3One data IES615-2DI Series User manual

IES615-2DI series
Managed Industrial Ethernet switch
User manual
Version 1.0.0, Aug. 2017
www.3onedata.com

User Manual
- 1 -
IES615-2DI series user manual
Statement
Copyright Notice
Information in this document is reserved by 3onedata Co., Ltd. Reproduction and
extract without permission is prohibited.
Trademarks Notice
, and is registered trademarks of
3onedata Co., Ltd. All other trademarks or registered marks in this manual belong
to their respective manufacturers.
Agreement
As the product version upgrades or other reasons, this document is subject to
change without notice. Unless other agreement, this document only as a guide to
use. All statement, information and suggestion in this document, without warranty
of any kind, either expressed or implied.
Revision History
Version No.
Date
Reason
V1.0.0
August, 2017
Creating Documents
Notes
In reading this manual, please pay attention to the following symbols,
Information necessary to explain
Special attention

User Manual
- 2 -
Content
CHAPTER 1 SUMMARIZE......................................................................................................................... 1
1.1 Introduction........................................................................................................................................... 1
1.2 Features ............................................................................................................................................... 1
CHAPTER 2 HARDWARE DESCRIPTION ............................................................................................... 2
2.1 Panel design......................................................................................................................................... 2
2.2 Power supply input............................................................................................................................... 3
2.3 Relay connection.................................................................................................................................. 3
2.4 DIP switch............................................................................................................................................. 3
2.5 Communication port............................................................................................................................. 3
2.6 Serial port connection........................................................................................................................... 5
2.7 LED Indicator........................................................................................................................................ 6
2.8 Installation ............................................................................................................................................ 6
Chapter 3Appearance and Dimension...................................................................................................... 8
3.1 Appearance .......................................................................................................................................... 8
3.2 Dimension............................................................................................................................................. 8
CHAPTER 4 PACKLING LIST ................................................................................................................... 9
CHAPTER 5 Network Configuration ........................................................................................................ 10
5.1 Modify IP address............................................................................................................................... 10
5.2 Login Web Server................................................................................................................................11
5.3 Introduction configure interface...........................................................................................................11
5.3.1 Main menu ............................................................................................................................... 12
5.4 System Status............................................................................................................................. 13
5.4.1 System information.............................................................................................................. 13
5.4.2 Port information ................................................................................................................... 14
5.5 Serial Server....................................................................................................................................... 14
5.5.1 COM Settings........................................................................................................................... 14
5.5.2 Configure working mode.......................................................................................................... 17
5.5.3 COM Information...................................................................................................................... 20
5.6 Port Configuration .............................................................................................................................. 20
5.6.1 Port Settings............................................................................................................................. 20
5.6.2 Bandwidth Management.......................................................................................................... 22
5.7 L2 Features........................................................................................................................................ 23
5.7.1 VLAN........................................................................................................................................ 23
5.7.2 IGMP snooping........................................................................................................................ 27
5.7.3 Static Multicast......................................................................................................................... 27
5.8 QOS.................................................................................................................................................... 28
5.8.1 QOS Classification................................................................................................................... 28
5.8.2 COS.......................................................................................................................................... 29
5.8.3 TOS (DSCP) ............................................................................................................................ 30
5.9 Redundancy....................................................................................................................................... 31
5.9.1 Port Trunking............................................................................................................................ 31
5.9.2 Rapid Ring ............................................................................................................................... 32
5.9.2.1 Ring V3 single ring configuration...................................................................................... 34
5.9.2.2 Ring V3 dual ring configuration......................................................................................... 35
5.9.2.3 Ring V3 Coupling Configuration........................................................................................ 35
5.9.2.4 Ring V3 Chain Configuration............................................................................................. 36
5.9.2.5 Ring V3 Dual_homing Configuration................................................................................. 37
5.9.3 Rapid Spanning Tree Protocol (RSTP) ................................................................................... 39
5.10 Access Profile................................................................................................................................... 41
5.10.1 Login Settings........................................................................................................................ 41

User Manual
- 3 -
5.11 Remote monitoring........................................................................................................................... 42
5.11.1 SNMP management............................................................................................................... 42
5.11.2 Relay Alarm............................................................................................................................ 44
5.12 Traffic Statistics................................................................................................................................ 45
5.12.1 RX frame statistics................................................................................................................ 45
5.12.2 TX frame statistics................................................................................................................. 46
5.13 Diagnosis.......................................................................................................................................... 46
5.13.1 Mirror...................................................................................................................................... 46
5.14 Basic settings................................................................................................................................... 47
5.14.1 Device address...................................................................................................................... 47
5.14.2 System identification............................................................................................................. 49
5.14.3 System File Upgrade ............................................................................................................. 50
5.14.4 Logout.................................................................................................................................... 51
Appendix 1 Glossary table ....................................................................................................................... 52
Appendix 2 Default factory....................................................................................................................... 54
Appendix 3 Treatment of common problem............................................................................................. 55

User Manual
1
CHAPTER 1 SUMMARIZE
1.1 Introduction
The IES615-2DI (3IN1) series is a managed industrial Ethernet switch that provides 5 Fast Ethernet
ports, 2 three-in-one RS-232/485/422 serial ports. The electrical port supports 10 / 100M adaptive, MDI /
MDI-X adaptive. Power supply supports 12 ~ 48VDC input.
The -40~75℃operating temperature range to adapt to the harsh working environment. Rail mounting
features to meet the needs of industrial sites, the user's Ethernet equipment to provide a reliable, fast
solution.
1.2 Features
Supports IEEE802.3, IEEE802.3u, IEEE 802.3x, IEEE802.1Q, IEEE802.1p, IEEE802.1D,
IEEE802.1W
Supports 5-port Fast Ethernet, copper ports and optical fiber ports optional
Supports 2-Port optical isolation of the three-in-one (RS-232/485/422) serial server
Support based on socket application access
Supports TCP Server, TCP Client, and UDP based mode; TCP Server and UDP advanced mode
SW-Ring ring network patent technology (Fault recovery time<20ms)
Support RSTP, way exchange time<1s
Supports static multicast, QoS function
Supports Port based VLAN and IEEE 802.1Q VLAN
Industrial grade design, -40~75°C work temperature
IP40 protection grade, DIN-Rail mounting
No fan design

User Manual
2
CHAPTER 2 HARDWARE DESCRIPTION
2.1 Panel design
Vertical view and Bottom view Rear view
Front view
IES615-2DI (3IN1) IES615-1F-2DI (3IN1) IES615-2F-2D (3IN1)
1. Ground screw
2. 2-pin terminal block for relay output
3. Console port
4. 4-pin terminal block for power input
5. DIP switches for default factory
6. Screw holes for wall mounting kit
7. DIN-Rail mounting kit
8. Power LEDs (PWR1, PWE2)
9. System running LED
10. Relay alarm LED
11. Serial port transmits and receives data LEDs
12. RS-232/485/422 serial ports
13. Ethernet port Link/ACT LEDs
14. 10/100Base-T(X) Ethernet ports
15. 100Base-FX fiber ports

User Manual
3
2.2 Power supply input
The switch have redundant power input, provides one terminal block (4 bits) for PWR1 and PWR2 input.
The redundant power can be used single and used two self-governed power to supply to the system,
PWR1 and PWR2 input at the same time, when neither of these two power fails, the other power acts as
a backup, and automatically supplies power needs, ensure running Ethernet reassuring. Voltage input
range is 12～48VDC (terminal block defined as: V1-、V1+、V2-、V2+).
2.3 Relay connection
The relay owns two contacts of the terminal block on the top panel of the Switch series. It is used to
detect both power failure and port failure. The open circuit state in normal non alarm state, when there is
any alarm information to the closed state. The relay can external alarm lights or alarm buzzer or external
switch signal acquisition device in order to timely notify operators when an alarm occurs.
2.4 DIP switch
Top panel provided 4 bits DIP switch to do function configure (OFF is default factory). 1 and 4 are
reserved. 2 is recovery default factory. 3 is upgrade. Please power off and power on when you change
the status of DIP switch.
2.5 Communication port
10Base-T /100Base-TX Ethernet port
10Base-T/100Base-TX Ethernet port is located on front panel and the type is RJ45. The pinout of RJ45
port connects to UTP or STP. The distance is not more than 100m. 100Mbps Ethernet connector takes
120Ωof UTP 5, 10Mbps Ethernet connector takes 120Ω of UTP 3, 4, 5.
RJ45 port supports automatically MDI/MDI-X connection. It can connect PC, Server, Converter and
HUB .Corresponding connection of Pin 1,2,3,6 is like this: 1→3, 2→6, 3→1, 6→2. The definition of Pin is
displayed as below.

User Manual
4
Information necessary to explain:
Note: ―TX±‖Transmitting data±, ―RX±‖receiving data±, ―—‖no use
MDI(straight-through cable):
MDI-X(Cross over cable):
100Base-FX fiber port
100Base-FX port works with full-duplex, SM or MM SC/ST/FC optional. The fiber port must be used in
pair, TX (transmitting) port connects remote switch‘s RX (receive) port; RX (receiving) port connect
remote switch‘s TX (transmitting) port.
Suppose: If you make your own cable, we advise to label the two sides of the cable with the same
letter (A-to-A and B-to-B, shown as below, or A1-to-A2 and B1-to-B2).
PIN
MDI
MDI-X
1
TX+
RX+
2
TX-
RX-
3
RX+
TX+
6
RX-
TX-
4, 5, 7, 8
—
—
1 8

User Manual
5
2.6 Serial port connection
Serial port:
The RS-232/485/422 serial port uses 5-pin terminal block as shown below.
PIN
RS-232
RS-485
RS-422
1
-
D+
T+
2
TX
D-
T-
3
GNS
GND
GND
4
-
-
R+
5
RX
-
R-
12345

User Manual
6
2.7 LED Indicator
System Indication LED
Led
State
Description
P1
ON
PWR1 is connected and operates properly.
OFF
PWR1 is not connected or operates abnormally.
P2
ON
PWR2 is connected and operates properly.
OFF
PWR2 is not connected or operates abnormally.
RUN
ON/OFF
The system is running abnormally.
Blinking
The system is running properly.
ALM
ON
When the alarm is enabled, power or the port‘s link is inactive.
OFF
Power and the port‘s link is active, the alarm is disabled.
1~5
ON
The Ethernet port is connected properly.
Blinking
The Ethernet port is connected and data is being transmitted.
OFF
The Ethernet port is not connected properly.
TX(1~2)
Blinking
The serial port is transmitting data
OFF
No serial data transmission
RX(1~2)
Blinking
The serial port is receiving data
OFF
No serial data received
2.8 Installation
Before installation, confirm that the work environment meet the installation require, including the power
needs and abundant space. Whether it is close to the connection equipment and other equipment are
prepared or not.
1. Avoid in the sunshine, keep away from the heat fountainhead or the area where in intense EMI.
2. Examine the cables and plugs that installation requirements.
3. Examine whether the cables be seemly or not (less than 100m) according to reasonable scheme.
4. Power: Redundant, dual 12-48VDC power input
5. Environment: working temperature: -40～75℃
Storage Temperature: -40～85℃
Relative humidity 5%～95%
DIN Rail Installation
In order to use in industrial environments expediently, the switch adopt 35mm DIN-Rail installation, the
installation steps as below:
1.Examine the DIN-Rail attachment
2.Examine DIN-Rail whether be firm and the position is suitability or not.
3.Insert the top of the DIN-Rail into the slot just below the stiff metal spring.
4.The DIN-Rail attachment unit will snap into place as shown below.

User Manual
7
Wiring Requirements
Cable laying need to meet the following requirements,
1. It is needed to check whether the type, quantity and specification of cable match the requirement
before cable laying;
2. It is needed to check the cable is damaged or not, factory records and quality assurance booklet
before cable laying;
3. The required cable specification, quantity, direction and laying position need to match construction
requirements, and cable length depends on actual position;
4. All the cable cannot have break-down and terminal in the middle;
5. Cables should be straight in the hallways and turning;
6. Cable should be straight in the groove, and cannot beyond the groove in case of holding back the
inlet and outlet holes. Cables should be banded and fixed when they are out of the groove;
7. User cable should be separated from the power lines. Cables, power lines and grounding lines
cannot be overlapped and mixed when they are in the same groove road. When cable is too long, it
cannot hold down other cable, but structure in the middle of alignment rack;
8. Pigtail cannot be tied and swerved as less as possible. Swerving radius cannot be too small (small
swerving causes terrible loss of link). Its banding should be moderate, not too tight, and should be
separated from other cables;
9. It should have corresponding simple signal at both sides of the cable for maintaining.

User Manual
8
Chapter 3 Appearance and Dimension
3.1 Appearance
IES615-2DI(3IN1) IES615-1F-2DI(3IN1) IES615-2F-2DI(3IN1)
3.2 Dimension
The series of products are the same size, but their types of interfaces are different. Unit (mm)

User Manual
9
Chapter 4 Packing List
Please check the packaging and accessories by your first using. Please inform us or our distributor if
your equipments have been damaged or lost any accessories, we will try our best to satisfy you.
Description
Quantity
Industrial Ethernet switch
1
User manual
1
Documentation and software CD
1
Warranty card
1
Certificate of quality
1
DIN-Rail mounting kit
1

User Manual
10
Chapter 5 Network Configuration
5.1 Modify IP address
The switch default address is: 192.168.1.254, subnet mask is: 255.255.255.0. When entering into the
switch Web interface through internet explorer, the IP address of the switch and PC must be in the same
Local Area Network.
You can modify PC's or the switch's IP address to make sure that they are in the same Local Area
Network. Operating process can follow method 1 or method 2 as below,
Method 1: Modify PC's IP address
Click Start->Control panel->network connections->Local area Connection->Properties->Internet
protocol(TCP/IP)Setting PC‘s IP address: 192.168.1.X (X is less than 254, from 2 to 253).
Click ―OK‖, IP address modifies successfully.
(Figure 5.1.1)
Method 2: Modify the switch's IP address through Blue_eyes manager software.
Install Blue_eyes manager software on the PC.
Enter into Blue_eyes management interface, click "Search" to search the device.
After searching the device, move mouse to the device, click right key, modify the device's IP
address,
Please make sure the device and PC in the same LocalArea Network.
This configuration example does not use the Advanced button in the last picture. In one and the same network card
allows the use of multiple IP pseudo-address when use the advanced configuration of the IP address, at which
does not change the original address can still access the switch device. But in the IGMP polling and IEEE 802.1x
polling windows system cannot handle correctly, Unix-like system does not have this problem. The advanced users
have to pay attention to this issue.
Configuration preparing

User Manual
11
1. The lowest requirement for user's computer is as below:
Install operating system (Windows XP/2000/7/8,etc)
Install Ethernet card
Install Web explorer (IE6.0 or higher version)
Install and start TCP/IP protocol
2. Establish the correct network configuration
The default management IP address of the switch: 192.168.1.254, subnet mask as: 255.255.255.0.
Before access to the configuration interface, the computer's IP address and the switch must be
configured in the same subnet (IP address configuration, please refer to "5.1") if need local configuration;
Computers and switches must be routed reach if for remote configuration.
5.2 Login Web Server
Please type in the default IP of switch on the browser‘s address bar, and then will pop-up a window by
clicking the ―enter‖ key which shows you have to enter your user name and password. The default
username and password is ―admin‖. You can enter your username and password 3 times if you found the
username and password is incorrect. If the 3 input error, the browser will display a "Access denied" error
message. Refresh the page and then enter the correct user name and password, log on to the Web
Server, it will recommend to modify the user name and password. Please contact our customer service
center if you have more questions.
(Figure 5.2.1)
The default username and password is [admin], case sensitive for this series. The default password
is with administrator privileges.
:
Before entering the switch Web Server, you must delete temporary IE files, and clear IE history, or perhaps because
IE cookies due to an unknown error.
The user name and password are case sensitive. Such as unclear devices IP address, can be obtained through the
Blue_eyes management software search. (attached)
5.3 Introduction configure interface
The Web configuration page is divided into: 1 title, 2 main menu, 3 configuration menu bar area three
parts. Click the menu item in the menu bar, you can enter the corresponding configuration interface,
display device state information and data configuration. As shown in Figure 5.3.1.

User Manual
12
(Figure 5.3.1)
5.3.1 Main menu
Menu Introduction:
Main Menu
Tag
Function
System Status
System information
Display device information and port information such
as software version, IP address, etc.
Serial Server
COM Settings
Serial parameter and Working mode configuration
COM Information
Display incorrect data statistics and connection
information that send by serial port.
Port
Configuration
Port settings
Display and configure information of each port: such
as connection status, configuration modes, flow status
etc.
Bandwidth
management
Set the maximum rate of the input/output packets for
port.
L2 feature
VLAN
Displays the current list of 802.1Q VLAN, configure
and manage 802.1Q VLAN.
IGMP snooping
Display port-based VLAN list, and to configure and
manage port-based VLAN.
Static Multicast
Configure the static multicast MAC address and its
corresponding port.
QOS
QoS classification
Configure the QOS queue mode, QOS
implementation and port default priority.

User Manual
13
Main Menu
Tag
Function
Cos Mapping
Configure the meaning of COS value.
ToS/DiffServ Mapping
Configure the DSCP priority.
Redundancy
Port Trunking
Configure port trunking group.
Rapid Ring
Configure the rapid ring network port and type.
RSTP
Configure the parameters of RSTP.
Access control
Login Settings
Configure different permissions for the user name and
password.
Remote
Monitoring
SNMP
Set up a simple configuration
Relay Warning
Set relay alarm type
Port Statistics
Frame statistics
Diagnosis
Mirror
Configure the mirror port and mirrored port.
Basic Settings
Network & Reboot
Device IP, gateway, DNS and Device reboot
System Identification
Model, Name, Description and Contact information.
System Log
Log information.
System File update
Software upgrade, acquire, preserve or restore the
switch configuration.
Web Timeout Treatment
The system timeout will cancel the login if the user did not login for a long time (The configuration of this
login will be remained in the Web interface).
If user doesn't operate the Web interface for a long time, The system will be canceled this login.(but configuration
change made in this login will be saved in Web configuration interface.). If the user wants to do any operating on
Web configuration interface again, the system will remind user and returns to the login dialog box. Users need to
log in again if operating is needed. The timeout time is 300s.
5.4 System Status
Enter the correct user name and password that the normal the switch WEB interface display
information about the state of the system, including: the main menu, equipment information, port
information, and displayed in the upper left corner of the page's 3onedata Technology Co., Ltd. the
registered trademark, the upper right corner of display is the current time, as shown in figure 5.4 show:
(Figure 5.4)
5.4.1 System information
Equipment information mainly display basic information, the switch include: equipment name,
description of the equipment, hardware version number, firmware version, the switch of MAC address.
As shown in figure 5.4.1

User Manual
14
(Figure 5.4.1)
5.4.2 Port information
The switch a total of 5 ports, ports can confirm whether the port with the equipment complies with the
information bar. Equipment at work, via the port status of the port information in the status view, for
example in the figure below you can see port 3 is LINK and port connection status as FULL, speed is
100M and port type for the TX(RJ45). As shown in Figure 5.4.2.
LINK:Indicates that the port is in a connected state;
LOS:Indicates that the port is not connected;
FULL:Indicates that the port State is full duplex;
HALF:Indicates that the port State is half-duplex (if the ports are not connected, the port status is
HALF);
(Figure 5.4.2)
5.5 Serial Server
5.5.1 COM Settings
Server configuration includes the serial port configuration and mode of operation of the configuration
parameters
Serial port configuration menu
Optional data
Description
Serial port working mode
RS-232 full duplex/RS-422 full
duplex/RS-485 half duplex
Serial work mode
Baud rate(bps)
300-115200(10pcs band rate
optional)
Baud rate choice
Parity
None, Even, Odd, Mark, Space
Checkout choice
Data bits(bits)
5,6,7,8
The parameter of serial

User Manual
15
Stop bits (bits)
1,1.5,2
The last of the data package
Max frame space(bytes)
1-1460
The length of frame from
serial data to Ethernet data.
Character delay(ms)
1-500
The time space from serial
data to Ethernet data
Enter into the switch WEB interface, knock [Serial Server/COM settings]; please choice necessary
configuration in drop down list, the serial configuration interface is as follows:
(Figure 5.5.1)
Configuration option: [Baud rate], [Parity], [Data Bits], [Stop Bits], [Max Frame Space], [Character Delay]
and [COM mode], the explaining is as follows:
[Baud rate]
It is a parameter to check the communication speed. It shows to transfer how many bits in 1 second.
For example, 300 baud rate means have 300 bits transferred in 1 second.
[Parity]
Parity bits: It is a simple method to checkout fault in serial communication, have 4 types: Even, Odd,
Mark, Space
[Data Bits]
It is a parameter to check the actual data bits in communication.
When PC send a Packet, actual data is not 8 bits, the standard is 5, 6, 7, 8.
[Stop Bits]
The last bit of the single Packet. Typical value is 1, 1.5 and 2 bit.
When a data bit is 5, stop bit 1.5 and 1 option. When a data bit is 6, 7, 8, stop bit 1 and 2 option.
[Max frame space]
The frame length that serial interface data convert into Ethernet data, within the range of setting time,
it forward when data is equal to or longer than the setting frames.
Available setting value ranged from1 to 1460.
[Character Delay]
The wait time when serial interface send data do not 1 data frames. If up to this time and do not
have data, then send automatic. Can configure 1-500.
[COM mode]

User Manual
16
RS-232, RS-485, RS-422 serial port Optional.