ZKTeco TL100 User manual

Installation Instruction
Version: 2.1
Date: July, 2016
TL100 Fingerprint Lock With Touch Keypad

Diagram
Before Installation
1
E
L
B
J
H
D
A
C
G
F
I
K
P
M
C
N
Q
O

GH
M
BCIE
20mm
15mm
NF
Packing List
2
85mm
60mm
D
L
105mm
85mm
Wooden Door Security Door
10mm
65mm
A
45mm
55mm
60mm
70mm
85mm
30mm
45mm
55mm
70mm
J
K
Q

3
Door Preparation
1. Check door thickness, prepare the proper screws and spindles.
Door Thickness D Spindle L Spindle J Screw K Screw
45-50 mm 65 mm 30 mm 45 mm
50-60 mm 55 mm
55-65 mm 60 mm
65-75 mm 55 mm 70 mm
75-90 mm 70 mm 85 mm
85 mm
105 mm
60 mm
85 mm
45 mm
Note: Screws and spindles for doors thickness of 45-90mm are all included in the
standard package. Please apply the corresponding package according to the
actual door thickness.

GE
Left Inward Right Inward
Left Outward Right Outward
EG
E
GEG
(Without hooks)
4
2. Check door open direction.
Note : 1. Please install the mortise and strike plate according to the above pictures.
2. Mortise(E) can be applied to different door open directions by adjusting the
direction of latch bolt. Please refer to Tips for further details.
3. Check door type.
Lock without hooks is applied to wooden door,
and lock with hooks is applied to security door.
(With hooks)

2. How to change the handle direction?
Tips
1. How to change the direction of latch bolt?
5
Loose
screw
Front Panel Back Panel
Step1: Push the switch to the end
Step2: Push the latch bolt into the mortise
Step3: Rotate the latch bolt at 180° inside mortise, then loose it.
Œ
Ž
180°

3.How to use mechanical key ? 4. How to use emergency power?
Insert the key into key hole and
rotate 90°, then press down the
handle to open the door.
5. How to change the location of stud bolts?
M3
M5
Note: After holes are drilled on the door, you can adjust stud bolts location
to make the lock suitable.
Step1: Twist down the ten M3 screws and M5 stud bolt to take down
the mounting plate.
6
9V Battery

7
Step2: Twist down the
other stud bolt.
Note: There are four square holes
to be used.
Note: There are two round
holes to be used.
M5
M5

8
1. New lock is configured to grant ANY fingerprint access to unlock.
2. Please register one administrator at least for the new installed lock, If there is no any
administrator, registration for normal users and temporary users are not allowed.
3. The lock is equipped with mechanical keys for manual unlocking. Remove mechanical
keys from the package and keep them in a safe place.
4. To power on the lock, eight alkaline AA batteries (not included) are required.
Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.
5. Do not remove batteries when the lock is in working state.
6. Please replace the battery soon when the lock prompts the voice of low battery.
7. The operation of setting lock has a stand-by time limit of 10 seconds. Without any
activity, lock will shut off automatically.
8. Keep your fingers clean when using this lock.
Cautions

Backset 60mm
E
F
9
center line of the
handle
desired handle
height
door thickness
45~90mm
2. Install the mortise(E)
1. Drill holes on the door
Note 1: Align the template along the vertical
center line of the mortise (E) at the desired
handle height, and tape it to door.
Note 2: Mark the holes first, then start drilling.
Installation
E
F