ABB FAIO-01 User manual

—
OPTIONS FOR ABB DRIVES, CONVERTERS AND INVERTERS
FAIO-01 analog I/O extension module
User's manual

FAIO-01 analog I/O
extension module
User's manual
Table of contents
1. Safety instructions
4. Installation
5. Start-up
3AUA0000124968 Rev C
EN
EFFECTIVE: 2019-12-05
© 2019 ABB Oy. All Rights Reserved.

Table of contents
1 Safety instructions
7Contents of this chapter ............................................................
7Use of warnings ........................................................................
8Safety in installation ..................................................................
2 Introduction to the manual
9Contents of this chapter ............................................................
9Target audience ........................................................................
9Compatibility .............................................................................
10Terms and abbreviations ...........................................................
3 Hardware description
11Contents of this chapter ............................................................
11Product overview ......................................................................
12Layout .................................................................................
4 Installation
15Contents of this chapter ............................................................
15Unpacking and examining the delivery .....................................
15Installing the module .................................................................
16…onto the drive control unit ...............................................
17…onto an extension adapter module .................................
17Selecting the input mode, voltage range and signal type .........
18General cabling instructions .....................................................
18Wiring ........................................................................................
18
Connection example for motor winding temperature
measurement ......................................................................
19Connection example for external devices ..........................
5 Start-up
21Contents of this chapter ............................................................
21Before you start .........................................................................
22Setting the parameters ..............................................................
22Example – Primary control program ...................................
Table of contents 5

6 Diagnostics
23Contents of this chapter ............................................................
23Faults and warning messages ..................................................
23LEDs .........................................................................................
7 Technical data
25Contents of this chapter ............................................................
25Data ..........................................................................................
25Degree of protection ...........................................................
25Ambient conditions .............................................................
25Package ..............................................................................
26Hardware settings ...............................................................
26A/D conversion resolution ..................................................
26Isolation areas ....................................................................
27Analog inputs and outputs ..................................................
27Power supply ......................................................................
27General ...............................................................................
28Dimensions ...............................................................................
Further information
6 Table of contents
27

1
Safety instructions
Contents of this chapter
The chapter contains the warning symbols used in this manual and
the safety instructions which you must obey when you install or
connect an optional module to a drive, converter or inverter. If you
ignore the safety instructions, injury, death or damage can occur.
Read this chapter before you start the installation.
Use of warnings
Warnings tell you about conditions which can cause injury or death,
or damage to the equipment. They also tell you how to prevent the
danger. Notes draw attention to a particular condition or fact, or give
information on a subject.
The manual uses these warning symbols:
Safety instructions 7

WARNING!
Electricity warning tells about hazards from electricity which
can cause injury or death, or damage to the equipment.
WARNING!
General warning tells about conditions, other than those
caused by electricity, which can cause injury or death, or
damage to the equipment.
Safety in installation
These instructions are for all who install or connect an optional module
to a drive, converter or inverter and need to open its front cover or
door to do the work.
WARNING!
Obey these instructions. If you ignore them, injury or death,
or damage to the equipment can occur. If you are not a
qualified electrical professional, do not do electrical installation
or maintenance work. Go through these steps before you begin
any installation or maintenance work.
•Disconnect the drive, converter or inverter from all possible power
sources. After you have disconnected the drive, converter or
inverter, always wait for 5 minutes to let the intermediate circuit
capacitors discharge before you continue.
• Disconnect all dangerous voltages connected to other control
signal connectors in reach. For example, it is possible that
230 V AC is connected from outside to a relay output or digital
input of the drive, converter or inverter.
• Always use a multimeter to make sure that there are no parts
under voltage in reach. The impedance of the multimeter must
be at least 1 Mohm.
8 Safety instructions
28

2
Introduction to the manual
Contents of this chapter
This chapter introduces this manual.
Target audience
This manual is intended for people who plan the installation, install,
commission, use and service the extension module. Before you do
work on the module, read this manual and the applicable drive,
converter or inverter manual that contains the hardware and safety
instructions for the product in question.
You are expected to know the fundamentals of electricity, wiring,
electrical components and electrical schematic symbols.
The manual is written for readers worldwide. Both SI and imperial
units are shown.
Compatibility
See the appropriate hardware manual.
Introduction to the manual 9

Terms and abbreviations
DescriptionTerm
Frequency converter for controlling AC motorsDrive
Electromagnetic compatibilityEMC
Optional analog I/O extension moduleFAIO-01
10 Introduction to the manual