ADLINK Technology NuIPC cPCI-3700 User manual

NuIPC
cPCI-3700
3U CompactPCI All-in-one
Socket 370 CPU Module
User’s Guide

@Copyright 1999~2000 ADLINK Technology Inc.
All Rights Reserved.
Manual Rev. 1.10: 26 June 2000
The information in this document is subject to change without prior notice in
order to improve reliability, design and function and does not represent a
commitment on the part of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental,
orconsequentialdamagesarisingoutoftheuseor inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights
are reserved. No part of this manual may be reproduced by any mechanical,
electronic, or other means in any form without prior written permission of the
manufacturer.
Trademarks
NuIPC is a registered trademark of ADLINK Technology Inc. Other product
names mentioned herein are used for identification purposes only and may be
trademarks and/or registered trademarks of their respective companies.

Getting service from ADLINK
Customer Satisfaction is always the most important thing for ADLINK
Technology Inc. If you need any help or service, please contact us and get it.
ADLINK Technology Inc.
Web Site http://www.adlink.comtw
Sales & Service [email protected]
Technical NuDAQ [email protected]
Support NuDAM [email protected]
NuIPC [email protected]
NuPRO [email protected]
Software [email protected]
TEL [phone] FAX [phone]
Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan, R.O.C.
Please inform or FAX us of your detailed information for a prompt, satisfactory
and constant service. Detailed Company Information
Company/Organization
Contact Person
E-mail Address
Address
Country
TEL FAX
Web Site
Questions
Product Model
¨OS
¨Compute
Environment to Use ¨M/B : ¨CPU :
¨Chipset : ¨Bios :
¨Video Card :
¨Network Interface Card :
¨Other :
Challenge Description
SuggestionstoADLINK

Contents • i
Contents
Chapter 1 Introduction......................................1
1.1 Checklist..................................................................1
1.2 Description..............................................................1
1.3 Features...................................................................2
1.4 Specifications..........................................................2
1.5 Intelligence..............................................................4
Chapter 2 Installation........................................5
2.1 CPU Installation ......................................................5
2.2 Memory Installation ................................................6
2.3 Jumpers on the cPCI-3700.....................................6
2.4 Connectors on the cPCI-3700...............................8
2.4.1 The cPCI-3700 Processor Board........................................8
2.4.2 USB Connectors......................................................................9
2.4.3 Parallel Port Connector.........................................................9
2.4.4 COM1 Serial Ports..................................................................9
2.4.5 PS/2 Keyboard Connector...................................................10
2.4.6 PS/2 Mouse Connector........................................................10
2.4.7 VGA CRT Connector..............................................................10
2.4.8 JP4: IrDA Connector.............................................................12
2.4.9 EIDE Connector......................................................................12
2.4.10 J6:CPU Fan Power Connector............................................14
2.4.11 Floppy Drive Connector.......................................................14
2.4.12 CompactPCI Connectors.....................................................15
2.5 Watchdog Timer Configuration..........................17
Chapter 3 BIOS Configuration ......................19
3.1 BIOS Introduction.................................................19
3.2 BIOS Setup............................................................19
Chapter 4 Bus Master IDE Driver Installation
21
4.1 System Requirements..........................................21
4.2 Installing the Software.........................................21

ii •Contents
Chapter 5 VGA Driver Installation................ 24
5.1 Installing the Drivers for Windows 95............... 24
5.2 Installing the Drivers for Windows 98............... 25
5.3 Installing the Drivers for Windows NT 4.0........ 25
Chapter 6 System Monitor Utility ................. 26

Introduction •1
1
Introduction
Thismanualisdesignedtogiveyouinformation on the cPCI-3700 CPU module.
The topics covered in this chapter are as follows:
ØChecklist
ØDescription
ØFeatures
ØSpecifications
1.1 Checklist
Pleasecheckthatyourpackageiscompleteandcontainstheitemsbelow.Ifyou
discover damaged or missing items, please contact your dealer.
ØThe cPCI-3700 module
ØThis User’s Manual
ØADLINK All-in-one CD
1.2 Description
ThecPCI-3700isaSocket-370 processor board for 3U CompactPCI form factor.
The board is based on the Intel 440BX chipset and is fully designed for harsh
industrial environment. It features a Socket-370 processor connector that is
compatible with Intel Celeron processors.

2• Introduction
1.3 Features
ØCPU Speed 300~533MHz, Intel Celeron processors
ØBus Speed 66MHz
ØIntel 440BX AGPset
ØSODIMM socket support up to128 SDRAM system memory
ØC&T 69000 VGA chipset for CRT displays
ØTwoRS-232 serial ports, one is on the front I/O, the another is on the J2
rear I/O
Ø16 level programmable watchdog timer, from 0-30 seconds
ØHigh speed bi-directional SPP/ECP/EPP parallel port
ØHardware Monitoring
1.4 Specifications
ØProcessor Socket:Socket 370 connector
ØProcessor:Intel Celeron 300~533MHz
ØBus Speed: 66MHz
ØChipset:Intel 440BX AGPset with PCI EIDE and RTC built-in
ØSecondary Cache:CPU integrated
ØMemory Socket:
•One SO-DIMM socket
•Max. 128MB SDRAM
•Memory type: SDRAM (Synchronous DRAM)
ØBIOS: Award BIOS, PnP support
•FLASH EEPROM (256KB) for BIOS update
•Power management

Introduction •3
ØDMI BIOS Support: Desktop Management Interface (DMI) allows users
todownloadsystemhardware-levelinformation such as CPU type, CPU
speed, internal / external frequencies and memory size.
ØMulti I/O: Winbond W83977TF
ØParallel Port:One high-speed parallel port, SPP/EPP/ECP mode
ØSerial Port: Two 16550 UART compatible ports configurable as RS232,
COM1 at front panel and COM2 at J2 rear I/O connector.
ØEnhanced IDE: Bus Mastering EIDE, one internal EIDE interfaces,
support Ultra DMA/33 IDE hard disk. A 2.5” inch hard disk is default
installed. To install DOM is possible.
ØFDD: One floppy drives is default installed (360KB, 720KB, 1.2MB,
1.44MB). In two-slots width version of cPCI-3700, no FDD space is
available.
ØCRT: C&T 69000 chipset
•Embedded 2MB SDRAM display memory
•1280x1024x8bpp colors CRT resolution
ØUSB Interface: TwoUSBconnectors,compliantwithUSBSpecifications
Rev. 1.1
ØDiskOnChip: The SSD interface supports M-Systems DiskOnChip flash
disk supports system boot and storage capacity from 2MB to 144MB.
ØWatchdog Timer:16-level, programmable
•I/O port 0443H to enable watchdog.
•I/O port 0441H to disable watchdog.
•Time-out timing select 0/2/4/6/8/10/12/14/16/18/20/22/ 24/26/28/30
seconds (+/-20%).
ØGreen Function:Power management via BIOS, activated through
mouse/keyboard movement
ØKeyboard and Mouse Connectors:PS/2 type mini-DIN that supports
PC/AT; supports a 5-pin external keyboard connector
ØEnvironmental and Mechanical:
•Temperature:0°C to 60°C
•Humidity:5% to 95%
•PCB Layer:8 layers
•Dimensions: 100mm x 160mm (3.94"x 6.3") for PCB
•Full Dimensions:128mm x 160mm x 60 mm (3-slot)

4• Introduction
1.5 Intelligence
ØTemperature Monitoring and Alert:A sensor for the CPU temperature
on the cPCI-3700 monitors the CPU temperature and alerts the user
through the speaker or buzzer when temperature exceeds the safe heat
level.

Installation •5
2
Installation
Thischapterprovidesinformationonhowtouse the jumpers and connectors on
the cPCI-3700 in order to set up a workable system. The topics covered are:
ØCPU Installation
ØMemory Installation
ØJumpers on the cPCI-3700
ØConnectors on the cPCI-3700
ØWatchdog Timer Configuration
2.1 CPU Installation
The cPCI-3700 Processor Board supports a Socket 370 connector
processor socket for Intel Celeron processors. The CPU is default shipped
with cPCI-3700. For those OEM version of cPCI-3700, please follow up the
following note to install the CPU.
TheSocket370connectorusesastandardPGAsocketconnector.Toinstall
the CPU, insert it to the socket by aligning the notch of the Socket 370 CPU
with the one of the PGA socket.
After you have installed the processor into place, check if the jumper setting
for the CPU speed is correct.
NOTE: 1.
EnsurethattheCPUheatsink and the CPU top surface arein
tightly contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
2.TheCPUheatsinkandfanshouldbeinstalledtightlyt
oo. The

6• Installation
FANconnector3-
pin type. It is recommend to come with speed
sensor.
2.2 Memory Installation
The cPCI-3700 Industrial CPU Card supports one SO-DIMM socket for a
maximum total memory of 128MB. The memory type must be SDRAM. The
memory is default installed, and the size is upon request. The memory
module can come in size of 16MB, 32MB, 64MB, or 128MB SDRAM.
The default memory size installed is 64MB.
2.3 Jumpers on the cPCI-3700
The jumpers on the cPCI-3700 allow you to configure your CPU card
accordingtotheneedsofyourapplications.Ifyouhavedoubtsaboutthebest
jumper configuration for your needs, contact your dealer or sales
representative. The following table lists the connectors on cPCI-3700 and
their respective functions.
ØJP5: Clear CMOS Content
ØJP6: DiskOnChip BIOS Expansion Address Select
ØDSW1 (1-8): Reserved
NOTE: Jumper J19 is for manufacturer testing use only.
JP5: Clear CMOS Content
JP5 Setting Function
1 3 Pin 2-3
Short/Closed Clear CMOS Content
1 3 Pin 1-2
Short/Closed Normal Operation
JP6: DiskOnChip BIOS Expansion Address Select
JP6 Address
13 D0000-D7FFF

Installation •7
13 D8000-DFFFF
(default)

8• Installation
DSW1 (1-8): CPU Frequency Selector (reserved)
The originaldesignofDSW1istomatchtheCPUfrequency. However,
due to the operating frequency of current CPU design is locked
internally. Therefore, no need any adjusting on this switch.
2.4 Connectors on the cPCI-3700
TheconnectorsonthecPCI-3700allowsyoutoconnectexternal devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The following table
lists the connectors on cPCI-3700 and their respective functions.
The cPCI-3700 Processor Board
2.4.1 The cPCI-3700 Processor Board..........................................8
2.4.2 USB Connectors ......................................................................9
2.4.3 Parallel Port Connector...........................................................9
2.4.4 COM1 Serial Ports ...................................................................9
2.4.5 PS/2 Keyboard Connector....................................................10
2.4.6 PS/2 Mouse Connector.........................................................10
2.4.7 VGA CRT Connector..............................................................10
2.4.8 JP4: IrDA Connector..............................................................12
2.4.9 EIDE Connector......................................................................12
2.4.10 J6:CPU Fan Power Connector............................................14
2.4.11 Floppy Drive Connector........................................................14
2.4.12 CompactPCI Connectors .....................................................15
2.4.1 The cPCI-3700 Processor Board
Below shows a picture of the cPCI-3700 processor board and a drawing of
cPCI-3700 board showing the external connectors including USB, mouse,
keyboard, parallel port, COM port and VGA connector.
USB
K/B
Mouse
VGA
Printer port
J2
J1
RS232

Installation •9
2.4.2 USB Connectors
The following table shows the pin outs of the USB connectors.
Pin # Signal Name
1Vcc
2USB-
3USB+
4Ground
2.4.3 Parallel Port Connector
Parallel Port
The following table describes the pin out assignments of this connector.
Signal Name Pin # Pin # Signal Name
Line printer strobe 114 AutoFeed
PD0, parallel data 0 215 Error
PD1, parallel data 1 316 Initialize
PD2, parallel data 2 417 Select
PD3, parallel data 3 518 Ground
PD4, parallel data 4 619 Ground
PD5, parallel data 5 720 Ground
PD6, parallel data 6 821 Ground
PD7, parallel data 7 922 Ground
ACK, acknowledge 10 23 Ground
Busy 11 24 Ground
Paper empty 12 25 Ground
Select 13 N/A N/A
2.4.4 COM1 Serial Ports
Pin # Signal Name
1DCD, Data carrier detect
2RXD, Receive data
3TXD, Transmit data
4DTR,Dataterminalready
5GND, ground
6DSR, Data set ready
Port 1
Port 2
Pin 1

10 • Installation
7RTS, Request to send
8CTS, Clear to send
9RI, Ring indicator
2.4.5 PS/2 Keyboard Connector
Pin # Signal Name
1Keyboard data
2N.C.
3GND
45V
5Keyboard clock
J2 6N.C.
2.4.6 PS/2 Mouse Connector
Pin # Signal Name
1Mouse data
2N.C.
3GND
45V
5Mouse Clock
J3
6N.C.
2.4.7 VGA CRT Connector
The pin assignments of the J4 VGA CRT connector are as follows:
Signal Name Pin Pin Signal Name
Red 12Green
Blue 34N.C.
GND 56GND
GND 78GND
N.C. 910 GND
N.C. 11 12 N.C.
HSYNC 13 14 VSYNC
J4
NC 15

Installation •11

12 • Installation
2.4.8 JP4: IrDA Connector
This connector is used for an IrDA connector for wireless communication. This
connector is an internal connector.
Pin # Signal Name
1+5V
2No connect
3IrRX
4Ground
+5V IrRX IrTX
N.C. GND
JP4 5IrTX
2.4.9 EIDE Connector
Signal Name Pin # Pin # Signal Name
Reset IDE 12Ground
Host data 7 34Host data 8
Host data 6 56Host data 9
Host data 5 78Host data 10
Host data 4 910 Host data 11
Host data 3 11 12 Host data 12
Host data 2 13 14 Host data 13
Host data 1 15 16 Host data 14
Host data 0 17 18 Host data 15
Ground 19 20 Key
DRQ0 21 22 Ground
Host IOW 23 24 Ground
Host IOR 25 26 Ground
IOCHRDY 27 28 Host ALE
DACK0 29 30 Ground
IRQ14 31 32 No connect
Address 1 33 34 No connect
Address 0 35 36 Address 2
Chip select 0 37 38 Chip select 1
J5
Activity 39 40 Ground
+5V 41 42 +5V
Ground 43 44 No connect