ABB CP650-x User manual


Operating Instructions
CP600
Control Panels
CP650-x, CP650-WEB-x
CP660-x, CP660-WEB-x
CP675-x, CP675-WEB-x

Operating Instructions 1 CP600/Issue: 12.2011
Content
Introduction........................................................................................................................3
Before You Start ................................................................................................................4
Safety Notices...........................................................................................................................4
Markups ....................................................................................................................................4
Product Overview ..............................................................................................................5
Standards and Approvals .................................................................................................6
Product Identification...............................................................................................................6
Technical Specifications..........................................................................................................7
Environmental Conditions.......................................................................................................7
Electromagnetic Compatibility (EMC).....................................................................................8
Durability Information..............................................................................................................9
Technical Data .................................................................................................................10
Dimensions.............................................................................................................................11
Installation Environment........................................................................................................12
Applying the Rectangular Gasket.........................................................................................12
Installation Procedure............................................................................................................13
Connections.....................................................................................................................14
PLC Port..................................................................................................................................14
PC/Printer Port........................................................................................................................16
Ethernet Port ..........................................................................................................................16
Power Supply, Grounding and Shielding ......................................................................17
AUX Port...........................................................................................................................18
Battery ..............................................................................................................................19
Cleaning Faceplates........................................................................................................20
Getting Started.................................................................................................................21

Operating Instructions 2 CP600/Issue: 12.2011
System Settings...............................................................................................................22
Dedicated LED Indicators ...............................................................................................24
Unpacking and Packing Instructions.............................................................................25

Operating Instructions 3 CP600/Issue: 12.2011
Introduction
The operational guidelines described below is information which relates to the device, place of employ-
ment, transportation, storage, assembly, use and maintenance.
The products have been designed for use in an industrial environment in compliance with the
2004/108/CE directive.
The products have been designed in compliance with:
EN 61000-6-4
EN 55011 Class A
EN 61000-6-2
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6
The installation of these devices into the residential, commercial and light-industrial environments is al-
lowed only in the case that special measures are taken in order to get the conformity to IEC-61000-6.3.
The products are in compliance with the restrictions on Certain Hazardous Substances (RoHS) Directive
2002/95/EC.
This Operating Instruction describes the main features of the CP600 Control Panels. The Operating In-
structions refers to the following models:
Picture
Type
Description
CP650-x, CP650-WEB-x Operator interface with TFT color 10.4” display
touchscreen
CP660-x, CP660-WEB-x
Operator interface with TFT color 12.1” display
touchscreen
CP675-x, CP675-WEB-x
Operator interface with TFT color 15” widescreen
display touchscreen

Operating Instructions 4 CP600/Issue: 12.2011
Before You Start
Safety Notices
DANGER!
Indicates an imminent risk. It will lead to death or serious injury if not avoided.
WARNING!
Indicates a possible risk. It may lead to death or serious injury if not avoided.
CAUTION!
Indicates a possible risk. It may lead to light or slight injury or material damage if not
avoided.
Markups
Enumeration.
Precondition for an operation instruction or a description.
Operation instruction with one step.
1. Operation instruction with several steps.
Result of an operation.
NOTE
Helpful information with background information or an emphasized notice.
TIP
Application tips or other useful information and suggestions.

Operating Instructions 5 CP600/Issue: 12.2011
Product Overview
The Control Panels combine state-of-the-art features and top performance with an oustanding design.
They are the ideal choice for all demanding HMI applications including factory and building automation.
These Control Panels have been designed to run the PB610 Panel Builder 600 software.
PB610 Panel Builder 600 Runtime included. Full compatibility with PB610 Panel Builder 600.
Full vector graphic support. Native support of SVG graphic objects. Transparency and alpha blend-
ing.
Full object dynamics: Control visibility and transparency, move, resize, rotate any object on screen.
Change properties of basic and complex objects.
Truetype fonts.
Multilanguage applications. Easily create and manage your applications in multiple languages to
meet global requirements. Far East languages are supported. Tools available in PB610 Panel Builder
600 support easy third-party translations and help reducing development and maintenance costs of
the application.
Data display in numerical, text, bargraph, analog gauges and graphic image formats.
Rich set of state-of-the-art HMI features: Data acquisition, alarm handling, scheduler and timed ac-
tions (daily and weekly schedulers, exception dates), recipes, users and passwords, e-mail and RSS
feeds, rotating menus.
Includes support for a wide range of communication drivers.
Multiple drivers communication capability.
Remote monitoring and control. Client-Server functionality.
Simulation with PB610 Panel Builder 600.
Powerful scripting language for automating HMI applications. Script debugging improves efficiency in
application development.
Rich gallery of vector symbols and objects.
Project & page templates.
Optional plug-in modules for fieldbus systems, networks and controllers.

Operating Instructions 6 CP600/Issue: 12.2011
Standards and Approvals
The Control Panels have been designed for installation and use in an industrial environment in com-
pliance with the 2004/108/EC EMC Directive and with the following harmonized standards:
EN 61000-6-4
EN 61000-6-2
In compliance with the above regulations the products are CE marked.
The installation of these devices into the residential, commercial and light-industrial environments is al-
lowed only in the case that special measures are taken in order to get the conformity to EN 61000-6-3.
Product Identification
The Control Panel products are identified by a product label. The label reports several information, includ-
ing the model name, the part number, the power supply, the date of production (in the following format:
ywwy) and two barcodes. The first code is the version code, the second one the serial number (S.N.).
Example of product label
Information on type plate (example)
Description
CP650
Product type
1SAP550100R0001
Product part number
1231
ywwy – week and year of production
09994971505
Serial number
020308A05002140
Version number of the product
WEB 1.5.15.117
Version number of the MicroBrowser (only valid for CP6xx-WEB)

Operating Instructions 7 CP600/Issue: 12.2011
Technical Specifications
Parameter
Value
Back-up battery
3V 50mAh Lithium, rechargeable, not user-replaceable, PANASONIC model VL2330
Fuse
Automatic
Environmental Conditions
Parameter
Value
According to
Operating temperature (vertical installation)
0 °C … +50 °C
EN 60068-2-14
Storage temperature
-20 °C … +70 °C
EN 60068-2-14
Operating and storage humidity
5 % … 85 % RH not-condensing
EN 60068-2-30
Vibrations
5 Hz … 9 Hz, 7 mm
p-p
9 Hz … 150 Hz, 1 g
EN 60068-2-6
Shock
± 50 g, 11 ms, 3 pulses per axis
EN 60068-2-27
Protection class
IP66 front panel *
EN 60529
Touchscreen technology
Resistive
-
Touchscreen reliability
> 1 million operations
-
*) The front face of the Control Panel unit, installed in a solid panel, has been tested using conditions
equivalent to the standards shown in the table above. Even though the Control Panel unit’s level of resis-
tance is equivalent to these standards, oils that should have no effect on the Control Panel can possibly
harm the unit. This can occur in areas where either vaporized oils are present, or where low viscosity cut-
ting oil are allowed to adhere to the unit for long periods of time. If the Control Panel’s front face protec-
tion sheet becomes peeled off, these conditions can lead to the ingress of oil into the Control Panel and
separate protection measures are suggested.
Also, if non-approved oils are present, it may cause deformation or corrosion of the front face. Therefore,
prior to installing the Control Panel be sure to confirm the type of conditions that will be present in the
Control Panel’s operating environment.
If the installation gasket is used for a long period of time, or if the unit and its gasket are removed from the
panel, the original level of the protection cannot be guaranteed. To maintain the original protection level,
be sure to replace the installation gasket regularly.

Operating Instructions 8 CP600/Issue: 12.2011
Electromagnetic Compatibility (EMC)
Test executed on the 230 V AC side of the Power Supply (EN 61000-4-11).
Parameter
Value
According to
Emitted interference
Class A
EN 55011
Electrostatic
8 kV (air electrostatic discharge)
4 kV (contact electrostatic discharge)
EN 61000-4-2
Immunity to radiated radio-
frequency
80 MHz … 1 GHz, 10 V/m
1 GHz … 2 GHz, 3 V/m
2 GHz … 2.7 GHz, 1 V/m
EN 61000-4-3
Electromagnetic field
900 MHz, 10 V/m
EN V 50204
Immunity to conducted dis-
turbances inducted by radio-
frequency field
0.15 MHz … 80 MHz 10 V
EN 61000-4-3
Fast transient
2 KV power supply
1 KV signal lines
EN 61000-4-4
Input and output AC power
ports
Level: 2 kV (L1/L2-PE) 1 kV (L1-L2)
EN 61000-4-5
Signal port
Level: 1 kV (line to earth)
Immunity to conducted dis-
turbances inducted by radio-
frequency field
0.15 … 80 MHz, 10 V
EN 61000-4-6
Voltage dips, short interrup-
tions and voltage variations
immunity test
Port: AC mains.
Level: 0 % / duration: 1 cycle and 250 cycles (50 Hz) or
300 cycles (60 Hz);
40 % / duration: 10 cycles (50 Hz) or 12 cycles (60 Hz);
70 % / duration: 25 cycles (50 Hz) or 30 cycles (60 Hz);
Phase: 0°-180°
Electrostatic discharge
8 kV in air
EN 61000-4-2
PC/Printer Port
RS-232, RS-485, RS-422 software configurable
300 … 38400 baud
PLC Port RS-232, RS-485, RS-422 software configurable
300 … 38400 baud
AUX Port
Connector DB-9 pin female (functionality can be confi-
gured with an optional communication module)
User memory
Flash 128 Mb
Recipe memory
32 kB FRAM
Hardware clock
Clock/calendar with back-up battery
Accuracy RTC (at 25°C
operating)
< 100 ppm

Operating Instructions 9 CP600/Issue: 12.2011
Durability Information
Parameter
Value
Backlight service life (LED type)
MTBF value: 40,000 hrs
(time of continuos operation until the brightness of the backlight
reaches 50 % when the sorrounding temperature reach 25 °C), see
1
Backlight service life (CCFL type)
MTBF value: 50,000 hrs or more
(time of continuos operation until the brightness of the backlight
reaches 50 % when the sorrounding temperature is 25 °C), see
1
Battery lifetime
10 years if the surrounding temperature is 25 °C
5 years if the surrounding temperature is 40 °C
1 year if the surrounding temperature is 50 °C, see
1
Front foil silk screen
(without directly expose to sunlight
or UV ray)
10 years if the surrounding temperature is 25 °C
UV Resistance
Indoor applications: After 300 hrs cycled humidity in QUV, some
yellowing and brittleness may be present.
Touch panel
(resistive film, analog)
1,000,000 or more of activations, see 2
1Extended use in environments where the surrounding air temperature is 40 °C or higher may degrade
backlight quality/reliability/durability.
2Solvent resistance:
Contact for ½ hour at 21 °C, no visible effect: Acetone, Butyl Cellosolve, Cyclohexanone, Ethyl Acetate,
Hexane, Isopropyl Alcohol, MEK, Methylene Chloride, Toluene, Xylene
Contact for 24 hours at 49 °C, no visible effect: Clorox, Coffee, Downy, Fantastik, Formula 409, Ketchup,
Lemon Juice, Mr. Clean, Mustard (slight yellow stain), Spray ‘N Wash, Tea, Tomato Juice, Top Job, Wisk

Operating Instructions 10 CP600/Issue: 12.2011
Technical Data
Model
CP650(-WEB)-x
CP660(-WEB)-x
CP675(-WEB)-x
Display/Backlight
TFT Color / LED
TFT Color / CCFL
TFT Color / CCFL
Colors
64 K
64 K
64 K
Resolution
800 x 600
800 x 600
1024 x 768
Diagonal (inches)
10.4”
12.1“
15“
Dimming
Yes
Yes
Yes
Touchscreen
Yes
Yes
Yes
User memory flash
128 MB
128 MB
128 MB
Flash card option
-
-
-
Recipe memory
Yes. Flash memory
storage limited only by
available memory
Yes. Flash memory
storage limited only by
available memory
Yes. Flash memory
storage limited only by
available memory
PLC Port RS-232, RS-485,
RS-422
RS-232, RS-485,
RS-422
RS-232, RS-485,
RS-422
Programming/printer port RS-232, RS-485,
RS-422
RS-232, RS-485,
RS-422
RS-232, RS-485,
RS-422
Aux port (optional field-
bus/Ethernet)
Yes Yes Yes
Ethernet programming
Yes
Yes
Yes
Ethernet port
10/100 Mbit/s
10/100 Mbit/s
10/100 Mbit/s
USB port Host interface, version
2.0
Host interface, version
2.0
Host interface, version
2.0
Graphic
Yes
Yes
Yes
Video input option
-
-
-
Trend acquisition and display
Yes
Yes
Yes
Battery
Rechargeable
Rechargeable
Rechargeable
Real-time clock
Yes
Yes
Yes
Password
Yes
Yes
Yes
Alarms
1024
1024
1024
Event list
Yes, configurable
Yes, configurable
Yes, configurable
Voltage
18-30 V DC
18-30 V DC
18-30 V DC
Current rating (at 24 V DC)
0.75 A
1.05 A
1.05 A
Weight
2 kg
2.8 kg
3.4 kg

Operating Instructions 11 CP600/Issue: 12.2011
Dimensions
Model
A
B
C
H
L
mm
inches
mm
inches
mm
inches
mm
inches
mm
inches
CP650(-WEB)-x
276
10.86”
221
8.70”
42
1.65”
232
9.13”
287
11.30”
CP660(-WEB)-x
326
9.30”
256
10.1”
42
1.65”
267
10.51”
337
13.26”
CP675(-WEB)-x
381
15”
296
11.65”
46
1.82”
307
12.1”
392
15.43”
Model
CSD: Minimum compass safe distance
of standard compass
CSD2: Minimum compass safe distance
of steering compass, standby steering
compass and emergency compass
mm
inches
mm
inches
CP650(-WEB)-x
400
15.74”
250
9.84”
CP660(-WEB)-x
500
19.68”
300
11.81”
CP675(-WEB)-x
650
25.60”
400
15.74”

Operating Instructions 12 CP600/Issue: 12.2011
Installation Environment
The equipment is not intended for continuous exposure to direct sunlight. This might accelerate the aging
process of the front panel film.
The equipment is not intended for installation in contact with corrosive chemical compounds. Check the
resistance of the front panel film to a specific compound before installation.
Do not use tools of any kind (screwdrivers etc.) to operate the keyboard of the panel or the touchscreen.
In order to meet the front panel protection classifications, proper installation procedure must be followed:
The borders of the cutout must be flat.
The cutout for the panel must be of the dimensions indicated in this manual.
Screw up each fixing screw until the plastic bezel corner get in contact with the panel.
The IP66 is guaranteed only if:
Maximum deviation from the plane surface to the cut-out: Ø 0.5 mm
Thickness of the plate the equiment is mounted: 1.5 mm to 6 mm
Maximum surface roughness where the gasket is applied: Ø 120 µm
Applying the Rectangular Gasket
Apply the gasket on the rear of the frame.
A
Gasket
B
Installation cut-out

Operating Instructions 13 CP600/Issue: 12.2011
Installation Procedure
Place the fixing brackets.
CAUTION!
Screw each fixing screw until the bezel corner gets in contact with the panel.

Operating Instructions 14 CP600/Issue: 12.2011
Connections
Connections of the Control Panel
1
Power
3
PLC port
5
Ethernet port
2
Aux port
4
PC/printer port
6
USB port for
PLC Port
The PLC port is used to communicate with the PLC or with another type of controller.
Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422,
RS-485. The used cable selects the appropriate signals.
NOTE
It is always necessary to use the correct cable type to connect on the PLC.
If the proper cable is not used, communication with the PLC will not be possible.
The connector is a DB-9 pin female.
Pin
Description
Pin
Description
Pin
Description
1
GND
4
RX/CHB-
7
CTS/CHB+
2
5
8
RTS/CHA+
3
TX/CHA-
6
+5 V output
9

Operating Instructions 15 CP600/Issue: 12.2011
Communication Cable
The communication cable must be chosen for the type of device being connected.
Connection to an AC-500 with the TK681 CP600-AC500 RS232 communication cable
Connection to an AC-500(-eCo) with the TK682 CP600-AC500-eCo RS485 communication cable
1
Shield
2
SubD9 male

Operating Instructions 16 CP600/Issue: 12.2011
PC/Printer Port
The PC/printer port can be used to communicate with the PLC or with another type of controller.
Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422,
RS-485. The used cable selects the appropriate signals.
NOTE
It is always necessary to use the correct cable type to connect on the PLC.
If the proper cable is not used, communication with the PLC will not be possible.
The connector is a DB-9 pin female.
Pin
Description
Pin
Description
Pin
Description
1
GND
4
RX/CHB-
7
CTS/CHB+
2
5
8
RTS/CHA+
3
TX/CHA-
6
+5 V output
9
The communication cable must be chosen for the type of device being connected.
Ethernet Port
Ethernet Port
A
OFF: No activity
BLINKING: Activity
B
ON: Valid link hast NOT been detected
OFF: Valid link has been detected
Pin
Description
Pin
Description
Pin
Description
Pin
Description
1
TX OUT +
3
RX OUT +
5
7
2
TX OUT -
4
6
RX OUT -

Operating Instructions 17 CP600/Issue: 12.2011
Power Supply, Grounding and Shielding
DC Power Connector, Female - R/C Terminal Blocks (XCFR2), manufactured by Weidmüller Inc.,
Cat. No. BLZ 5.08, torque 4.5 lb-in
NOTE
Ensure that the power supply has enough power capacity for the operation of the equipment.
The unit must always be grounded to earth. Grounding helps limit the effects of noise due to electromag-
netic interference on the control system.
1. Do the earth connection using either the screw or the faston terminal located near the power supply
terminal block. A label helps identify the ground connection.
2. Connect to ground the terminal 3 on the power supply terminal block.
3. The power supply circuit may be floating or grounded. In the latter case, connect to ground the power
source common as shown in the figure below with a dashed line.
When using the floating power scheme, note that the panes internally connects the power common to
ground with a 1 MΩ resistor in parallel with a 4,7 nF capacitor.
The power supply must have double or reinforced insulation.
Suggested wiring for the power supply.
All the electronic devices in the control system must be properly grounded. Grounding must be performed
according to applicable regulations.

Operating Instructions 18 CP600/Issue: 12.2011
AUX Port
The AUX port is a communication port specially designed for industrial network communication. The AUX
port connector is a 9 pin D sub type. The functionality of the AUX port depends on the optional Communi-
cation Module which is plugged into the unit.
NOTE
The pin assignment of the AUX port connector is described in the manual of the Communi-
cation Module.
WARNING!
Do not plug the Communication Module and the ETAD adapter when power is applied to the
operator panel.
1. Open the housing.
2. Insert the Communication Module pressing simultaneously on the four corners.

Operating Instructions 19 CP600/Issue: 12.2011
Battery
The Control Panels are equipped with a rechargeable lithium battery, not user-replaceable.
The battery maintains the hardware real-time clock (date and time).
Charging the Battery
At first installation recharge the battery for 48 hours.
When the battery is charged, it assures a period of 3 month of data back-up at 25 °C.
Recycling and Disposal
The battery must not be disposed as unsorted domestic waste.
Dispose the battery according to the local regulations.