3One data ES1008G-8POE-150W-P User manual

ES1008G-8POE-150W-P(220VAC)
Full Gigabit Unmanaged POE
Switch
User manual
Shenzhen 3onedata Technology CO.,Ltd
Address:3/B, Zone 1, Baiwangxin High Technology Industrial
park, Song Bai Road,Nanshan District,ShenZhen,
518055,China
Website:www.3onedata.com
Tel:[phone]
Fax:[phone]
【Introduction】
ES1008-8POE-150W-P(220VAC) is Full Gigabit , 8-port Gigabit
high power (IEEE 802.3at) PoE Switches ，utilizing a compact
factor which can be mounted in a 19-inch rack with rack-mounting
kits or placed on desktop.
With data and power supported by one unit, the POE Switch shall
reduce cables and eliminate the need for dedicated electrical outlets
on the wall ,ceiling or any unreachable place. Auto POE detection
and Plug and play installation makes the Gigabit POE Switch easy
to use and with clear LED indicators to tell the working condition.
【Packing List】
Please check the packaging and accessories by your first using.
POE Switch ×1
User’s Guide ×1
Certificate of quality ⅹ 1
Warranty card ⅹ 1
【Features】
Compatible with both IEEE802.3at(30W) and IEEE802.3af
(15.4W)
Automatically detect and supply power to IEEE802.3at and
IEEE802.3af compliant powered devices(PDs)
Advanced SAFC function, only supply power to IEEE
802.3af/at compliant PDs, no worry about damaging other private
standard POE devices or devices without POE function
Support port power supply prioritization, guarantee the
continuous power supply of key nodes
Up to 100m network cable transmitting distance
Built-in PSE power supply module, plug-and play design,
easy to install
High security performance defending against power surge
Support short-circuit protection function
Energy-saving green design, support auto-switch to standby
mode and auto-detect cable length
【Panel Layout】
Front panel
Back panel
1. The corresponding interface LED indicator
2. System Indicator
3. Power Indicator
4. 10Base-T /100Base-T/1000Base-TX port
5. Power input socket and switch
【Dimension】
【Power Input】
The POE Switch provides three power socket rear panel Used in
the AC power input (220 VAC)
【Communication Connector】
10/100/1000BaseT(X) Ethernet port

10Base-T/100Base-TX/1000 Base-TX Ethernet port use in
front panel, It is RJ45 port, the PIN define of RJ45 is as follows:
connection adopt UTP or STP, the distance is no more than 100m,
1000Mbps use cat5e, 100Mbps use cat5, 10Mbps use cat3,4, 5.
RJ45 port support MDI/MDI-X self-adaption. In (MDI),
PIN1, 2, 3, 4, 5, 6, 7, 8 connect corresponding, in (MDI-X)
PIN1→3, 2→6, 3→1, 6→2, 4→7, 5→8, 7→4, 8→5. In
MDI/MDI-X, 1000 Base-TX PIN define is as follows:
Note：“TX±”Transmit Data±，“RX±”Receive Data±，“—”Not Use。
MDI (straight-through cable):
MDI-X (Cross over cable)
MDI/MDI-X auto connection makes switch easy to use for
customers without considering the type of network cable.
【LED Indicator】
The POE Switch indictor light on the front panel. the function of
each LED is described in the table as below.
LED
Indicat
or
Description
PWR
ON
Power connection regularly
OFF
Power supply have no connection or
unwonted
Sys
Blinking
Software running in the CPU
Destroy/
normall
y on
The software runs abnormally in the CPU
Link/A
CT
ON
Established effective network connection
Flashing
Network in activity statues
OFF
Did not established effective network
connection
Yellow
The 10/100M ports auto-negotiate
connected
Green
The 1000Mbps ports auto-negotiate
connected
POE
ON
The POE function works
Flashing
The POE ports failed to work or the PDs
are overloaded
【Installation】
Operation Cautions
1) Don’t stock the device in damp environment or near
water, to avoid water or moisture penetrating into the
inner device.
2) Don’t put the device on a unstable box or desk, the
device will get damaged from falling.
3) Please check and make sure the operation voltage is
meet the voltage standard marked on the device surface
before the next steps.
4) Please use a grounded three-hole power socket in the
rack or desk mounting, to mitigate damage caused by
electro-static discharge or lightning stoke.
5) Keep the device far from heat sources, strong power
radio transmitters and radar transmitters.
6) Similar with other electrical products, the semiconductor
chip in device will get damaged when open and shut off
the power frequently. Please restart the device 3~5
seconds(or longer) after the power is shut off.
7) Please pull out the power plug before cleaning the
device. Don’t wipe the device with wet cloth or clean the
device with liquid.
8) To guarantee a long operation life, the device can only
be used in indoor and in ventilated & dry environment.
And to get a good heat dissipation, please reserve a
space over 10CM around the device.
Rack Mounting
PIN
10/100Mbps
1000Mbps
MDI
MDI-X
MDI
MDI-X
1
TX+
RX+
BI_DA+/TX+
BI_DB+/RX+
2
TX-
RX-
BI_DA-/TX-
BI_DB-/RX-
3
RX+
TX+
BI_DB+/RX+
BI_DA+/TX+
4
-
-
BI_DC+/—
BI_DD+/—
5
BI_DC-/—
BI_DD-/—
6
RX-
TX-
BI_DB-/RX-
BI_DA-/TX-
7
-
-
BI_DD+/—
BI_DC+/—
8
-
-
BI_DD-/—
BI_DC-/—
1 8

Note: Generally, switches with 8 ports or more ports can
be mounted in a standard 19-inch equipment rack defined
by Electronic Industries Association(EIA).
1) Please first attach the two L-shaped brackets to the
device sides, using the screws provided in the bracket
mounting kit.
2) Mount the device in the rack, using rack mounting
screws( not provided).
Making power connection
POE switches is designed for AC 90～264V/50～60Hz Power
Supply. We advise to adopt a one-phase 3-wire power socket with
neutral point joint or multifunctional computer power socket.
Please make sure there are no problems on power supply,
connection and grounding before you start operating the POE
devices, or the devices will get damaged.
Connecting Instruction：
1) Connect one end of power cord into the AC power
socket of POE device rear panel, and then connect the
other end to the external AC power supply socket.
2) Check the “Power” indicator on the POE device front
panel, the LED will be on if successfully connected.
【Specification】
Technology:
Standard and Protocols: IEEE 802.3af，Power Over Ethernet、
IEEE 802.3at，Power Over Ethernet Plus
IEEE 802.3u， 100BASE-TX、 IEEE 802.3ab， 1000 BASE-T、 IEEE
802.3x，Full-Duplex Flow Control、IEEE 802.3az，EEE(Energy
Efficient Ethernet)
POE Standard: IEEE802.3af/at
Port Flow control： Back-pressure traffic control under Half-Duplex
mode，IEEE 802.3x traffic control under Full-Duplex mode
Interface:
RJ45: 10 /100/1000Base-TX auto speed control, Half/full duplex
and MDI/MDI-X auto detect
PoE Pin-out: 1/2(+)，3/6(-)；Customized 4/5(+),7/8(-)
Exchange Properties:
100M forwarding rate: 1488095pps
100M forwarding rate: 148809pps
10M forwarding rate：14880pps
Transmit type: Full wire-speed storage and forwarding
MAC address: 8K，Support auto-update, two-way learning
Switching Capacity：≥16Gbps
Spanning Tree: Spanning Tree Protocol
Rapid Spanning Tree Protocol(RSTP)
Port Flow Control: Back-pressure traffic control under Half-Duplex
mode ,IEEE 802.3x traffic control under Full-Duplex mode
Port Rate Restriction: Port-based ingress or egress rate limiting
Jumbo Frame: Maximum support 9216Byte
Indicator light:
Interface light: Link/Act，POE Status
Power light: PWR
Power:
Input Power Supply: 90～264VAC/50～60Hz/150W
Working Environment:
Working Temperature: -20~50°C
Storage Temperature: -40~70°C
Operation Humidity:10%～90%(non-condensing)
Storage Humidity:5%～95%(non-condensing)
Mechanical Properties:
Weight: <1.5Kg
Dimensions（L×W×H）:280×180×44mm
Energy Saving: Comply with “EEE” Energy Efficient Ethernet
Warranty:
Warranty time: 3 years