ADLINK Technology cPCI-3510 User manual

Advance Technologies; Automate the World.
Manual Rev.: 2.02
Revision Date: December 11, 2015
Part No: 50-15095-1020
cPCI-3510(BL) Series
Performance 3U CompactPCI® PlusIO
Intel® Core™ i7/i5 Processor Blade
User’s Manual

ii Revision History
Revision History
Revision Release Date Description of Change(s)
2.00 26/03/2014 Initial release
2.01 17/11/2014 Correct Block Diagram SATA device support
2.02 11/12/2015 Add 5th Gen Intel ® Core™ “BL” SKUs;
minor corrections

Preface iii
cPCI-3510(BL)
Preface
Copyright 2014-15 ADLINK Technology Inc.
This document contains proprietary information protected by copy-
right. All rights are reserved. No part of this manual may be repro-
duced by any mechanical, electronic, or other means in any form
without prior written permission of the manufacturer.
Disclaimer
The information in this document is subject to change without prior
notice in order to improve reliability, design, and function and does
not represent a commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, spe-
cial, incidental, or consequential damages arising out of the use or
inability to use the product or documentation, even if advised of
the possibility of such damages.
Environmental Responsibility
ADLINK is committed to fulfill its social responsibility to global
environmental preservation through compliance with the Euro-
pean Union's Restriction of Hazardous Substances (RoHS) direc-
tive and Waste Electrical and Electronic Equipment (WEEE)
directive. Environmental protection is a top priority for ADLINK.
We have enforced measures to ensure that our products, manu-
facturing processes, components, and raw materials have as little
impact on the environment as possible. When products are at their
end of life, our customers are encouraged to dispose of them in
accordance with the product disposal and/or recovery programs
prescribed by their nation or company.
Trademarks
Product names mentioned herein are used for identification pur-
poses only and may be trademarks and/or registered trademarks
of their respective companies.

iv Preface
Conventions
Take note of the following conventions used throughout this
manual to make sure that users perform certain tasks and
instructions properly.
NOTE:
NOTE:
Additional information, aids, and tips that help users perform
tasks.
CAUTION:
Information to prevent minor physical injury, component dam-
age, data loss, and/or program corruption when trying to com-
plete a task.
WARNING:
Information to prevent serious physical injury, component
damage, data loss, and/or program corruption when trying to
complete a specific task.

Table of Contents v
cPCI-3510(BL)
Table of Contents
Revision History...................................................................... ii
Preface.................................................................................... iii
List of Figures........................................................................ ix
List of Tables.......................................................................... xi
1 Introduction ........................................................................ 1
1.1 Overview.............................................................................. 1
1.2 Features............................................................................... 2
1.3 Model Number Decoder....................................................... 3
1.4 Package Contents ............................................................... 5
2 Specifications..................................................................... 7
2.1 cPCI-3510(BL) Processor Blade Specifications .................. 7
2.2 cPCI-R3P00(T) RTM Specifications.................................. 11
2.3 Block Diagrams.................................................................. 12
2.4 I/O Connectivity Table ....................................................... 19
2.5 Power Requirements......................................................... 21
3 Functional Description .................................................... 23
3.1 Processors......................................................................... 23
3.2 Platform Controller Hub ..................................................... 25
3.3 PMC/XMC.......................................................................... 25
3.4 Intel® Turbo Boost Technology......................................... 26
3.5 Intel® Hyper-Threading Technology.................................. 26
3.6 Trusted Platform Module ................................................... 26
3.7 Battery ............................................................................... 27
4 Board Interfaces............................................................... 29

vi Table of Contents
4.1 cPCI-3510(BL) Series Board Layout.................................. 29
4.2 cPCI-3510(BL) Blade Assembly Layout............................. 31
4.3 cPCI-3510(BL)D Blade Assembly Layout.......................... 32
4.4 cPCI-3510(BL)G Blade Assembly Layout.......................... 33
4.5 cPCI-3510L Blade Assembly Layout ................................. 34
4.6 cPCI-3510M Blade Assembly Layout ................................ 35
4.7 cPCI-3510(BL)/D/G Faceplate........................................... 36
4.8 cPCI-3510L, cPCI-3510M Faceplate................................. 37
4.9 cPCI-R3P00(T) RTM Board Layout................................... 39
4.10 cPCI-R3P00(T) RTM Faceplate......................................... 40
4.11 Connector Pin Assignments............................................... 41
4.12 Jumper Settings................................................................. 66
5 Getting Started.................................................................. 67
5.1 CPU and Heatsink ............................................................. 67
5.2 SATA Drive Installation...................................................... 68
5.3 Installing a CFast Card ...................................................... 71
5.4 Installing the cPCI-3510(BL) to the Chassis...................... 72
5.5 RTM Installation - cPCI-R3P00(T)..................................... 73
6 Driver Installation.............................................................. 75
6.1 cPCI-3510(BL) Drivers....................................................... 75
6.2 Ethernet Controller Driver.................................................. 76
6.3 USB-to-Serial Converter Driver (RTM) .............................. 78
7 Watchdog Timer................................................................ 81
7.1 Setting the Watchdog by IPMI Commands........................ 81
8 BIOS Setup Utility............................................................. 87
8.1 Starting the BIOS............................................................... 87
8.2 Main Setup......................................................................... 92
8.3 Advanced BIOS Setup....................................................... 93
8.3.1 ACPI Settings ................................................................94
8.3.2 Trusted Computing ........................................................95

Table of Contents vii
cPCI-3510(BL)
8.3.3 CPU Configuration.........................................................96
8.3.4 SATA Configuration.......................................................97
8.3.5 PCH-FW Configuration..................................................98
8.3.6 Intel ® Anti-Theft Technology Configuration..................99
8.3.7 AMT Configuration.......................................................100
8.3.8 USB Configuration.......................................................101
8.3.9 Hardware Monitor........................................................102
8.3.10Super IO Configuration................................................103
8.3.11Console Redirection ....................................................105
8.4 Chipset Setup.................................................................. 108
8.4.1 PCH-IO Configuration..................................................109
8.4.2 System Agent (SA) Configuration................................112
8.5 Boot Settings ................................................................... 116
8.5.1 CSM Parameter...........................................................117
8.6 Security Setup ................................................................. 119
8.7 Save & Exit Menu............................................................ 120
9 IPMI User Guide.............................................................. 123
9.1 Introduction...................................................................... 123
9.2 Summary of Commands Supported by BMR-AVR-cPCI. 123
9.3 OEM Commands Summary Table................................... 125
9.4 CompactPCI Address Map .............................................. 128
9.5 Communications with IPMC............................................. 129
9.6 IPMI Sensors List............................................................. 129
9.7 Relevant Documents ....................................................... 130
Important Safety Instructions............................................ 131
Getting Service.................................................................... 133

viii Table of Contents
This page intentionally left blank.

List of Figures ix
cPCI-3510(BL)
List of Figures
Figure 2-1: cPCI-3510(BL) Blade Functional Block Diagram...........12
Figure 2-2: cPCI-3510(BL)D Daughter Board Func. Block Diagram13
Figure 2-3: cPCI-3510(BL)G Daughter Board Func. Block Diagram14
Figure 2-4: cPCI-3510L Daughter Board Func. Block Diagram.......15
Figure 2-5: cPCI-3510M Daughter Board Func. Block Diagram......16
Figure 2-6: cPCI-R3P00 RTM Functional Block Diagram................17
Figure 2-7: cPCI-R3P00T RTM Functional Block Diagram..............18
Figure 4-1: cPCI-3510(BL) Series Board Layout (comp. side).........29
Figure 4-2: cPCI-3510(BL) Series Board Layout (solder side).........30
Figure 4-3: cPCI-3510(BL) Blade Assembly Layout ........................31
Figure 4-4: cPCI-3510(BL)D Blade Assembly Layout......................32
Figure 4-5: cPCI-3510(BL)G Blade Assembly Layout......................33
Figure 4-6: cPCI-3510L Blade Assembly Layout.............................34
Figure 4-7: cPCI-3510M Blade Assembly Layout............................35
Figure 4-8: cPCI-3510(BL)/D/G Faceplate Layout...........................36
Figure 4-9: cPCI-3510L/M Faceplate Layout...................................37
Figure 4-10: cPCI-R3P00(T) RTM Board Layout...............................39
Figure 4-11: cPCI-R3P00(T) RTM Faceplate.....................................40
Figure 7-1: Example procedure for configuring the WDT.................85

xListofFigures
This page intentionally left blank.

List of Tables xi
cPCI-3510(BL)
List of Tables
Table 2-1: cPCI-3510(BL) Processor Blade Specifications ..............7
Table 2-2: cPCI-R3P00(T) RTM Specifications..............................11
Table 2-3: cPCI-3510(BL) I/O Connectivity.....................................19
Table 4-1: cPCI-3510(BL) Faceplate System LED Descriptions ....38
Table 4-2: USB 2.0 Pin Definition...................................................41
Table 4-3: VGA Pin Definition.........................................................42
Table 4-4: DisplayPort Pin Definition..............................................42
Table 4-5: DVI-I Connector Pin Definition.......................................43
Table 4-6: RJ-45 GbE Pin Definitions.............................................44
Table 4-7: LAN LED Status Definitions...........................................44
Table 4-8: PS/2 Keyboard/Mouse Pin Definition.............................45
Table 4-9: cPCI-3510(BL)D/P COM1 (DB-9) Pin Definition............45
Table 4-10: cPCI-3510(BL)D/P COM1 Mode Switch Settings..........46
Table 4-11: cPCI-3510(BL)G COM1 (RJ-45) Pin Definition..............47
Table 4-12: cPCI-3510(BL)G COM1 (DB-9 adapter) Pin Definition..47
Table 4-13: RS-422/485 Adapter Dongle Pin Definition ...................48
Table 4-14: cPCI-3510(BL)G COM1 RS-422/485 Dongle Pin Def...48
Table 4-15: cPCI-3510(BL)G COM2 Pin Header Definition..............49
Table 4-16: cPCI-R3P00(T) RTM COM4 Pin Definition....................49
Table 4-17: cPCI-R3P00(T) COM5 Pin Definition.............................50
Table 4-18: cPCI-R3P00(T) COM5 RS-422/485 Dongle Pin Def’n...50
Table 4-19: cPCI-3510M 100-pin I/O Connector Pin Definition........51
Table 4-20: SATA Connector on RTM..............................................53
Table 4-21: SATA on cPCI-3510(BL)D/G/M DB Pin Def’n................53
Table 4-22: CFast Socket Pin Definition...........................................54
Table 4-23: Layer-2 Daughter Board Connector Pin Definition ........55
Table 4-24: Storage Daughter Board Connector Pin Definition........56
Table 4-25: cPCI-3510(BL)G DB Connector Pin Definition ..............57
Table 4-26: PMC/XMC Daughter Board Connector Pin Definition....58
Table 4-27: PMC Connector Pin Definitions.....................................59
Table 4-28: XMC Connector Pin Definition.......................................61
Table 4-29: CompactPCI J1 Connector Pin Definition......................62
Table 4-30: CompactPCI J2 Connector Pin Definition......................63
Table 4-31: cPCI-R3P00 rJ2 Connector Pin Definition.....................64
Table 4-32: cPCI-R3P00T rJ2 Connector Pin Definition...................65
Table 4-33: Load BIOS Default Jumper Settings..............................66
Table 4-34: XMC VPWR Select Jumper Settings.............................66
Table 4-35: PMC V(I/O) Select Jumper Settings..............................66

xii List of Tables
This page intentionally left blank.

Introduction 1
cPCI-3510(BL)
1 Introduction
1.1 Overview
The ADLINK cPCI-3510(BL) Series is a 3U CompactPCI® PlusIO
compatible processor blade with soldered DDR3L-1333/1600
ECC memory up to 16GB. The ADLINK cPCI-3510(BL) features
an Intel® Core™ i7 processor with Mobile Intel® QM87 Express
Chipset.
The cPCI-3510(BL) Series is a 3U CompactPCI blade available in
single-slot (4HP), dual-slot (8HP) or triple-slot (12HP) width form
factors with various daughter boards to provide a broad range of
I/O requirements. Faceplate I/O in the single-slot (4HP) version
includes 1x DVI-I, 2x GbE and 1x USB 3.0 port (these I/O are
common to all versions). Faceplate I/O in the dual-slot (8HP) ver-
sion includes additional 2x USB 2.0, 1x COM, 1x KB/MS and
Line-in/Line-out on the cPCI-3510(BL)D or additional 2x Display-
Ports, 1x COM in RJ-45 connector, 1x KB/MS and 1x additional
USB2.0 port on the cPCI-3510(BL)G. Two more dual-slot options
are the cPCI-3510L with additional 2x GbE, 1x COM and 2x USB
and the cPCI-3510M with one 100-pin high density connector sup-
porting additional 2x DVI-I/DP, 2x USB 2.0, 2x COM, 2x KB/MS
and Line-in/Line-out ports.
Graphics support is integrated on the CPU and allows 3 indepen-
dent displays on the faceplate by selecting the cPCI-3510(BL)G
with additional 2x DisplayPorts. Storage includes a CFast slot,
mSATA socket or a 32GB onboard SSD and 2.5" SATA drive on
the layer 2 daughter board (cPCI-3510(BL)D/P/L/M). One optional
PCI 32-bit/66 MHz PMC site or PCIe x1 XMC site is available on
the 8HP or 12HP versions (cPCI-3510S or cPCI-3510P).
Rear I/O signals to J2 include 4x PCIe x1, 3x SATA 3 Gb/s, and 3x
USB 2.0. GPIO and SMBus signals are also routed to the J2 con-
nector. The optional Rear Transition Module (RTM) provides 3x
SATA, 2x GbE, 2x USB, 1x COM (Tx/Rx) and 1x VGA port.
The cPCI-3510(BL) is a high performance solution for factory
automation and other industrial applications that require superior
data transfer capability and advanced computing power. The
ADLINK cPCI-3510(BL) provides high manageability, supports

2Introduction
Satellite mode operation as a standalone blade in peripheral slots,
and IPMI for system health monitoring. A GbE port on the face-
plate supports Intel® AMT 9.0 for remote monitoring.
1.2 Features
X3U CompactPCI blade in 4HP, 8HP or 12HP width form factor
X4th/5th Generation Intel® Core™ Processor
XGraphics and memory controllers integrated in processor
XCompatible with PICMG 2.30 PlusIO (3x SATA, 4x PCIe x1, 3x
USB, 2x GbE to J2)
XDual channel DDR3L-1333/1600 soldered SDRAM with ECC,
up to 16GB
X32-bit, 33/66MHz CompactPCI Interface based on PCI specifi-
cations, universal V(I/O)
XSupports Satellite mode operation as a standalone blade in
peripheral slots
XOptional 32-bit/66MHz PMC or PCIe x1 XMC site
XSupports IPMI for system health monitoring
XDVI-I port on front with VGA switchable to rear I/O by BIOS set-
ting
XAdditional two DisplayPorts on layer 2 daughter board
(cPCI-3510(BL)G)
X Supports 3 independent displays with DirectX 11.1, OpenGL 3.2
XTwo PCIe Gigabit Ethernet egress ports, one supporting Intel
iAMT 9.0
XTwo additional PCIe Gigabit Ethernet Controllers routed to
RTM (cPCI-R3P00)
XAdditional two Gigabit Ethernet ports on 80mm RTM
(cPCI-R3P00T)
XLine-in and Line-out ports on faceplate (cPCI-3510(BL)D)
XCFast or mSATA socket for SATA interface storage
XOptional onboard SSD for SATA interface storage (shares
space with CFast socket)
X2.5" SATA connector on 8HP/12HP versions at 6 Gb/s
(cPCI-3510(BL)D/(BL)G/M/L)

Introduction 3
cPCI-3510(BL)
1.3 Model Number Decoder
Blades
(A) Operating Temperature Code
Z Blank = -20°C to +70°C
Z EX = -40°C to +85°C (for CPUs with TDP below 37W only)
(B) J2 Connector Type Code
Z0= HM connector
Z1= UHM connector (PICMG 2.30 PlusIO compliant)
(C) Configuration Code
ZBlank = Single slot width with CFast socket, 1x DVI-I, 1x
USB 3.0, 2x GbE
ZD= Dual slot width with CFast socket, 1x DVI-I, 1x USB 3.0,
2x GbE on layer 1; 2x USB 2.0, COM (RS-232/422/485),
PS/2 KB/MS, Line-in, Line-out ports and 2.5" SATA drive
space on layer 2
ZG= Dual slot width with CFast socket, 1x DVI-I, 1x USB 3.0,
2x GbE on layer 1; 2x DisplayPort, RJ-45 COM
(RS-232/422/485), PS/2 KB/MS, USB 2.0 ports, onboard
SATA connector and 2.5" SATA drive space on layer 2
ZL= Dual slot width with CFast socket, 1x DVI-I, 1x USB 3.0,
2x GbE on layer 1; 2x GbE, 1x DB-9 COM
(RS-232/422/485), 1x USB 2.0 on faceplate, 1x onboard
USB 2.0 port and 2.5" SATA drive space on layer 2
ZM= Dual slot width with CFast socket, 1x DVI-I, 1x USB 3.0,
2x GbE on layer 1; 1x 100-pin high density connector sup-
ports, 2x DVI/DP, 2x USB 2.0, 2x COM (RS-232/422/485),
1x KB/MS, audio and 2.5" SATA drive space on layer 2
ZS= Dual slot width with CFast socket, 1x DVI-I, 1x USB 3.0,
2x GbE on layer 1; PMC/XMC site on layer 2
ZP=Triple slot width with CFast socket, 1x DVI-I, 1x USB 3.0,
2x GbE on layer 1; 2x USB 2.0, COM (RS-232/422/485),
PS/2 KB/MS, Line-in, Line-out ports and 2.5" SATA drive
space on layer 2; PMC/XMC site on layer 3
cPCI-EX 3510D/ 4700E / M4G / S32
(A) (B)(C) (D) (E) (F)

4Introduction
(D) CPU Code
Z5700E = quad-core Intel® CoreTM i7-5700EQ processor
Z4700E = quad-core Intel® CoreTM i7-4700EQ processor
Z4402E = dual-core Intel® CoreTM i5-4402E processor
(E) Memory Size Code
ZM4 = 2x 2GB DDR3L-1600 soldered SDRAM
ZM8 = 2x 4GB DDR3L-1600 soldered SDRAM
ZM16 = 2x 8GB DDR3L-1333 soldered SDRAM
(F) Storage Board Code
ZBlank = Default with CFast socket
ZMS = Equipped with mSATA socket
ZS32 = Onboard soldered 32GB SSD
RTMs
(A) Model Code
ZBlank = dual slot width, 50mm depth 3U RTM with 2x COM,
2x USB, 3x SATA, VGA, 2x GbE (switched from front CPU
blade)
ZT = dual slot width, 80mm depth 3U RTM with 2x COM, 2x
USB, 3x SATA, VGA, 2x GbE (independent from front CPU
blade)
cPCI- R3P00 T
(A)

Introduction 5
cPCI-3510(BL)
1.4 Package Contents
The cPCI-3510(BL) is packaged with the following components. If
any of the following items are missing or damaged, retain the ship-
ping carton and packing material and contact the dealer for
inspection. Please obtain authorization before returning any prod-
uct to ADLINK. The packing contents of cPCI-3510(BL) Series
non-standard configurations will vary depending on customer
requests.
Processor Blade
XThe cPCI-3510(BL) Series Processor Blade
ZCPU and memory specifications will differ depending on
options selected
ZThermal module is assembled on the board
XY-cable for PS/2 combo port (cPCI-3510(BL)D/P only)
X2.5" SATA drive installation kit
(cPCI-3510(BL)D/(BL)G/L/M/P only)
XRJ-45 to DB-9 COM adapter cable (cPCI-3510(BL)G version
only)
XDisplayPort to DVI adapter cable (cPCI-3510(BL)G version
only)
XUser’s manual
Rear Transition Module
XcPCI-R3P00 or cPCI-R3P00T RTM
NOTE:
NOTE:
No I/O cables are included with the cPCI-3510M version.
NOTE:
NOTE:
The contents of non-standard cPCI-3510(BL) configurations
may vary depending on the customer’s requirements.

6Introduction
Blade Optional Accessories
X2.5” SATA drive installation kit (P/N 58-00176-0000)
XY-cable for PS/2 combo port (P/N 30-01016-2000)
XRJ-45 to DB-9 COM adapter cable (P/N 30-01020-0200)
XDisplayPort to DVI adapter cable (P/N 30-01120-0000)
XDisplayPort to VGA adapter cable (P/N 30-01119-0000)
XDisplayPort to HDMI adapter cable (P/N 30-01121-0000)
XUSB 3.0 Type A male-to-female extension cable
(P/N: 30-01175-0000)
XSCSI 100-pin IO cable: 2x DVI-D female, 2x DB9 male,
2x USB female, 2x PS/2 female, 2x audio jack
(available by request)
CAUTION:
This product must be protected from static discharge and phys-
ical shock. Never remove any of the components except at a
static-free workstation. Use the anti-static bag shipped with the
product when putting the board on a surface. Wear an
anti-static wrist strap properly grounded on one of the system's
ESD ground jacks when installing or servicing system compo-
nents.

Specifications 7
cPCI-3510(BL)
2 Specifications
2.1 cPCI-3510(BL) Processor Blade Specifications
CompactPCI®
Standards • PICMG® 2.0 CompactPCI® Rev. 3.0 • PICMG® 2.1 Hot Swap Specification Rev. 2.0
• PICMG® 2.9 System Management Rev. 1.0
• PICMG® 2.30 CompactPCI® PlusIO
Mechanical • Standard 3U CompactPCI®
• Board size: 100mm x 160mm
• Single slot (4HP, 20.32mm); Dual slot (8HP, 40.64mm); Triple-slot
(12HP, 60.96 mm)
• CompactPCI® with HM type J1 connector, UHM type J2
connector
Processor • 4-core Intel® Core™ i7-5700EQ Processor 2.6GHz, 3.4GHz
Turbo, 6M cache, 47/37W by cTDP (cPCI-3510BL only)
• 4-core Intel® Core™ i7-4700EQ Processor 2.4GHz, 3.4GHz
Turbo, 6M cache, 47/37W by cTDP
• 2-core Intel® Core™ i5-4402E Processor 1.6GHz, 2.7GHz Turbo,
3M cache, 25W
• Passive heatsink
Chipset • Mobile Intel® QM87 Express Chipset
Memory • DDR3L-1333 SDRAM ECC soldered, up to 16GB (cPCI-3510BL)
• DDR3L-1600 SDRAM ECC soldered, up to 8GB (cPCI-3510)
CompactPCI
Bus • PCI 32bit/ 33MHz; 3.3V, 5V universal V(IO) • Supports operation in system slot as master or in peripheral slot
as standalone blade without connectivity to CompactPCI bus
(Satellite mode)
Gigabit
Ethernet • One PCIe x1 Intel® I217 GbE PHY and three PCIe x1 Intel® I210 Gigabit Ethernet controllers
• Two egress 10/100/1000BASE-T ports on faceplate, one
supporting Intel® AMT 9.0 by I217 controller
• Two egress 10/100/1000BASE-T ports routed to rear transition
module
Graphics • Integrated on Intel® Core™ processor
• DVI-I port on faceplate, VGA switchable to J2 (RTM) by BIOS
setting
• Analog monitor support up to QXGA 2048x1536 @75Hz, 32-bit
• Two DisplayPorts on faceplate with resolution up to 2560x1440
@60Hz (cPCI-3510(BL)G only)
• Up to three independent display
Table 2-1: cPCI-3510(BL) Processor Blade Specifications

8 Specifications
USB • Up to three USB faceplate ports
Serial Ports • Up to four serial ports
• One RS-232/422/485 serial port on 8HP faceplate
(cPCI-3510(BL)D/(BL)G/L)
• Additional RS-232 10-pin header on layer-2 board
(cPCI-3510(BL)G only)
• Up to two RS-232/422/485 COM port (cPCI-3510M only)
PMC/XMC • One 32-bit/66MHz PMC site or PCIe x1 XMC site if PMC/XMC
daughter board is installed
Audio • Line-in/Line-out on faceplate by Realtek ALC262 High Definition
Audio codec (cPCI-3510(BL)D only)
• Line-in/Line-out on faceplate by 100-pin connector (cPCI-3510M
only)
TPM Atmel AT97SC3204 TPM (upon request) supporting:
• Over/Under voltage detection
• Low/High frequency sensor/filter
• Reset filter
• Memory encryption/decryption
Storage
Interfaces1• CFast or mSATA socket on daughter board
• Optional onboard SSD on daughter board
• One SATA 6Gb/s direct connector for 2.5" SATA drive
(8HP/12HP version only)
BIOS • AMI® EFI BIOS, 64Mbit SPI flash memory
OS
Compatibility • Microsoft Windows 7 32/64-bit • Microsoft Windows 8 32/64-bit
• Red Hat Enterprise Linux 6.4, 64-bit
• Fedora 14, 32-bit
• VxWorks 6.9
• Real Time RTX (MSI)
• Other OS support upon request
Environmental • Operating Temperature (with forced air flow)2:
Standard: -20°C to 70°C
Extreme temperature: -40°C to +85°C (for Intel® Core™
i5-4402E, i7-4700EQ and i7-5700EQ 47W adjusted to 37W
by Intel cTDP and forced air flow)
• Storage Temperature: -50°C to 100°C
• Humidity: 95% @60°C non-condensing
• Shock: 20G peak-to-peak, 11ms duration, non-operating
•Vibration
3: 2Grms, 5-500Hz, each axis, operating (w/o hard drive)
EMI • CE EN55022
• FCC Class A
Table 2-1: cPCI-3510(BL) Processor Blade Specifications