3One data IES3012G Series User manual

IES3012G Series
Unmanaged Industrial Ethernet
Switch Quick Installation Guide
3onedata Co., Ltd.
Address:
3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website:
www.3onedata.com
Tel:
[phone]
Fax:
[phone]
【Package Checklist】
Please check whether the package and accessories are intact
while using the switch for the first time.
1.
Industrial Ethernet switch
2.
Certification
3.
Quick installation guide
4.
Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
This series are full Gigabit unmanaged DIN-Rail industrial
Ethernet switches. Models as follows:
Model I. IES3012G-4GS (4 Gigabit SFP + 8 Gigabit copper
ports)
Model II. IES3012G-8GT (8 Gigabit copper ports)
【Panel Design】
Top view, Bottom view and Rear view
Front view
1. Grounding screw
2. Relay alarm output terminal block
3. Console port
4. Power input terminal block
5. DIP switch
6. DIN-Rail mounting kit
7. Relay alarm status indicator ALM/ALARM
8. Power supply input status indicator P1/P2
9. Device running status indicator RUN
10. 10/100/1000Base-T(X) Gigabit Ethernet port
11. Ethernet port status indicator
12. 1000Base-SFP Gigabit Ethernet SFP slot
【Mounting Dimension】
Unit: mm
Attention before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
For convenient usage in industrial environments, the product
adopts 35mm DIN-Rail mounting, mounting steps as below:

Check if the DIN-Rail mounting kit is installed firmly.Step 1 Insert the bottom of DIN-Rail mounting kit (one sideStep 2 with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed onStep 3 DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Power off the device.Step 1 After lift the device upward slightly, first shift out theStep 2 top of DIN-Rail mounting kit, then shift out the
bottom of DIN-Rail, disassembling ends.
Attention before powering on:
Power ON operation: first connect power line to the
connection terminal of device power supply, then power
on.
Power OFF operation: first unpin the power plug, then
remove the power line, please note the operation order
above.
【Power Supply Connection】
DC power supply
The series provide 4-pin power supply
input terminal blocks and two
independent DC power supply systems of
PWR1 and PWR2. The power supply
supports nonpolarity and anti-reverse
connection. It can normally operate after reverse connection.
Power supply range: 12～48VDC
【Relay Connection】
Relay terminals are a pair of normally open
contacts in the alarm relay of the device. They
are open circuit in normal non alarm state,
closed when any alarm information occurs. For example: it's
closed and sends out alarm when power off. This series
support 1 channel relay alarm information output, and DC
power alarm output. It can be connected to alarm indicator,
alarm buzzer, or other switching value collecting devices for
timely warning operator when alarm information occurs.
【DIP Switch Setting】
This series provide 4-pin DIP switch for function
settings, where "ON" is enable valid terminal.
Please power off and power on after changing
the status of DIP switch. DIP switch definition as
follows:
1.
Abnormal alarm settings of the
power supply connection
2.
Reserved
3.
Reserved
4.
Reserved
【Checking LED Indicator】
This series provide LED indicators to monitor the operating
status of the device, which can comprehensively simplify the
troubleshooting. The detailed status of each LED is described
in the table below:
LED
Status
Description
P1
ON
P1 is connected and running
normally
OFF
P1 is disconnected and running
abnormally.
P2
ON
P2 is connected and running
normally
OFF
P2 is disconnected and running
abnormally
ALM/ALARM
ON
Power supply link alarm
OFF
Power supply link without alarm
RUN
ON
The device is powering on or
running abnormally.
OFF
The device is powered off or
running abnormally.
Blinking
Blink once per second, and the
device is running well.
Link/ACT
(G1-G8/G12)
ON
Ethernet port connection is
active.
Blinking
Data transmitted
OFF
Ethernet port connection is
inactive.
【Specification】
Panel
Gigabit SFP
1000Base-SFP, SFP slot
Gigabit copper port
10/100/1000Base-T(X)
self-adapting RJ45 port, full/half
duplex self-adapting or specified
operating mode, support
MDI/MDI-X self-adaption
Console port
Reserved
Alarm interface
2-pin 7.62mm pitch terminal
blocks, support 1 channel relay
alarm information output
Indicator
Power supply indicator, running
indicator, interface indicator and
alarm indicator
Exchange attributes
Backplane bandwidth
24G
Packet buffer size
4Mbit
MAC table size
8K
Power supply
Input power supply
12~48VDC
Support dual power supply
redundancy, nonpolarity and
anti-reverse connection
Access terminal
4-pin 7.62mm pitch terminal
block
Consumption
IES3012G-4GS
No-load consumption:
4.85W@24VDC
Full-load consumption:
10.32W@24VDC

IES3012G-8GT
No-load consumption:
4.35W@24VDC
Full-load consumption:
9.56W@24VDC
Working environment
Working temperature
-40~75℃
Storage temperature
-40~75℃
Working humidity
5%~95% (no condensation)
Protection grade
IP40 (metal shell)