Aaeon EMB-CV1 series User manual

Industrial Motherboard EMB-CV1 series
EMB-CV1 series
Manual 5th Ed.
November 2015

Industrial Motherboard EMB-CV1 series
Copyright Notice
This document is copyrighted, 2015. All rights are reserved. The
original manufacturer reserves the right to make improvements to
the products described in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated, or
transmitted in any form or by any means without the prior written
permission of the original manufacturer. Information provided in this
manual is intended to be accurate and reliable. However, the
original manufacturer assumes no responsibility for its use, or for
any infringements upon the rights of third parties that may result
from its use.
The material in this document is for product information only and is
subject to change without notice. While reasonable efforts have
been made in the preparation of this document to assure its
accuracy, the original manufacturer assumes no liabilities resulting
from errors or omissions in this document, or from the use of the
information contained herein.
The original manufacturer reserves the right to make changes in the
product design without notice to its users.
i

Industrial Motherboard EMB-CV1 series
Acknowledgments
All other products’ name or trademarks are properties of their
respective owners.
AMI is a trademark of American Megatrends Inc.
CompactFlash™is a trademark of the Compact Flash
Association.
Intel®and Atom™are trademarks of Intel®Corporation.
Microsoft Windows®is a registered trademark of Microsoft
Corporation.
ITE is a trademark of Integrated Technology Express, Inc.
IBM, PC/AT, PS/2, and VGA are trademarks of International
Business Machines Corporation.
SoundBlaster is a trademark of Creative Labs, Inc.
Please be notified that all other products’ name or trademarks
not be mentioned above are properties of their respective
owners.
ii

Industrial Motherboard EMB-CV1 series
Packing List
(Standard, not bulk pack)
Before you begin installing your card, please make sure that
the following materials have been shipped:
1 Cable Set (SATA Cable, SATA Power Cable)
1 Metal I/O Bracket
1 Product CD
1 Industrial Motherboard
If any of these items should be missing or damaged, please
contact your distributor or sales representative immediately.
iii

Industrial Motherboard EMB-CV1 series
Contents
Chapter 1 General Information
1.1 Features .................................................................... 1-2
1.2 Specifications............................................................ 1-3
Chapter 2 Quick Installation Guide
2.1 Safety Precautions ..................................................2-2
2.2 Location of Connectors and Jumpers ......................2-3
2.3 Mechanical Drawing ................................................ 2-4
2.4 List of Jumpers ........................................................2-6
2.5 List of Connectors ..................................................... 2-7
2.6 Setting Jumpers .......................................................2-9
2.7 AT/ATX Mode Selection (ATMODE) .....................2-10
2.8 Clear COMS (CLRTC).............................................2-10
2.9 COM2 External Power Selection (DIGITALREFENCE)
.......................................................................................2-10
2.10 LVDS Panel Power Selection (LVDS_VDD_SEL) 2-10
2.11 LVDS Brightness Control Type Selection
(L_BRIGHTNESS).........................................................2-10
2.12 LVDS function Enable (LVDS_SWITCH)..............2-11
2.13 LVDS Panel Backlight Power Selection
(LCD_POWER_SEL) ....................................................2-11
2.14 Watchdog Timer Function Switch (WDT)..............2-11
iv

Industrial Motherboard EMB-CV1 series
2.15 +12V AUX Power Connector (CON2)...................2-11
2.16 CPU/SYSTEM FAN Connector (CPU_FAN/CHA_FAN)
.......................................................................................2-11
2.17 COM3/COM4/COM5 RS232 Serial Port PIN HEADER
(COM3/COM4/COM5)...................................................2-12
2.18 GPIO/SM BUS/COM2/ COM2 External Power
Selection (DIGITALREFENCE).....................................2-12
2.19 COM2 RS-232/422/485 connector........................2-13
2.20 Front Panel Pin Header (F_PANEL).....................2-13
2.21 PS/2 Keyboard/Mouse Connector (KB/MS)..........2-13
2.22 LVDS Panel Power Connector (LCD_POWER) ...2-14
2.23 Parallel Port Connector (LPT)...............................2-14
2.24 LVDS Panel Connector (LVDS) ............................2-15
2.25 Serial ATA power Connector (SATA_PWR1).......2-16
2.26 USB 5 & 6 PIN HEADER (USB56)........................2-16
2.27 USB 7 PIN HEADER (USB7) ..............................2-17
Chapter 3 AMI BIOS Setup
3.1 System Test and Initialization. .................................. 3-2
3.2 AMI BIOS Setup........................................................3-3
Chapter 4 Driver Installation
4.1 Installation………………………………………..……..4-3
v

Industrial Motherboard EMB-CV1 series
Appendix A Programming The Watchdog Timer
A.1 Programming ............................................................A-2
A.2 ITE8783 Watchdog Timer Initial Program .………....A-6
Appendix BMating Connector
B.1 List of Mating Connectors and Cables......................B-2
vi

Industrial Motherboard
EMB-CV1 series
Chapter 1 General Information 1- 1
General
Information
Chapter
1

Industrial Motherboard
EMB-CV1 series
Chapter 1 General Information 1-2
1.1 Features
Onboard Intel®Atom™ D2550 Processor
Intel®NM10
Intel®Graphics Media Accelerator 3600 Supports DirectX
10, OpenGL 3.0
DDR3 800/1066 SO-DIMM x 2, Max. 4GB
VGA, 18/24-bit LVDS, DVI, Dual Independent Display
Dual Gigabit Ethernet
COM x 5 (RS-232 x 4, RS-232/422/485 x 1)
USB2.0 x 6, SATA 3Gb/s x 2
PCI-Express [x1] x 1, Full-size Mini Card + SIM slot x 1
(m-SATA option, if use m-SATA, one of SATA port and
Mini Card + SIM Card will be disable)
5.1 CH Audio Channel

Industrial Motherboard
EMB-CV1 series
Chapter 1 General Information
1-3
1.2 Specifications
System
Processor
Intel®Atom™D2550 Dual Core
Processor, up to 1.86GHz
System Memory
204-pin single channel DDR3
800/1066 DIMM x 2, Max. 4GB
(When you install only one
memory module, install it on
DIMM A2 slot)
Chipset
Intel® NM10
I/O Chipset
ITE IT8783F
Ethernet
Realtek 8111E for
10/100/1000Base-TX, RJ-45 x 2
BIOS
AMI BIOS, 32MB ROM
Wake On LAN
Yes
Watchdog Timer
System reset: 1~255 steps
programmable
H/W Status Monitoring
Supports Power Supply Voltage,
Fan Speed, and Temperature
Monitoring
Expansion Interface
PCI-Express[x1] x 1,
Full-size Mini Card + SIM Card
slot x 1 (m-SATA option)
Battery
Lithium battery
Power Requirement
DC 12V
(selectable AT/ATX mode)
Board Size
6.7”(L) x 6.7”(W)
(170 mm x 170 mm)
Gross Weight
1.1 lb (0.5 Kg)

Industrial Motherboard
EMB-CV1 series
Chapter 1 General Information 1-4
Operating Temperature
32˚F~ 140˚F (0˚C ~ 60˚C)
Storage Temperature
-40˚F~ 185˚F (-40˚C ~ 85˚C)
Operating Humidity
5%~95% relative humidity,
non-condensing
Display
Chipset
Intel®Graphics Media Accelerator
3650
Resolution
Up to 1440x900 18/24-bit
LCD Interface
18/24-bit LVDS
Video Interface
VGA x 1, DVI-D x 1
I/O
Storage
SATA x 2 (support AHCI mode)
(if use m-SATA, one SATA port
will be disable)
Serial Port
RS-232 x 4, RS-232/422/485 x 1
(RS-422/485 is selectable by
BIOS)
Parallel Port
STD/SPP/EPP
USB
USB2.0 x 6
(5x2 pin header for internal x 2,
onboard Type A connector x 4)
Digital I/O
Supports 8-bit (Programmable)
PS/2 Port
Keyboard/ Mouse x 1
Audio
Line-in, Mic-in, Line-out

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 1
Quick
Installation
Guide
Chapter
2

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 2
2.1 Safety Precautions
Always completely disconnect the power cord
from your board whenever you are working on
it. Do not make connections while the power is
on, because a sudden rush of power can
damage sensitive electronic components.
Always ground yourself to remove any static
charge before touching the board. Modern
electronic devices are very sensitive to static
electric charges. Use a grounding wrist strap at
all times. Place all electronic components on a
static-dissipative surface or in a static-shielded
bag when they are not in the chassis

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 3
2.2 Location of Connectors and Jumpers
NOTE: If choose m-SATA SKU, SATA3G_2 port, mini card and SIM
card slot will be disable.

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 4
2.3 Mechanical Drawing
Component Side

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 5
Solder Side

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 6
2.4 List of Jumpers
The board has a number of jumpers that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's jumpers:
Label
Function
ATMODE
AT/ATX Mode Selection
CLRTC
Clear COMS
DIGITALREFENCE
COM2 External Power Selection
LVDS_VDD_SEL
LVDS Panel Power Selection
L_BRIGHTNESS
LVDS Brightness Control Type Selection
LVDS_SWITCH
LVDS Function Enable
LCD_POWER_SEL
LVDS Panel Backlight Power Selection
WDT
Watchdog Timer Function Switch

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 7
2.5 List of Connectors
The board has a number of connectors that allow you to configure your
system to suit your application.
The table below shows the function of each of the board's connectors:
Label
Function
DC_PWR
+12V Power connector
CON2
+12V AUX Power Connector
CHA_FAN
System FAN Connector
COM3
COM 3 Connector
COM4
COM 4 Connector
COM5
COM 5 Connector
CON1
SIM Card Socket
CPU_FAN
CPU FAN Connector
DIGITALREFENCE
GPIO/SM BUS/COM2/ COM2 External Power
Selection
F_PANEL
Front Panel Pin Header
KB/Ms
PS/2 Keyboard / Mouse Connector
LCD_POWER
LVDS Panel Power Connector
LPT
Parallel Port Connector
LVDS
LVDS Panel Connector
PCIEX1_1
PCI-E [x1] Slot
SATA_PWR1
Serial ATA Power Connector
SATA3G_1
SATA 0 Connector
SATA3G_2
SATA 1 Connector

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 8
USB56
USB 5 & 6 Pin Header
USB7
USB 7 Pin Header
WLAN
Mini PCI-E Slot
NOTE: The +12V Power connector (Label: DC_PWR) is lockable Jack
type with screw. Please refer the inner and outer diameter
dimension of connector as below to choose suitable adaptor.

Industrial Motherboard
EMB-CV1 series
Chapter 2 Quick Installation Guide 2 - 9
2.6 Setting Jumpers
You configure your card to match the needs of your application by
setting jumpers. A jumper is the simplest kind of electric switch. It
consists of two metal pins and a small metal clip (often protected by a
plastic cover) that slides over the pins to connect them. To “close” a
jumper you connect the pins with the clip.
To “open” a jumper you remove the clip. Sometimes a jumper will have
three pins, labeled 1, 2 and 3. In this case you would connect either
pins 1 and 2 or 2 and 3.
123
Open Closed Closed 2-3
A pair of needle-nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any change.
Generally, you simply need a standard cable to make most
connections.