cloths or other soft
materials to accidentally block the air inlet.
Slide to remove

801981UK - Commercial Chilled,sparkling User manual - Sept. 2016- v3.02 Page 19 of 20
Changing the CO2cylinder
CO2Regulator
Note When removing hose, take care not to
lose plastic olive from the fitting.
• Turn the CO2cylinder regulator off, turn clockwise to the end stop.
• Remove the cylinder from the cupboard and disconnect the regulator. If
the braided hose is removed from the regulator, be careful not to lose the
small plastic sealing olive, located inside the end of the hose.
• Screw the regulator and hose assembly clockwise onto the new cylinder.
Be aware that some CO2may be discharged from the cylinder joint. Any
CO2released will be cold.
• Install the cylinder in an upright position (use the hook and loop securing
strap).
• Turn the regulator on (turn regulator knob anti-clockwise to end stop).
• Check all joints for gas leaks using a sponge and soapy water.
• Purge the gas lines, see CO2purge , page 11.
Leak Test
Stage 1
• Turn the gas off.
• Using soapy water applied with a
sponge, or with a brush, cover all of
the gas joints with a liberal amount
of suds.
Stage 2
• Turn the gas on.
• Inspect the joint for leaks.
• If any bubbles appear, the joint will need
to be resealed and tested again.
After replacing a cylinder or after making a gas connection,
perform a leak test to check for gas leaks between regulator and cylinder, and
between regulator and braided hose.
Test for leaks at these two points

Page 20 of 20 801981UK - Commercial Chilled,sparkling user manual - Sept. 2016- v3.02
Contact details
Website: www.zipwater.com/uk
Email: [email protected]
Facsimile: 01362 692 448
Telephone: [phone]
Head Office
Zip Water UK
14 Bertie Ward Way
Dereham
Norfolk NR191TE
As Zip policy is one of continuous product improvement, changes to specifications may
be made without prior notice. Images in this booklet have been modified and may not
be true representations of the finished goods.
For terms of warranty please see the back page of the installation guide, download the
latest copy from www.zipwater.com/uk
The terms “Zip” and “HydroTap” are registered trade marks of Zip
Heaters (Aust) Pty Ltd.
Zip products described in this publication are manufactured under
one or more of the following patents: AU675601, AU637412,
AU635979, GB0422305, GB2065848, US4354049, US5103859,
US5099825 and SA2006/08043. Other patents are in force and
patent applications are pending.
Sleep mode is active.
There are 4 sleep mode options which display this icon on the home screen.
See tap sections for details.
Filter use
This icon displays the filter usage remaining from 100% (new filter) to 0%
(end of life). When it reaches 0% the filter warning light on the tap head will
flash slowly. The filter life can be adjusted by litres and by days used.
50%
Chilled temperature
The temperature of the water in the chilled/sparkling tank will be displayed,
between 3°C and 5°C.
Home menu icon Home menu icons
Cleaning
General cleaning
Do not use strong, corrosive spray or abrasive cleaners / chemicals.
Clean the casing, tapware, external filter, piping and all other fittings with a soft cloth
and mild soap and water.
Do not spray water over the tap as it may damage the low-voltage electronics.
Caution: Should any of the plastic fittings accidentally come into contact with cleaners
with a PH level less than 4, hypochlorite, hydrogen peroxide or any other aggressive
chemical the affected component must be replaced immediately.
Command-CentreTM units must never be located near, or cleaned with water jets.
Avoid using airborne pesticides near the Command-CentreTM.