ADF Web HD67752-A1 User manual

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 1 of 28
User Manual
Revision 1.
English
IEC 61850 Server / PROFINET Slave - Converter
(Order Code: HD67752-A1)
For Website information:
www.adfweb.com?Product=HD67752
For Price information:
www.adfweb.com?Price=HD67752-A1
Benefits and ain Features:
Very easy to configure
Triple Electrical isolation
Temperature range: -4 °C/+85°C (-4 °F/+185°F)
For other IEC 6185 Server products see also the following link:
Converter IEC 61850 Server to
www.adfweb.com?Product=HD67733 ( odbus aster)
www.adfweb.com?Product=HD67734 ( odbus Slave)
www.adfweb.com?Product=HD67735 ( odbus TCP aster)
www.adfweb.com?Product=HD67736 ( odbus TCP Slave)
www.adfweb.com?Product=HD67737 (BACnet aster)
www.adfweb.com?Product=HD67738 (BACnet Slave)
www.adfweb.com?Product=HD67739 (CAN)
www.adfweb.com?Product=HD6774 (CANopen)
www.adfweb.com?Product=HD67741 (DeviceNet aster)
www.adfweb.com?Product=HD67742 (DeviceNet Slave)
www.adfweb.com?Product=HD67743 (EtherNet/IP aster)
www.adfweb.com?Product=HD67744 (EtherNet/IP Slave)
www.adfweb.com?Product=HD67745 (J1939)
www.adfweb.com?Product=HD67746 (KNX)
www.adfweb.com?Product=HD67747 ( QTT)
www.adfweb.com?Product=HD67748 (N EA 0183)
www.adfweb.com?Product=HD67749 (N EA 2000)
www.adfweb.com?Product=HD6775 (PROFIBUS aster)
www.adfweb.com?Product=HD67751 (PROFIBUS Slave)
www.adfweb.com?Product=HD67753 (SN P anager)
www.adfweb.com?Product=HD67754 (SN P Agent)
www.adfweb.com?Product=HD67755 (Serial)
www.adfweb.com?Product=HD67756 (Ethernet)
www.adfweb.com?Product=HD67B82 (PROFINET aster)
www.adfweb.com?Product=HD67C65 (EnOcean)
Do you have your customer protocol? Then go to:
www.adfweb.com?Product=HD67 3
Do you need to choose a device? Do you want help?
www.adfweb.com?Cmd=helpme
User Manual

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 2 of 28
INDEX:
Page
INDEX 2
UPDATED DOCUMENTATION 2
REVISION LIST 2
WARNING 2
TRADEMARKS 2
SECURITY ALERT 3
EXAMPLE OF CONNECTION 4
CONNECTION SCHEME 5
CHARACTERISTICS 6
CONFIGURATION 6
POWER SUPPLY 7
FUNCTION MODES 8
LEDS 9
ETHERNET 1
USE OF COMPOSITOR SW67752 11
NEW CONFIGURATION / OPEN CONFIGURATION 12
SOFTWARE OPTIONS 13
SET COMMUNICATION 15
IEC 6185 ACCESS 17
TLS KNOWN CERTIFICATE 18
PROFINET XML 19
UPDATE DEVICE 2
PLC CONFIGURATION 22
MECHANICAL DIMENSIONS 25
ORDERING INFORMATIONS 26
ACCESSORIES 26
DISCLAIMER 27
OTHER REGULATIONS AND STANDARDS 27
WARRANTIES AND TECHNICAL SUPPORT 28
RETURN POLICY 28
UPDATED DOCU ENTATION:
Dear customer, we thank you for your attention and we remind you that
you need to check that the following document is:
Updated
Related to the product you own
To obtain the most recently updated document, note the “document code”
that appears at the top right-hand corner of each page of this document.
With this “Document Code” go to web page www.adfweb.com/download/
and search for the corresponding code on the page. Click on the proper
“Document Code” and download the updates.
REVISION LIST:
WARNING:
ADFweb.com reserves the right to change information in this manual about
our product without warning.
ADFweb.com is not responsible for any error this manual may contain.
TRADE ARKS:
All trademarks mentioned in this document belong to their respective
owners.
Revision Date Author Chapter Description
1. 18/ 9/2 19 Ff All First Release

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 3 of 28
SECURITY ALERT:
G ENERAL I NFOR ATION
To ensure safe operation, the device must be operated according to the instructions in the manual. When using the device, legal and
safety regulation are required for each individual application. The same applies also when using accessories.
I NTENDED U SE
Machines and systems must be designed so the faulty conditions do not lead to a dangerous situation for the operator (i.e.
independent limit switches, mechanical interlocks, etc.).
Q UALIFIED P ERSONNEL
The device can be used only by qualified personnel, strictly in accordance with the specifications.
Qualified personnel are persons who are familiar with the installation, assembly, commissioning and operation of this equipment and
who have appropriate qualifications for their job.
R ESIDUAL R ISKS
The device is state-of-the-art and is safe. The instruments can represent a potential hazard if they are inappropriately installed and
operated by untrained personnel. These instructions refer to residual risks with the following symbol:
This symbol indicates that non-observance of the safety instructions is a danger for people that could lead to serious injury or
death and / or the possibility of damage.
CE CONFOR ITY
The declaration is made by our company. You can send an email to [email protected]om or give us a call if you need it.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 4 of 28
EXA PLES OF CONNECTION:

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 5 of 28
CONNECTION SCHE E:
Figure 1: Connection scheme for HD67752-A1

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 6 of 28
CHARACTERISTICS:
The HD67752-A1 is IEC 6185 Server / PROFINET Slave - Converter.
It allows for the following characteristics:
Isolation between Ethernet - Power Supply;
Two-directional information between IEC 6185 bus and PROFINET bus;
Mountable on 35mm Rail DIN;
Wide power supply input range: 8…24V AC or 12…35V DC;
Wide temperature range: -4 °C / 85°C [-4 °F / +185°F].
CONFIGURATION:
You need Compositor SW67752 software on your PC in order to perform the following:
Define the parameters of IEC 6185 line;
Define the parameters of PROFINET line;
Define IEC 6185 variables that contains the data to read from PROFINET side;
Define IEC 6185 variables that contains the data to write from PROFINET side;
Update the device.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 7 of 28
POWER SUPPLY:
The devices can be powered at 8…24V AC and 12…35V DC. For more details see the two tables below.
VAC
VDC
Vmin Vmax Vmin Vmax
8V 24V 12V 35V
Consumption at 24V DC:
Device Consumption [W/VA]
HD67752-A1 3.5
HD67752-A1
Caution:
Do n
ot reverse the polarity power

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 8 of 28
FUNCTION ODES:
The device has got two function modes depending on the position of the ‘Dip1 of Dip-Switch A’:
The first, with ‘Dip1 of Dip-Switch A’ at “OFF” position, is used for the normal working of the device.
The second, with ‘Dip1 of Dip-Switch A’ at “ON” position, is used for uploading the Project and/or Firmware.
For the operations to follow for the updating, see ‘UPDATE DEVICE’ section.
According to the functioning mode, the LEDs will have specific functions, see ‘LEDS’ section.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 9 of 28
LEDS:
The device has got six LEDs that are used to give information about the functioning status.
The various meanings of the LEDs are described in the table below.
LED Normal ode Boot ode
1: ON [supply voltage ]
(green)
ON: Device powered
OFF: Device not powered
ON: Device powered
OFF: Device not powered
2: MT [maintenance display]
(yellow)
ON: Maintenance Problem is present
OFF: No maintenance are present
Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
3: BF [bus fault] (red)
ON: The Ethernet connection is defective; the IP
address exists several times in the network; the own
NameOfStation exists several times in the network; no
IP address has been set
Flashing: At least one configured AR is no longer in
the data exchange
OFF: No errors are present
Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
4: SF [group error] (red) ON: At least one AR is not in the data exchange
OFF: No errors are present
Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
5: Ethernet1 Tx (green) Blinks when is transmitting Ethernet frames Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress
6: Ethernet2 Tx (green) Blinks when is transmitting Ethernet frames Blinks quickly: Boot state
Blinks very slowly (~0.5Hz): update in progress

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 1 of 28
ETHERNET:
IEC 6185 connection, PROFINET connection and the updating of the converters must be made using Connector3 and/or Connector4 of the
HD67752-A1 with at least a Category 5E cable. The maximum length of the cable should not exceed 1 m. The cable has to conform to the
T568 norms relative to connections in cat.5 up to 1 Mbps. To connect the device to an Hub/Switch is recommended the use of a straight
cable, to connect the device to a PC/PLC/other is recommended the use of a cross cable.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 11 of 28
USE OF CO POSITOR SW67752:
To configure the Converter, use the available software that runs with Windows called SW67752. It is downloadable on the site
www.adfweb.com and its operation is described in this document. This manual is referenced to the last version of the software present on
our web site). The software works with MSWindows (XP, Vista, Seven, 8, 1 ; 32/64bit).
When launching the SW67752, the window below appears (Fig. 2).
Note:
It is necessary to have installed .Net Framework 4.
Figure 2: Main window for SW677
5
2

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 12 of 28
NEW CONFIGURATION / OPEN CONFIGURATION:
The “New Configuration” button creates the folder which contains the entire device’s configuration.
A device’s configuration can also be imported or exported:
To clone the configurations of a programmable “IEC 6185 Server / PROFINET Slave -
Converter” in order to configure another device in the same manner, it is necessary to
maintain the folder and all its contents;
To clone a project in order to obtain a different version of the project, it is sufficient to
duplicate the project folder with another name and open the new folder with the
button “Open Configuration”.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 13 of 28
SOFTWARE OPTIONS:
By pressing the “Settings” ( ) button there is the possibility to change the language of the software and check the updatings for the
compositor.
In the section “Language” it is possible to change the language of the
software.
In the section “Connection Options”, it is possible to check if there are some
updatings of the software compositor in ADFweb.com website.
Checking the option “Check Software Update at Start of Program”, the
SW67752 checks automatically if there are updatings when it is launched.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 14 of 28
In the section “Software Settings”, it is possible to enable/disable some
keyboard’s commands for an easier navigation inside the tables contained in
the different sections of the software.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 15 of 28
SET CO UNICATION:
This section defines the fundamental communication parameter of two buses, PROFINET and
IEC 6185 .
By pressing the “Set Communication” button from the main window of SW67752 (Fig. 2)
the window “Set Communication” appears (Fig. 3).
The means of the fields for “IEC6185 Server” are:
In the field “Port” the port number used for IEC 6185 communication is defined;
If the field “Password” the password used for accessing to IEC 6185 variables is
defined.
The means of the fields for “TLS Server” are:
If the field “Enable TLS” is checked, the TLS protocol for secure connection is
enabled;
In the field “Key” the key for the authentication is defined;
In the field “Key Password” the password for decrypting the key is defined;
In the field “Server Certificate” the certificate for the server is defined;
In the field “Root Certificate” the root of the server is defined;
If the field “Enable Only Known Certificates” is checked, the converter will accept
just connection from known Clients (defined in the section “TLS Known Certificate”).
Figure 3: “Set Communication”
window

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 16 of 28
The means of the fields for “PROFINET” are:
In the field “IP Address” the IP address of the converter is defined;
In the field “SubNet ask” the Subnet Mask of the converter is defined;
In the field “Gateway” the default gateway of the net is defined. This feature can be enabled or disabled pressing the Check Box
field. This feature is used for going out of the net;
In the field "Name of Station" the name of the PROFINET node is defined;
In the fields “Number Byte IN” the number of input byte of the converter is defined;
In the fields “Number Byte Out” the number of output byte of the converter is defined.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 17 of 28
Figure 4: “IEC 61850 Access” window
IEC 61850 ACCESS:
By Pressing the “IEC 61850 Access” button from the main window for SW67752 (Fig. 2) the window “Set Variables Access for IEC 6185 ”
appears (Fig. 4).
This section is used to define the IEC 6185 variables accessible from serial side.
The means of the fields are:
If the field “Enable” is checked, the IEC 6185 variable is enabled;
In the field “Name” the name of the IEC 6185 variable is defined;
In the field “Type” the data format of the IEC 6185 variable is defined;
If the field “Read Only” is checked, the IEC 6185 variable is just in reading. Otherwise, it is writeable too;
In the field “Position” the starting byte of the PROFINET arrays from/to which taking/mapping the data is defined;
In the field “Start Bit” the starting bit of the byte of the field “Position” is defined;
In the field “Conversion” the conversion of the data is defined. This option is used to convert the data format between PROFINET
and IEC 6185 ;
In the field “ olt. Factor” a multiplicative factor of the value is defined;
In the field “ nemonic” a description of the variable is defined.

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 18 of 28
TLS KNOWN CERTIFICATE:
By pressing the “TLS Known Certificate” button from the Main Window of SW67752 (Fig. 2) the “Definition the list of Known Certificates”
window appears (Fig. 5).
The data of the columns have the following meanings:
If the field “Enable” is checked, the TLS certificate is allowed;
In the field “Certificate” the certificate of the Client is defined;
In the field “ nemonic” a description is defined.
Figure 5: “TLS Known Certificate” window

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 19 of 28
PROFINET X L:
By Pressing the “PROFINET X L” button from the main window for
SW67752 (Fig. 2) it is possible to generate the xml file to be imported into
the master PROFINET.
Figure 6: “PROFINET XML File Name” window

Industrial Electronic Devices
ADFweb.com S.r.l.
User Manual
IEC 61850 Server /
PROFINET S
lave
Document code: MN67752_ENG Revision 1. Page 2 of 28
UPDATE DEVICE:
By pressing the “Update Device” button, it is possible to load the created
Configuration into the device; and also the Firmware, if necessary. This by using the
Ethernet port.
If you don’t know the actual IP address of the device you have to use this procedure:
Turn OFF the Device;
Put Dip1 of ‘Dip-Switch A’ in ON position;
Turn ON the device
Connect the Ethernet cable;
Insert the IP “192.168.2.205”;
Select which operations you want to do;
Press the “Execute update firmware” button to start the upload;
When all the operations are “OK” turn OFF the Device;
Put Dip1 of ‘Dip-Switch A’ in OFF position;
Turn ON the device.
If you know the actual IP address of the device, you have to use this procedure:
Turn ON the Device with the Ethernet cable inserted;
Insert the actual IP of the Converter;
Select which operations you want to do;
Press the “Execute update firmware” button to start the upload;
When all the operations are “OK” the device automatically goes at Normal Mode.
At this point the configuration/firmware on the device is correctly updated.
Figure 7: “Update device” windows