3One data IES6320 Series User manual

IES6320 Series
Managed Industrial Ethernet Switch
Quick Installation Guide
3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District,
Shenzhen
Website: www.3onedata.com
Tel: [phone]
Fax: [phone]
【Package Checklist】
Please check the integrity of package and accessories while
first using the switch.
1. Industrial Ethernet switch
2. Certification
3. Warranty card
If any of these items are damaged or lost, please contact our
company or dealers, we will solve it ASAP.
【Product Overview】
This series of product is Gigabit managed DIN-Rail industrial
Ethernet switch. Models as follows:
Model I. IES6320-16GT-2P48 (16 Gigabit copper ports)
Model II. IES6320-16GT4GS-2P48 (16 Gigabit copper ports
+ 4 SFP slots)
【Panel Design】
Top view, bottom view and rear view
Front View
1. Grounding screw
2. Relay alarm output terminal block
3. Console port
4. Terminal block for power input
5. DIP switch
6. DIN-Rail mounting kit
7. Device running indicator RUN
8. Power input status indicator P1/P2
9. Relay alarm indicator ALM
10. 10/100/1000Base-T(X) Gigabit Ethernet Interface
11. Ethernet port link indicator
12. 1000Base-X Gigabit Ethernet SFP slot
【Mounting Dimension】
Unit: mm
Notice Before Mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
The product adopts 35mm standard DIN-Rail mounting which
is suitable for most industrial scenes, mounting steps as
follows:
Check if the DIN-Rail mounting kit is installed firmly.Step 1
Insert the bottom of DIN-Rail mounting kit (one sideStep 2
with spring support) into DIN-Rail, and then insert

the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Check and confirm the product is firmly installed onStep 3
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Power off the device.Step 1
After lifting the device upward slightly, first shift outStep 2
the top of DIN-Rail mounting kit, and then shift out
the bottom of DIN-Rail, disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,
then remove the wiring section of terminal block. Please
pay attention to the above operation sequence.
【Power Supply Connection】
The series of device provides 4-pin power
supply input terminal blocks and supports
two independent DC power supply
systems, PWR1 and PWR2, which
supports non-polarity and anti-reverse
connection function, that the device can work normally after
reverse connection.
Voltage range: 12~48VDC.
【Relay Connection】
Relay terminals are a set of normally open
contacts of the device alarm relay. They are
open circuit in the state of normal non alarm,
closed when any alarm information occurs. For
example, they are closed when powered off, and send out
alarm. The product supports 1 relay alarm information output
that can output DC power supply alarm information or network
abnormality alarm. It can be connected to alarm light or alarm
buzzer or other switching value collecting devices, which can
timely inform operators when the alarm occurs.
【DIP Switch Settings】
The series of devices provide 4-bits DIP switch for
function setting, where "ON" is enable valid terminal.
The definitions of DIP switch are as follows:
PIN
Definition
Operation
1 Reboot
Set the switch to ON, then set it
to OFF after 1-2 seconds, the
system will reboot automatically.
2
Restore Factory
Settings
Set the switch to ON, then set it
to OFF after 5 seconds, the
system will automatically restore
the factory settings.
3-4
Reserved
—
【Console Port Connection】
The series of device provides 1 program debugging port
based on RS232 serial port which can conduct device CLI
command management after connecting to PC. The interface
adopts RJ45 port, the RJ45 pin definition as follows:
Pin No.
2
3
5
Definition
TXD
RXD
GND
【Checking LED Indicator】
The series of devices provide LED indicators to monitor its
operating status, which has simplified the overall
troubleshooting process. The function of each LED is
described in the table below:
LED
Indicate
Description
P1
ON Power P1 is connected and running
normally
OFF
Power P1 is disconnected or
running abnormally
P2
ON Power P2 is connected and running
normally
OFF
Power P2 is disconnected or
running abnormally
ALM
ON
Power supply or port link has alarm
OFF Power supply and port link have no
alarm
RUN
ON The device is powering on or the
device is abnormal.
OFF The device is powered off or the
device is abnormal.
Blinking
Blinking 1 time per second, the
device is running normally.
Link/Act
(1-16/20)
ON
Ethernet port has established a
valid network connection
Blinking
Ethernet port is in an active
network status
OFF
Ethernet port has not established
valid network connection
【Logging in to WEB Interface】
This device supports WEB management and configuration.
Computer can access the device via Ethernet interface. The
way of logging in to device’s configuration interface via IE
browser is shown as below:
Configure the IP addresses of computer and theStep 1
device to the same network segment, and the
network between them can be mutually accessed
Enter device’s IP address in the address bar of theStep 2
computer browser.
Enter device’s username and password in the loginStep 3
window as shown below.

Click “Login” button to login to the WEB interface ofStep 4
the device.
Note:
The default IP address of the device is “192.168.1.254”.
The default user name and password of the device are
“admin”.
If the username or password is lost, user can restore it to
factory settings via device DIP switch or management
software; all modified configurations will be cleared
after restoring to factory settings, so please backup
configuration file in advance.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.
【Specification】
Panel
Gigabit SFP
1000Base- X, SFP slot
Gigabit copper port 10/100/1000 Base-T(X)
self-adapting RJ45 port, half/full
duplex self-
adaption or forced
working mode, support MDI/
MDI-X self-adaption
Console port CLI command management
port (RS-232), RJ45
Alarm interface 2-
pin 7.62mm pitch terminal
block, support 1 relay alarm
output
Indicator
Power supply indicator, run
indicator, interface indicator,
alarm indicator
Switch Property
Backplane bandwidth
56G
Packet buffer size
12Mbit
MAC Address Table
16K
Power supply
Input power supply 12~48VDC, support dual power
supply redundancy and
non-polarity
Access terminal blocks
4 pins 7.62mm pitch terminal
blocks
Power Consumption
Model I No-load: 11.04W@48VDC
Full-load: 13.68W@48VDC
Model II No-load: 11.04W@48VDC
Full-load: 14.88W@48VDC
Working Environment
Working temperature
-40~75℃
Storage temperature
-40~85
℃
Working humidity
5%
～
95% (no condensation)
Protection grade
IP40 (metal shell)