manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. ACME
  6. •
  7. Dj Equipment
  8. •
  9. ACME LED-920D User manual

ACME LED-920D User manual

SUPER NOVA
User Manual
Professional Entertainment Technology
1-
TABLE OF CONTENTS
1. Safety Instruction
2. Technical Specification
3. Installation
4. How to Control the Unit
4.1 Master/Slave operation
4.2 Easy controller CA-8
4.3 Universal DMX controller
5. DMX 512 Configuration
6. DMX 512 Connection
7. Fixture Cleaning
2-
1. Safety Instruction
WARNING
♦Please keep this User Manual for future consultation. If you sell the unit to another user,
be sure that they also receive this instruction booklet.
♦Unpack and check carefully there is no transportation damage before using the unit.
♦Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
♦It’s important to ground the yellow/green conductor to earth in order to avoid electric
shock.
♦The unit is for indoor use only and use only in a dry location.
♦The unit must be installed in a location with adequate ventilation, at least 50cm from
adjacent surfaces. Be sure that no ventilation slots are blocked.
♦Disconnect mains power before fuse replacement or servicing.
♦Replace fuse only with the same type.
♦Make sure there are not flammable materials close to the unit while operating as it is fire
hazard.
♦Use safety cable when fixes this unit.
♦Maximum ambient temperature is TA: 40℃and don’t operate it where the temperature is
higher than this.
♦Unit surface temperature may reach up to 60℃. Don’t touch the housing bare-hand during
its operation. Turn the power off and wait for 15 minutes for cool down before replacing
bulb or serving.
♦In the event of serious operating problem, stop using the unit immediately. Never try to
repair the unit by yourself. Repair carried out by unskilled people can lead to damage or
malfunction. Please contact the nearest authorized technical assistance center and
always use the same type spare parts.
♦Don’t connect the device to any dimmer pack or power pack.
♦Do not touch any wire during operation as high voltage might be causing electric shock.
Please read the instruction carefully which including important
information about the installation, operation and maintenance.
3-
2. Technical Specification
•Voltage: AC 100V-240V 50-60Hz
•2 Channels
Channel 1 = Dimmer/Strobe
Channel 2 = Rotation
•It can be operated by DMX512 control or can be used as an individual unit without
controller.
•It can be linked together as many as required in master/slave mode, and perform the great
built-in programmed lighting shows triggered by music.
•Please use a 3 pin XLR cable/plug when connecting them together.
•Fan cooled.
•Dimension: 194 x 202 x 141 mm
•Weight: 1kg
3. Installation
You can install the unit on the truss or ceiling, Use clamps to fix the unit to truss. Always
ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always
ensure that the structure to which you are attaching the unit is secure and is able to support
a weight of 10 kg for each unit.
4-
4. How To Control The Unit
Three ways to operation:
A. Master/Slave operation
B. Easy controller CA-8
C. Universal DMX controller
6.1 Master/Slave operation
The unit can be linked together in daisy chain as many as you need in master/slave mode to
perform the great built-in pre-programmed lighting shows triggered by music.
In Master/Slave mode refer to the DMX settings below:
Master unit: DMX start address MUST be set to 001. ( first DIP switch = ON, all other
are OFF)
Slave units: DMX start address may have any value but NOT 001 ( example: set the
first 3 DIP switches to ON)
﹡2-light show
Dipswitch 10 ”off” means the unit works normally and “on” means inversion. In order to
create a great light show, you can set dip switch 10 ”on” on any unit that is linking to the
master unit to get contrast movement to the master unit, even if you have two units only.
Dipswitch 10 on the first ( Master ) unit is no use for the 2-light show as it is the master unit
that operates the light show.
6.2 Easy Controller (by CA-8)
The easy remote control is used only in master/slave mode. By
connecting to the 1/4” microphone jack of the first unit (its DMX input
plug is not used), you will find that the remote control all the first unit
will control all the other units for Stand by, Function and Mode.
Built-in lighting shows triggered by Easy Controller:
Stand by Blackout the unit
Function 1. Synchronous Strobe
2. Two light Strobe Turn left and right
Mode Sound/Strobe (LED OFF) Rotation (LED ON)
5-
6.3 Universal DMX controller
When using a universal DMX controller to control the chain of units, you have to set DMX
address by Dip switches from 1 to 9 to make sure all the units will receive its DMX signal.
Please refer to the following diagram to know how to address your DMX 512 system in the
binary code.
DMX 512 Address Chart:
Dip-switches # 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # 9 #10
Value 1 2 4 8 16 32 64 128 256 2-light show
•Examples:
Channel 1:dip / on: #1 (=1)
Channel 3:dip / on: #1, #2 (1+2=3)
Channel 5:dip / on: #1, #3 (1+4=5)
Channel 7:dip / on: #1, #2, #3 (1+2+4=7)
5. DMX 512 Configuration
6-
6. DMX 512 Connection
The DMX 512 is widely used in intelligent lightings and with a maximum of 512 channels.
1.If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin
adapter-cable.
2.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120
ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug
and plug it in the DMX-output of the last unit.
3.Connect the unit together in a ‘daisy chain’ by XLR plug from the output of the unit
to the input of the next unit. The cable can not be branched or split to a ‘Y’ cable.
DMX 512 is a very high-speed signal. Inadequate or damaged cables, solder
joints or corroded connectors can easily distort the signal and shut down the
system.
4.The DMX output and input connectors are pass-through to maintain the DMX
circuit, when power is connected to the unit.
5.Each lighting unit needs to have an address set to receive the data sent by the
controller. The address number is between 0-511 (usually 0 & 1 are equal to 1).
6.The end of the DMX 512 system should be terminated to reduce signal errors.
7.3 pin XLR connectors are more popular than 5 pin XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
7-
7. Fixture Cleaning
The cleaning of internal and external optical lenses and/or mirrors must be carried out
periodically to optimize light output. Cleaning frequency depends on the environment in
which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater
accumulation of dirt on the unit’s optics.
yClean with soft cloth using normal glass cleaning fluid.
yAlways dry the parts carefully.
yClean the external optics at least every 20 days. Clean the internal optics at least every
30/60 days.
Innovation, Quality, Performance
EC - Declaration of Conformity
We declare that our products (lighting equipments) comply with the
following specification and bears CE mark in accordance with the provision
of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC.
EN55014-2: 1997 A1:2001, EN61000-4-2: 1995; EN61000-4-3:2002;
EN61000-4-4: 1995; EN61000-4-5: 1995, EN61000-4-6:1996,
EN61000-4-11: 1994.
&
Harmonized Standard
EN60598-1: 2000+ALL:2000+A12:2002
Safety of household and similar electrical appliances
Part 1 : General requirements

This manual suits for next models

2

Other ACME Dj Equipment manuals

ACME CYC-200 FC User manual

ACME

ACME CYC-200 FC User manual

ACME LED-MTX25 IP User manual

ACME

ACME LED-MTX25 IP User manual

ACME LED-256D RGB User manual

ACME

ACME LED-256D RGB User manual

ACME Stage Blinder P4 User manual

ACME

ACME Stage Blinder P4 User manual

ACME XP-1000WZ User manual

ACME

ACME XP-1000WZ User manual

ACME MACE User manual

ACME

ACME MACE User manual

ACME Theatre LED Colour Flood User manual

ACME

ACME Theatre LED Colour Flood User manual

ACME MH-575S User manual

ACME

ACME MH-575S User manual

ACME LED WAVE 100 User manual

ACME

ACME LED WAVE 100 User manual

ACME FARANDOLE AM-BAR User manual

ACME

ACME FARANDOLE AM-BAR User manual

ACME CA-DD12 II User manual

ACME

ACME CA-DD12 II User manual

ACME E-200 MB MC User manual

ACME

ACME E-200 MB MC User manual

ACME MH-600A Mobile Color User manual

ACME

ACME MH-600A Mobile Color User manual

ACME Color Par 36 User manual

ACME

ACME Color Par 36 User manual

ACME SAM-50 User manual

ACME

ACME SAM-50 User manual

ACME LED-635S User manual

ACME

ACME LED-635S User manual

ACME LP-F2000 VW User manual

ACME

ACME LP-F2000 VW User manual

ACME 04XOZONE User manual

ACME

ACME 04XOZONE User manual

ACME LED-BL4B User manual

ACME

ACME LED-BL4B User manual

ACME ARAS User manual

ACME

ACME ARAS User manual

ACME LED-MS50A User manual

ACME

ACME LED-MS50A User manual

ACME CEILING 40 User manual

ACME

ACME CEILING 40 User manual

ACME XP-470 BSW User manual

ACME

ACME XP-470 BSW User manual

ACME VENOM LED-460 User manual

ACME

ACME VENOM LED-460 User manual

Popular Dj Equipment manuals by other brands

Show Technology apollo user manual

Show Technology

Show Technology apollo user manual

EuroLite LED TMH-51 user manual

EuroLite

EuroLite LED TMH-51 user manual

Perel EFL15BM user manual

Perel

Perel EFL15BM user manual

SYNQ DMC.2000 Operation manual

SYNQ

SYNQ DMC.2000 Operation manual

Gemini CTRL-SIX Operation manual

Gemini

Gemini CTRL-SIX Operation manual

Chauvet Professional Ovation E-910FC IP Quick reference guide

Chauvet Professional

Chauvet Professional Ovation E-910FC IP Quick reference guide

Showlite SD101 user manual

Showlite

Showlite SD101 user manual

Velleman HQ Power VDL45ST manual

Velleman

Velleman HQ Power VDL45ST manual

Qtx SW-2 user manual

Qtx

Qtx SW-2 user manual

AVE HEX-FLAT6 user manual

AVE

AVE HEX-FLAT6 user manual

Chauvet ColorAdo 1-Quad IP Quick reference guide

Chauvet

Chauvet ColorAdo 1-Quad IP Quick reference guide

Kino Flo Celeb 850 quick start guide

Kino Flo

Kino Flo Celeb 850 quick start guide

Velleman HQ Power VDL25BM quick start guide

Velleman

Velleman HQ Power VDL25BM quick start guide

American DJ Dynasty Scan DMX User instructions

American DJ

American DJ Dynasty Scan DMX User instructions

Velleman HQ POWER VDP250ML manual

Velleman

Velleman HQ POWER VDP250ML manual

EuroLite LED B-40 user manual

EuroLite

EuroLite LED B-40 user manual

ADJ M-101HD user manual

ADJ

ADJ M-101HD user manual

Rolls 725Ex manual

Rolls

Rolls 725Ex manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.