ADLINK Technology COM Express nanoX-TC User manual

COM.0 Rev. 2.0 Type 10
nanoX-TC
User’s Manual
Manual Revision: 2.01
Revision Date: April 1, 2013
Part Number: 50-1J037-1010

nanoX-TC User’s ManualPage2
Revision History
Release Date Change
2.00 2011/07/11 Initialrelease
2.01 2013/04/01 CorrectPCIeportusedforEG20TPCH

Page 3Express-IA533 User’s Manual Page 3Express-IA533 User’s ManualnanoX-TC User’s Manual Page3
Table of Contents
Preface ............................................................................................................................5
1Introduction ...............................................................................................................7
1.1 Description ...........................................................................................................................7
2Specifications ............................................................................................................8
2.1 Coresystem .........................................................................................................................8
2.2 Video ....................................................................................................................................8
2.3 Audio ....................................................................................................................................9
2.4 LAN .......................................................................................................................................9
2.5 MultiI/O ................................................................................................................................9
2.6 SuperI/O ..............................................................................................................................9
2.7 SDIO/MMCExtension ........................................................................................................10
2.8 Operating Systems ............................................................................................................10
2.9 Mechanical and Environmental .........................................................................................10
2.10 Power Specifications .........................................................................................................10
2.11 Power Consumption ..........................................................................................................11
2.12 Ordering Codes ..................................................................................................................11
3FunctionalDiagram .................................................................................................12
4MechanicalDimensions ..........................................................................................13
5PinoutandSignalDescriptions ..............................................................................14
5.1 COM Express™ Type 10 Pinout .......................................................................................14
5.2 PinDefinitions ....................................................................................................................15
5.3 Signal Descriptions ............................................................................................................16
6EmbeddedFunctions ..............................................................................................21
6.1 Watchdog Timer .................................................................................................................21
6.2 GPIO ...................................................................................................................................22
6.3 Hardware Monitoring .........................................................................................................23
7SystemResources ..................................................................................................24
7.1 System Memory Map .........................................................................................................24

nanoX-TC User’s ManualPage4
7.2 Direct Memory Access Channels ......................................................................................24
7.3 Legacy I/O Map ..................................................................................................................25
7.4 Interrupt Request (IRQ) Lines ...........................................................................................27
8BIOSSetupUtility ....................................................................................................30
8.1 StartingtheBIOS ................................................................................................................30
8.2 UEFIBIOSSetupNavigation .............................................................................................31
8.3 MainSetup .........................................................................................................................32
8.4 AdvancedBIOSSetup .......................................................................................................33
8.5 Chipset Configuration ........................................................................................................44
8.6 BootSetup ..........................................................................................................................47
8.7 Security Setup ....................................................................................................................48
8.8 Save&Exit .........................................................................................................................49
9BIOSCheckpoints,BeepCodes .............................................................................51
9.1 Status Code Ranges ..........................................................................................................52
9.2 Standard Status Codes .....................................................................................................52
9.3 OEM-Reserved Status Code Ranges ...............................................................................58
ImportantSafetyInstructions ......................................................................................59
GettingService .............................................................................................................60

Page 5Express-IA533 User’s Manual Page 5Express-IA533 User’s ManualnanoX-TC User’s Manual Page5
Preface
Copyright 2012 ADLINK Technology, Inc.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or other
means in any form without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior notice in order to improve
reliability, design, and function and does not represent a commitment on the part of the
manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential
damages arising out of the use or inability to use the product or documentation, even if advised
ofthepossibility ofsuchdamages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global environmental preservation
through compliance with the European Union's Restriction of Hazardous Substances (RoHS)
directiveand WasteElectrical andElectronic Equipment (WEEE) directive.Environmental
protection is a top priority forADLINK. We have enforced measures to ensure that our products,
manufacturing processes, components, and raw materials have as little impact on the
environment as possible. When products are at their end of life, our customers are encouraged to
dispose of them in accordance with the product disposal and/or recovery programs prescribed by
theirnationorcompany.
Trademarks
COM Express® and PICMG® are registered trademarks of the PCI Industrial Computer
Manufacturers Group.
Product names mentioned herein are used for identification purposes only and may be
trademarksand/orregisteredtrademarks of their respective companies.

nanoX-TC User’s ManualPage6
Conventions
Take note of the following conventions used throughout this manual to make sure that users
performcertaintasksandinstructionsproperly.
Additional information, aids, and tips that help users perform tasks.
Information to prevent minor physical injury, component damage, data
loss, and/or program corruption when trying to complete a task.
Information to prevent serious physical injury, component damage, data
loss, and/or program corruption when trying to complete a specific task.

Page 7Express-IA533 User’s Manual Page 7Express-IA533 User’s ManualnanoX-TC User’s Manual Page7
1 Introduction
1.1 Description
No bigger in size than a business card, the nanoX-TC is a COM Express™ Mini form factor
Type 10 computer-on-module that targets battery powered, mobile and handheld system
designs. The new Mini size form factor with a footprint of just 55 mm x 84 mm is the smallest
size in ADLINK's COM Express product lineup, next to the Basic size (125 mm x 95 mm) and
Compact size (95x95) form factors.
The nanoX-TC is based on the Intel® Atom™ Processor
E6xx with less than 3.9 W thermal design power (TDP).
These new 45nm Intel architecture processors implement
ground-breaking power management techniques, making
them ideal for thermally constrained and fanless embedded
applications. The Processor E6xx series offers an
integrated 2D/3D graphics engine with hardware encode/
decode, LVDS and SDVO output, HD Audio, PCI Express,
and support for Intel® Hyper-Threading and Intel®
Virtualization Technology.
The Intel® EG20T Platform Controller Hub (PCH) provides
additional I/O flexibility with SATA, UART, CAN bus, Gigabit
Ethernet and USB host/client support.
The nanoX-TC allows for innovative designs in mobile and "light" computing, including
portable and mobile equipment for the automotive and test and measurement industries,
visual communication and in the medical field. Using the Intel® Atom™ Processor E6xx and
Intel® EG20T PCH chipset, the nanoX-TC allows developers to utilize a wide variety of
mainstream software applications and middleware familiar to end users that will run
unmodified with full functionality on this platform.

nanoX-TC User’s ManualPage8
2 Specifications
2.1 Coresystem
 CPU
- Intel®Atom™ E680, 1.6 GHz, 3.9 W TDP
- Intel®Atom™ E660, 1.3 GHz, 3.3 W TDP
- Intel®Atom™ E640, 1.0 GHz, 3.3 W TDP
- Intel® Atom™ E620, 600 MHz, 2.7 W TDP
All processors support Intel® Hyper-Threading and Intel® Virtualization Technology
L2 Cache: 512 KB on all processors
Memory: Soldered 512 MB or 1 GB unbuffered DDR2 at 800 MHz
BIOS:AMIUEFIBIOS
Hardware Monitor: Supply voltages and CPU temperature
DebugInterface: XDP SFF-26 extension for ICE debug
Embedded Features: Instant on with Intel Bootloader support, OEM BIOS settings,
Board Info & Statistics,ACPI 3.0, Smart Battery Management support, Watchdog with
programmable timer ranges.
ExpansionBussestocarrierboard:
- 4 PCI Express x1 (0/1/2/3, port 0 is optionally used forEG20TPCH;
no PCIe x4 support)
- LPC Bus, SMBus (system) , I2C (user)
- 4 GPI and 4 GPO (shared with SDIO on optional EG20T)
- SPI (supports BIOS only)
2.2 Video
2D/3D Graphics Engine: Integrated in Intel® Atom™ E6xx Processor
Decoding MPEG2, MPEG4, VC1, WMV9, H.264 and DivX
Encoding MPEG4, H.264 (baseline at L3)

Page 9Express-IA533 User’s Manual Page 9Express-IA533 User’s ManualnanoX-TC User’s Manual Page9
 LVDS Interface: Single channel 18- or 24-bit pixel color depths with maximum
resolution of up to 1280x768 @ 60 Hz. Pixel clock rate
between 19.75 MHz (minimum) and 80 MHz (maximum)
SDVO: Serial digital video output supporting devices for DVI, TV-out, analog VGA.
Maximum resolution of up to 1280x1024 @ 85 Hz and pixel clock rate up to 160 MHz.
2.3 Audio
Chipset: Integrated in Intel® Atom™ Processor E6xx
Type: Multi-channel audio stream, 32-bit sample depth, sample rate up to 192 kHz
2.4 LAN
GbE MAC: Integrated in Intel® EG20T PCH
PHY: Realtek RTL8211CL
Speed: 10/100/1000 Mbps
2.5 MultiI/O
Chipset: Integrated in Intel® PCH EG20T
USB: Six USB 1.1/2.0 host ports and one USB 1.1/2.0 client port
SATA: Two ports supporting SATA 1.5 Gb/s and 3 Gb/s
SDIO Port: SDIO/MMC supporting SDHC speed class 6 (shared with GPIO)
SDIO Storage: TBD
Serial and CAN: One RS-232 (RX/TX) and one CAN (AX/RX) port (optional 2x RS-232
w/oCAN)
2.6 SuperI/O
Connected to LPC bus on carrier if needed (standard support for Winbond W83627DHG)

nanoX-TC User’s ManualPage10
2.7 SDIO/MMC Extension
 Chipset: Integrated in Intel® Controller Hub
Type: Single port SDIO/MMC supports SDIO specification 1.1 and MMC specification 4.0
Connection: Multiplexed over GPIO signals to carrier
2.8 Operating Systems
Standard Support
- Windows7
- Linux2.6.x
Extended Support (BSP)
- LinuxBSP
- AIDI I2C Library for Windows and Linux
- WinCE 6.0 / 7.0
- Windows XP Embedded
2.9 Mechanical and Environmental
Standard Operating Temperature: 0°C to 60°C
Relative Humidity: up to 90% at 55°C
Form Factor and Type: PICMG COM.0, COM Express™Type 10 compatible
Dimensions: 85 x 55 mm
2.10 PowerSpecifications
Input Power: 4.75 V – 21 V wide range, supports AT mode and ATX mode
(with additional 5 Vsb)
Power States: Supports S0, S3, S4, S5
Power Consumption: 6W at 5V typical, 5W idle
Smart Battery Support: Yes

Page 11Express-IA533 User’s Manual Page 11Express-IA533 User’s ManualnanoX-TC User’s Manual Page11
2.11 PowerConsumption
2.12 OrderingCodes
 nanoX-TC-E680-1G: Mini size COM Express Type 10 Module with Intel® Atom™ E680
processor at 1.6GHz, PCH EG20T and 1 GB DDR2 SDRAM
nanoX-TC-E660-1G: Mini size COM Express Type 10 Module with Intel® Atom™ E660
processor at 1.3GHz, PCH EG20T, and 1 GB DDR2 SDRAM
nanoX-TC-E640-1G: Mini size COM Express Type 10 Module with Intel® Atom™ E640
processor at 1.1GHz, PCH EG20T, and 1 GB DDR2 SDRAM
nanoX-TC-E620-1G: Mini size COM Express Type 10 Module with Intel® Atom™ E620
processor at 600 MHz, PCH EG20T, and 1 GB DDR2 SDRAM
12V 12V 12V 5Vsb 5Vsb
Idle WinXP Login Max Load WinXP Burnin/Kpower S1 Standby Powered On S3 Suspend to RAM S5 Soft Off
nanoX-TC-E620 (2G) 4.5 5.5 N/A 1.3 0.4
nanoX-TC-E640 (2G) 4.7 6.3 N/A 1.4 0.4
nanoX-TC-E660 (2G) 5.0 6.6 N/A 1.4 0.4
nanoX-TC-E680 (2G) 5.2 7.4 N/A 1.3 0.4
Power Consumption [W]

nanoX-TC User’s ManualPage12
3 Functional Diagram
Switch
GPIO
PCA9535
BC
AB
2x SATA (port 0,1)
SDVO
Intel®Atom™
processor
E6xx
Intel®
Platform
Controller
Hub
EG20
Soldered Memory
512 MB ~ 2 GB DDR2
3x PCIe x1 (port 1~3)
PCIe x1 (port 0)
PCIe x1 (port 0)
SMBus
18/24-bit LVDS
HDA Audio
LPC bus
4x GPI
4x GP0
SPI
SDIO/MMC port 0
I2C
BIOS
6x USB Host
1x USB Client
UART (Tx/Rx)
CAN Bus (Ax/Rx)
LAN PHY
RTL8211CL

Page 13Express-IA533 User’s Manual Page 13Express-IA533 User’s ManualnanoX-TC User’s Manual Page13
4 Mechanical Dimensions
All tolerances ± 0.05 mm
Other tolerances ± 0.2 mm
Top View
Side View
connector on
bottom side

nanoX-TC User’s ManualPage14
5 Pinout and Signal Descriptions
5.1 COM Express
™
Type 10 Pinout
All pinouts on AB connector of the nanoX-TC comply with pin-out and signal descriptions
used in the “PICMG®COM.0 R2.0: COM Express®Module Base Specification Type 2”.
This chapter details pinouts, signal descriptions, and mechanical characteristics of the
nanoX-TC.
An additional document, the “PICMG COM Express Design Guide” gives a general
introduction to carrier board designs for COM Express™modules.
The above function mappings are a generic description of COM Express pinouts,
and not necessarily supported on the module described in this manual.
55
.84.
AB
.95..125.
95
Dimensions in mm
- Gigabit Ethernet port
- LPC interface
- 4 Serial ATA channels
- AC'97 or High Definition Audio
- 6 USB 2.0 ports
- 6 PCI Express x1 Lanes
- Dual 24-bit LVDS channels
- SDVO
- GPIO / SDIO
- Keyboard
- I2C / SMBus
-SPI support
- Primary power input: +12V,
+5V standby and 3.3V RTC
AB Connector

Page 15Express-IA533 User’s Manual Page 15Express-IA533 User’s ManualnanoX-TC User’s Manual Page15
A B
A1
B1
A110
B110
5.2 Pin Definitions
Pinouts comply with
COM Express Type 10
Pin Row A Row B Pin Row A Row B
1 GND(FIXE D) GND(FIXED) 56 RSVD RSVD
2 GBE 0_ MDI3- GBE 0_ACT# 57 GND GPO2
3 GBE0_MDI3+ LPC_FRAME# 58 PCIE_TX3+ PCIE_RX3+
4 GB E 0_ LINK100# LP C _ AD0 59 PC IE _ TX3- P CIE _ RX 3-
5 GB E 0_ LINK1000# LP C_ AD1 60 G ND(F IXE D) GND(FIX E D)
6 GB E 0_ MDI2- LP C_ AD2 61 P C IE _ TX2+ P CIE _ RX 2+
7 GB E 0_ MDI2+ LP C_ AD3 62 P C IE _ TX2- P CIE _ RX 2-
8 GB E 0_ LINK # LP C_ DR Q0# 63 GPI1 GPO3
9 GB E 0_ MDI1- LP C _ DR Q1# 64 PCIE _ TX1+ PCIE _RX1+
10 GBE0_MDI1+ LPC_CLK 65 PCIE_TX1- PCIE_RX1-
11 GND(F IXE D) G ND(F IX E D) 66 G ND WAK E 0#
12 GBE0_MDI0- PWRBTN# 67 GPI2 WAKE1#
13 GBE0_MDI0+ SMB_CK 68 PCIE_TX0+ PCIE_RX0+
14 GBE0_ CTREF SMB_DAT 69 PCIE_TX0- PCIE_RX0-
15 SUS _ S 3# S MB_ ALE RT# 70 GND(FIXE D) GND(FIXE D)
16 SATA0_TX+ S ATA1_TX+ 71 LVDS_A0+ DDI0_PAIR0+
17 SATA0_TX- S ATA1_TX- 72 LVDS_A0- DDI0_PAIR0-
18 SUS_S4# SUS_ STAT# 73 LVDS _A1+ DDI0_PAIR1+
19 SATA0_RX+ S ATA1_R X+ 74 LVDS_A1- DDI0_PAIR1-
20 SATA0_RX- S ATA1_R X- 75 LVDS_A2+ DDI0_PAIR2+
21 GND(F IXE D) GND(FIXE D) 76 LVDS _ A2- DDI0_ PAIR2-
22 RSVD RSVD 77 LVDS_VDD_E N DDI0_PAIR4+
23 RS VD RSVD 78 LVDS _A3+ DDI0_PAIR4-
24 SUS_S5# PWR_OK 79 LVDS_A3- LVDS_BKLT_EN
25 R S VD R S VD 80 G ND(FIXE D) GND(F IXE D)
26 RSVD RSVD 81 LVDS_A_CK+ DDI0_PAIR3+
27 BATLOW# WDT 82 LVDS _ A_ CK- DDI0_ PAIR 3-
28 (S)ATA_ACT# AC/HDA_ SDIN2 83 LVDS_I2C_CK LVDS_BKLT_CTRL
29 AC/HDA_S YNC AC/HDA_SDIN1 84 LVDS _I2C_DAT VCC_5V_SBY
30 AC/HDA_RST# AC/HDA_SDIN0 85 GPI3 VCC_5V_SBY
31 GND(F IXE D) GND(FIXE D) 86 R SVD VCC _ 5V_S B Y
32 AC/HDA_BITCLK SPKR 87 RSVD VCC_5V_SBY
33 AC /HDA_ S DOUT I2C_ C K 88 PC IE _ CLK _ R E F + B IOS _ DIS 1#
34 BIOS_DIS0# I2C_DAT 89 PCIE_CLK_REF- DD0_HPD
35 THR MTRIP # THRM# 90 G ND(F IXE D) G ND(F IX E D)
36 USB6- USB7- 91 SPI_POWER DDI0_PAIR5+
37 USB6+ USB7+ 92 SPI_MISO DDI0_PAIR5-
38 USB_6_7_OC# USB_4_5_OC# 93 GPO0 DDI0_PAIR6+
39 USB4- USB5- 94 SPI_CLK DDI0_PAIR6-
40 USB4+ USB5+ 95 SPI_MOSI DDI0_DDC_AUX_SEL
41 GND(F IXE D) GND(FIXE D) 96 TP M_ PP R SVD
42 USB2- USB3- 97 TYPE10# SPI_CS#
43 USB2+ USB3+ 98 SE R0_TX DDI0_CTRLCLK_AUX+
44 USB_2_3_OC# USB_0_1_OC# 99 SER0_RX DDI0_CTRLDATA_AUX-
45 US B0- USB1- 100 GND(FIXE D) GND(FIXE D)
46 US B0+ USB1+ 101 SE R1_TX F AN_ PWMOUT
47 VCC_RTC E XCD1_PERST# 102 SE R1_RX FAN_ TACHIN
48 EXCD0_PE RS T# EXCD1_CPPE# 103 LID# S LEE P#
49 EXCD0_CPPE # SYS_RESET# 104 VCC_12V VCC_12V
50 LPC_SERIRQ CB_RESET# 105 VCC_12V VCC_12V
51 GND(F IXE D) G ND(F IX E D) 106 VC C _ 12V V CC _ 12V
52 RSVD RSVD 107 VCC_12V VCC_12V
53 RSVD RSVD 108 VCC_12V VCC_12V
54 GPI0 GPO1 109 VCC_12V VCC_12V
55 RSVD RSVD 110 GND
(
FIXED
)
GND
(
FIXED
)
XXX Strikethroughpinnamesindicatesthatthesignalisnotsupportedonthismodule.

nanoX-TC User’s ManualPage16
5.3 Signal Descriptions RowA
XXX Strikethroughpinnamesindicatesthatthesignalisnotsupportedonthismodule.
Pin Si
g
nal Des c ri
p
tion T
yp
ePU/PD Comment
A1 GND(FIXE D) Ground P WR - -
A2 GBE0_MDI3- EthernetMedia De
p
endent Interface - I/O - DP - -
A3 GBE 0
_
MD I3 + E therne t Me dia De
p
endent Interface + I/O - DP - -
A4 GBE0
_
LINK100
#
E thernet 100 Mbit/sec Link Indicator OD - On at 100Mb/s
A5 GBE 0_ L INK 1000# E thernet 1000 Mbit/sec Link Indicator OD - On a t 1000Mb/s
A6 GBE0_MDI2- EthernetMedia De
p
endent Interface - I/O - DP - -
A7 GBE0_MDI2+ EthernetMedia De
p
endent Interface + I/O - DP - -
A8 GBE0_LINK
#
E thernet Llink Indicator (all s
p
eeds) O-3.3 - -
A9 GBE0_MDI1- EthernetMedia De
p
endent Interface - I/O - DP - -
A10 GBE 0
_
MD I1 + E therne t Me dia De
p
endent Interface + I/O - DP - -
A11 GND
(
FIXED
)
Ground PWR - -
A12 GBE 0_MDI0- E thernet Media De
p
endent Interface - I/O - DP - -
A13 G B E 0_ MD I0+ E thernet Media De
p
endent Interface + I/O - DP - -
A14 GB E 0_ CT RE F E thernet center ta
p
re fe re nc e volta
g
eNC - not su
pp
orted
A15 SUS_S 3
#
S3Sus
p
end to RAM inidcator O-3.3 - -
A16 SATA0_TX+ S ATA 0 T ransmit Data + O - DP - -
A17 SATA0
_
TX - S ATA 0 T ransmit Data - O - DP - -
A18 SUS
_
S4
#
S4Hibernationinidcator O-3.3 - -
A19 SATA0_ RX + S ATA 0 R eceive Data + I - DP - -
A20 SATA0_R X- S ATA 0 Receive Data - I - DP - -
A21 G ND(FIXE D) Ground P WR - -
A22 RS VD Clock s
y
nc si
g
nal to Dialo
g
CLK IN - -
A23 RSVD NC - -
A24 SUS
_
S5
#
S 5 S oft Off inidcator O-3.3 - -
A25 RSVD NC - -
A26 RSVD NC - -
A27 BAT LOW# B atter
y
Low In
p
ut I-3.3 - -
A28 (S)ATA_ACT
#
S ATA L E D O-3. 3 P U 10k 3. 3V -
A29 AC /HDA_ S YNC HDA S
y
nc O-3.3 - -
A30 AC/HDA_RS T
#
HDA R es et O-3.3 - -
A31 GND
(
FIXED
)
Ground PWR - -
A32 AC/HDA
_
BITCLK HDA Clock O-3.3 - -
A33 AC/HDA_S DOUT HDA Data O-3.3 - -
A34 BIOS _ DIS 0# LPC BIOS boot device selection I-3.3 P U 10k 3.3V -
A35 THR MTRIP# C P U Thermal s hudown inidcator O-3.3 PU 1k 3.3V -
A36 US B6- US B Data - P ort6 I/O - DP - -
A37 US B6+ US B Data + Port6 I/O - DP - -
A38 USB
_
6
_
7
_
OC
#
US B OverC urrent P ort 6/7 I-3.3 P U 10k 3.3Vs b -
A39 US B4- US B Data - P ort4 I/O - DP - -
A40 US B4+ US B Data + Port4 I/O - DP - -
A41 G ND(FIXE D) Ground P WR - -
A42 US B2- US B Data - P ort2 I/O - DP - -
A43 US B2+ US B Data + Port2 I/O - DP - -
A44 USB_2_3_OC
#
US B OverC urrent P ort 2/3 I-3.3 P U 10k 3.3Vs b -
A45 US B0- US B Data - P ort0 I/O - DP - -
A46 US B0+ US B Data + Port0 I/O - DP - -
A47 VCC_RTC E xternal RTC batter
y
p
owe r P WR - -
A48 E XCD0_ PE RS T
#
Ex
p
ress Card S u
pp
ort [0]
|
card reset O-3.3 P U 10k 3.3V not su
pp
orted
A49 E XCD0_ C PPE # Ex
p
ress Card S u
pp
ort [0]
|
ca
p
. card re
q
.I-3.3 P U 10k 3.3V not su
pp
orted
A50 LPC_SERIRQ LPC INT_SERIRQ | Serial Interrupt Request IO-3.3 PU 10k 3.3V -
A51 G ND(FIXE D) Ground P WR - -
A52 RSVD NC - -
A53 RSVD NC - -
A54 GPI0 GP I0 or S DIO controller 0 data 0 IO-3.3 P U 10k 3. 3V B IOS select
A55 RSVD NC - -

Page 17Express-IA533 User’s Manual Page 17Express-IA533 User’s ManualnanoX-TC User’s Manual Page17
RowA
Signal Descriptions (cont’d)
Pin Si
g
nal Des c ri
p
tion T
yp
ePU/PD Comment
A56 RSVD NC - -
A57 G ND Ground P WR - -
A58 P CIE _ T X3+ P CIe 3 TX+ (port 0 of CP U, occupied) O - DP - used for PC H E G20T
A59 P CIE
_
T X3- P C Ie 3 TX-
(p
ort 0 of CPU
,
oc cu
p
ied
)
O - DP - used for PC H E G20T
A60 G ND(FIXE D) Ground P WR - -
A61 P CIE _ TX2+ P CIe 2 TX+ (
p
ort 3 of C P U ) O - D P - -
A62 P CIE _ TX2- P CIe 2 TX- (port 3 of CP U) O - DP - -
A63 G PI1 GP I1 or S DIO controller 0 data 1 IO-3.3 P U 10k 3. 3V B IOS select
A64 P CIE _ TX1+ P CIe 1 TX+ (port 2 of CP U) O - DP - -
A65 P CIE
_
T X1- P C Ie 1 TX-
(p
ort 2 of CPU
)
O - DP - -
A66 G ND Ground P WR - -
A67 G PI2 GP I2 or S DIO controller 0 data 2 IO-3.3 P U 10k 3. 3V B IOS select
A68 P CIE _ TX0+ P CIe 0 TX+ (port 1 of CP U) O - DP - -
A69 P CIE _ TX0- P CIe 0 TX- (
p
ort 1 of CPU) O - DP - -
A70 G ND(FIXE D) Ground P WR - -
A71 L VDS_ A0+ LVDS Channel A O - DP - -
A72 LVDS_ A0- LVDS Channel A O - DP - -
A73 LVDS
_
A1+ LVDS Channel A O - DP - -
A74 LVDS_ A1- LVDS Channel A O - DP - -
A75 L VDS_ A2+ LVDS Channel A O - DP - -
A76 LVDS_ A2- LVDS Channel A O - DP - -
A77 LVDS _ VDD_ E N LVDS VDD Panel Power O-2,5 PD 10k -
A78 L VDS_ A3+ LVDS Channel A O - DP - -
A79 LVDS
_
A3- LVDS Channel A O - DP - -
A80 G ND(FIXE D) Ground P WR - -
A81 L VDS _A_ CK+ LVDS Channel A Clock O - DP - -
A82 LVDS _A_ CK- LVDS Channel A Clock O - DP - -
A83 LVDS _ I2C _ C K L VDS I2C C lock IO-3.3 PU 2.2 k 3. 3V -
A84 LVDS_I2C_DAT LVDS I2C Data IO-3.3 PU 2.2k 3.3V -
A85 G PI3 GP I3 or S DIO controller 0 data 3 IO-3.3 P U 10k 3. 3V B IOS select
A86 RSVD NC - -
A87 RSVD NC - -
A88 PCIE_CLK_REF+ PCI Express Clock Reference O -DP - -
A89 PCIE_CLK_REF- PCI Ex
p
ress Clock Reference O - DP - -
A90 G ND(FIXE D) Ground P WR - -
A91 S PI_ POWE R P ower source for SPI devices on carrier P WR - -
A92 S P I_ MIS O Da ta in to Module from C a rrier S P I I-3. 3 -
A93 GPO0 GP O0 or S DIO controller 0 clock O-3.3 P U 10k 3.3V B IOS select
A94 SPI_CLK Clock from Module to Carrier SPI O-3.3 -
A95 S PI_ MOS I Data out from Module to C arrier SPI O-3.3 -
A96 TPM_PP (TPM) Physical Presence pin I-3.3 -
A97 TYP E 10
#
Rev 2.0 /T
yp
e 10 indicator to ca rrier S TO PD 4.7k -
A98 S E R0_ TX S erial 0 port trans mitter O-5 -
A99 SE R0_R X S erial 0
p
ort rec eive r I-5 -
A100 G ND(FIXE D) Ground P WR - -
A101 SE R 1_ TX S erial 1 port trans mitter / or CAN CAN_ AX O-5 -
A102 SE R1_RX S erial 1 port receiver / or CAN CAN_ RX I-5 -
A103 L ID# ACPI type LID switch I-3.3 PU 4.7k 3.3V
A104 VC C_ 12V P ower 12V P WR - -
A105 VC C_ 12V P ower 12V P WR - -
A106 VC C_ 12V P ower 12V P WR - -
A107 VC C_ 12V P ower 12V P WR - -
A108 VC C_ 12V P ower 12V P WR - -
A109 VC C_ 12V P ower 12V P WR - -
A110 G ND(FIXE D) Ground P WR - -
XXX Strikethroughpinnamesindicatesthatthesignalisnotsupportedonthismodule.

nanoX-TC User’s ManualPage18
RowB
Signal Descriptions (cont’d)
XXX Strikethroughpinnamesindicatesthatthesignalisnotsupportedonthismodule.
Pin Si
g
nal Des cri
p
tion T
yp
e PU/PD Comment
B 1 GND(F IXE D) Ground PWR - -
B2 GBE0_ACT
#
EthernetActivit
y
LED OD - -
B3 LPC
_
FRAME# LPC Frame Indicator O-3.3 - -
B4 LPC
_
AD0 L PC multi
p
lexed Adress & DATA B us IO-3.3 - -
B5 LPC_AD1 LPC multi
p
lexed Adress & DATA B us IO-3.3 - -
B6 LPC_AD2 LPC multi
p
lexed Adress & DATA B us IO-3.3 - -
B7 LPC_AD3 LPC multi
p
lexed Adress & DATA B us IO-3.3 - -
B8 LPC_DR
Q
0
#
LPC Serial DMA Re
q
uest 0 I-3.3 - not s u
pp
orted
B9 LPC_DR
Q
1
#
LPC Serial DMA Re
q
uest 1 I-3.3 - not s u
pp
orted
B10 LPC
_
CLK LPC Clock O-3.3 - -
B11 GND
(
FIXED
)
Ground PWR - -
B12 PWRBTN
#
P ower Button I-3.3 PU 10K 3.3Vs b -
B 13 S MB _ C K S MB us C loc k IO -3 .3 P U 2 k2 3 . 3 Vs b -
B14 SMB_DAT SMBus Data IO-3.3 PU 2k2 3.3Vsb -
B15 SMB_ALERT
#
S
y
stem Mana
g
ement Bus Alert for S MI I-3.3 PU 10k 3.3V
B16 SATA1_TX + S ATA 1 T ransmit Data + O - DP - -
B17 SATA1
_
TX - S AT A 1 T ransmit Data - O - DP - -
B18 SUS
_
STAT# Imminent sus
p
end o
p
eration inidcator O-3.3 - not su
pp
orted
B19 SATA1_RX + S ATA 1 R eceive Data + I - DP - -
B20 SATA1
_
R X - S ATA 1 R eceive Da ta - I - DP - -
B21 GND
(
FIXED
)
Ground PWR - -
B22 RSVD NC --
B23 RSVD NC --
B24 PWR_OK Power OK from main
p
ower s u
pp
l
y
I-3.3 - alwa
y
s reserve
p
ull u
p
B25 RSVD NC --
B26 RSVD NC --
B27 WDT Watch Do
g
E vent occurred indicator O-3.3 PU 10K 3.3Vs b
B28 AC/HDA
_
SDIN2 SerialTDMdata in
p
ut 2 I-3. 3 - not s u
pp
orted
B29 AC/HDA _ S DIN1 S erial T DM data in
p
ut 1 I-3. 3 - -
B30 AC/HDA _ S DIN0 S erial T DM data in
p
ut 0 I-3. 3 - -
B31 GND(FIXED) Ground PWR - -
B32 SPKR Out
p
ut for audio enunciator (P C B ee
p
)O-3.3- -
B33 I2C_CK General
p
ur
p
os e I2C
p
ort cloc k out
p
ut IO-3.3 PU 4k7 3.3V
B34 I2C
_
DAT General
p
ur
p
os e I2C
p
ort data I
/
O line IO-3.3 PU 4k7 3.3V
B35 THRM
#
Off module over tem
p
erature indicator I-3.3 PU 1k2 3.3V -
B 36 US B 7- US B Data - P ort7 I/O - DP - clie nt
p
ort
B37 US B7+ US B Data + Port7 I/O - DP - client
p
ort
B38 USB_4_5_OC
#
US B OverC urrent Port 4,5 I-3.3 PU 10k 3.3Vsb -
B 39 US B5- US B Data- P ort5 I/O - DP - -
B40 US B5+ US B Data+ Port5 I/O - DP - -
B41 GND
(
FIXED
)
Ground I-3.3 - -
B 42 US B3- US B Data- P ort3 I/O - DP - -
B43 US B3+ US B Data+ Port3 I/O - DP - -
B44 USB_0_1_OC
#
US B OverC urrent Port 0,1 I-3.3 PU 10k 3.3Vsb -
B 45 US B1- US B Data- P ort1 I/O - DP - -
B46 US B1+ US B Data+ Port1 I/O - DP - -
B47 E XCD1_PE RST
#
PCIEx
p
ress Card Resetsi
g
na l O-3.3 - notsu
pp
orted
B48 EXCD1
_
CPPE# PCI Ex
p
ress ca
p
a ble ca rd re
q
ue st O-3.3 - not su
pp
orted
B49 SYS
_
RESET# ResetButton In
p
ut I-3.3 none 3.3Vsb
B50 CB_RESET# Resetoutput fromModule to Carrier Board O-3.3 - -
B51 GND(FIXED) Ground PWR - -
B52 RSVD NC - -
B53 RSVD NC - -
B54 GPO1 GP O1 or S DIO contr. 0 Command/R esponse IO-3.3 PU 10k 3.3V BIOS select
B55 RSVD NC - -

Page 19Express-IA533 User’s Manual Page 19Express-IA533 User’s ManualnanoX-TC User’s Manual Page19
RowB
Signal Descriptions (cont’d)
XXX Strikethroughpinnamesindicatesthatthesignalisnotsupportedonthismodule.
Pin Si
g
nal Des c ri
p
tion T
yp
ePU/PD Comment
B56 RSVD NC - -
B57 GPO2 GP O2 or S DIO controller 0 Write Protec
t
IO-3.3 PU 10k 3.3V BIOS select
B58 P CIE _R X3+ P C Ie 3 R X+ (port 0 of C P U, occupied) I - DP - us ed for P CH E G20T
B59 PCIE
_
RX3- PCIe 3 RX-
(p
ort 0 of C PU
,
occ u
p
ied
)
I - DP - used for PCH E G20T
B60 GND(FIXED) Ground PWR - -
B61 P C IE _ R X 2+ P C Ie 2 R X+ (
p
ort 3 of C P U) I - DP - -
B62 P C IE _ R X2- P CIe 2 R X- (port 3 of C PU) I - DP - -
B63 GPO3 GP O3 or S DIO controller 0 Card Detect IO-3.3 PU 10k 3.3V B IOS s elect
B64 P CIE _R X 1+ P C Ie 1 R X+ (port 2 of C P U) I - DP - remove LAN to us e
B65 PCIE
_
RX1- PCIe 1 RX-
(p
ort 2 of C PU
)
I - DP - remove LAN to use
B 66 WAKE 0# P C I E x pres s wake up signal. I-3. 3 none 3.3Vs b connected to WA KE 1
#
B67 WAKE 1# General Pur
p
os e wake u
p
si
g
na l I-3. 3 none 3.3Vs b connected to WA KE 0
#
B68 P C IE _R X 0+ P C Ie 0 R X+ (port 1 of CP U) I - DP -
B69 PCIE_RX0- PCIe 0 RX-(
p
ort 1 of C PU) I - DP -
B70 GND(FIXED) Ground PWR - -
B71 DDI0_PAIR0+ SDVOB_RED
+
O - DP - -
B72 DDI0_PAIR0- SDVOB_RED- O -DP - -
B73 DDI0
_
PAIR1+ SDVOB
_
GRN+ O - DP - -
B74 DDI0_PAIR1- SDVOB_GRN- O - DP - -
B75 DDI0_PAIR2+ SDVOB_BLU+ O -DP - -
B76 DDI0_PAIR2- SDVOB_BLU- O -DP - -
B77 DDI0_PAIR4+ SDVOB_INT+ I - DP - -
B78 DDI0_ PAIR4- S DVOB_ INT- I - DP - -
B79 LVDS
_
BKLT
_
EN LVDS
p
anel backli
g
ht enable O-3.3 PD 100k -
B80 GND(FIXED) Ground PWR - -
B81 DDI0_PAIR3+ SDVOB_CK+ O -DP - -
B82 DDI0_PAIR3- SDVOB_CK O -DP - -
B83 LVDS_BKLT_CTRL LVDS
p
anel backli
g
ht bri
g
htness control O-3.3 PD 10k -
B84 VCC_5V_SBY 5V Standby Input PWR - -
B85 VCC_5V_SBY 5V Standb
y
In
p
ut P WR - -
B86 VCC_5V_SBY 5V Standby Input PWR - -
B87 VCC
_
5V
_
SBY 5V Standb
y
In
p
ut P WR - -
B88 BIOS_DIS1# SPI BIOS bootdevice selection I-3.3 PU 10k 3.3Vsb -
B89 DD0_HPD Di
g
ita l Dis
p
la
y
Interfac e Hot-P lu
g
Detec
t
I-3.3 PU 10k 3.3V not needed on S DVO
B90 GND(FIXED) Ground PWR - -
B91 DDI0_ PAIR5+ S DVO_ TVCLKIN+ I - DP - -
B92 DDI0_ PAIR5- S DVO_ TVCLKIN- I - DP - -
B93 DDI0
_
PAIR6+ SDVO
_
FLDS TALL+ I - DP - -
B94 DDI0_PAIR6- SDVO_FLDSTALL- I-DP - -
B95 DDI0_DDC_AUX_SEL S elect function of DDI(0) CT R L_ CLK_AUX+ IO-3.3 - -
B96 RSVD NC - -
B97 SPI_CS
#
Chi
p
s e le ct for C a rrier B oa rd S P I O -3. 3 none 3 .3 Vs b -
B98 DDI0_CTRLCLK_AUX+ SDVOI2C Clock IO-2.5
B99 DDI0_CTRLDATA_AUX- SDVO I2C Data IO-2.5
B100 GND(FIXE D) Ground PWR - -
B101 FAN_ P WMOUT Fan s peed control output O-3.3 P U 1.2K 3.3V sb
B102 FAN_T ACHIN Fan tachometer input I-3.3 PD 10k -
B103 S LE E P # s leep I-3.3 - -
B104 VC C_ 12V P ower 12V PWR - -
B105 VC C_ 12V P ower 12V PWR - -
B106 VC C_ 12V P ower 12V PWR - -
B107 VC C_ 12V P ower 12V PWR - -
B108 VC C_ 12V P ower 12V PWR - -
B109 VC C_ 12V P ower 12V PWR - -
B110 GND(FIXE D) Ground PWR - -

nanoX-TC User’s ManualPage20
Signal Description Legend
IO-2,5 Bi-directional 2,5 V Input/Output
IO-3,3 Bi-directional 3,3 V Input/Output
IO-5 Bi-directional 5 V Input/Output
I-3,3 3,3 V Input
I-5 5 V Input
O-2,5 2,5 V Output
O-3,3 3,3 V Output
O-5 5 V Output
IO Input/Output
OA Analog Output
OD Digital Output
I/O - DP Differential Pair Input/Output
O - DP Differential Pair Output
I - DP Differential Pair Input
PWR Power or Ground
STO Strapping Output
PU Pull Up Resistor
PD Pull Down Resistor
NC Not Connected / Reserved
Signal Type Legend