Advantech Celeron M Universal Network Controller with PC/104 Extension... User manual

UNO-2170
Celeron M Universal Network
Controller with PC/104 extension
User Manual

Copyright
This document is copyrighted, © 2004. All rights are reserved. The origi-
nal manufacturer
reserves the right to make improvements to the products
described
in this manual at any time without notice.
No part of this manual may be reproduced, copied, translated or transmit-
ted in any form or by
any means without the prior written permission of the
original manufacturer. Information provided in
this manual is intended to
be accurate
and reliable. However, the original manufacturer assumes no
responsibility for its use, nor for any infringements upon the rights of third
parties that may result from such use.
Acknowledgements
IBM, PC/AT, PS/2 and VGA are trademarks of International Business
Machines Corporation.
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft
Corp.
C&T is a trademark of Chips and Technologies, Inc.
All other product names or trademarks are properties of their respective
owners.
Support
For more information on this and other Advantech products, please visit
our websites
at: http://www.advantech.com
For technical support and service, please visit our support website at:
http://www.advantech.com/support/
This manual is for UNO-2170.
Part No. 2002160000
1st Edition, Printed in Taiwan Oct. 2005
UNO-2170 User Manual ii

Product Warranty
Advantech warrants to you, the original purchaser, that each of its products
will be free
from defects in materials and workmanship for one year from the
date
of purchase.
This warranty does not apply to any products that have been repaired or altered
by persons other than repair personnel authorized by Advantech, or which have
been subject to misuse, abuse,
accident or improper installation. Advantech
assumes no liability under the terms
of this warranty as a consequence of such
events.
Because of Advantech high quality-control standards and rigorous testing,
most
of our customers never need to use our repair service. If an Advantech
product
is defective, it will be repaired or replaced at no charge during the
warranty period.
For out-of-warranty repairs, you will be billed according to
the cost of replacement materials, service time and freight. Please consult your
dealer for more details. If you think you have a defective product, follow these
steps:
Step 1. Collect all the information about the problem encountered. (For
example, CPU speed,
Advantech products used, other hardware and
software used,
etc.) Note anything abnormal and list any on- screen
messages you get when the problem occurs.
Step 2. Call your dealer and describe the problem. Please have your man- ual,
product, and any helpful information readily available.
Step 3. If your product is diagnosed as defective, obtain an RMA (return
merchandize
authorization) number from your dealer. This allows us
to process
your return more quickly.
Step 4. Carefully pack the defective product, a fully completed Repair and
Replacement Order Card and
a photocopy proof of purchase date (such
as your sales
receipt) in a shippable container. A product returned
without proof of the purchase date is not eligible for warranty service.
Step 5. Write the RMA number visibly on the outside of the package and ship it
prepaid to your dealer.
iii

UNO-2170 User Manual iv

Contents
Chapter 1 Overview ...........................................................2
1.1 Introduction ....................................................................... 2
1.2 Hardware Specifications ................................................... 3
1.3 Safety Precautions ............................................................. 4
1.4 Chassis Dimensions........................................................... 5
Figure 1.1:Chassis Dimensions....................................... 5
Chapter 2 Hardware Functionality ..................................8
2.1 Introduction ....................................................................... 8
Figure 2.1:Front panel of UNO-2170.............................8
Figure 2.2:Rear panel of UNO-2170 ..............................8
2.2 RS-232 Interface (COM1~COM2) ................................... 8
2.3 RS-232/422/485 Interface (COM3~COM4) ..................... 9
2.3.1 16C550 UARTs with 16-byte standard .......................... 9
2.3.2 RS-422/485 detection ..................................................... 9
2.3.3 Automatic Data Flow Control Function for RS-485 ......9
2.3.4 Termination Resistor (JP6).............................................9
2.3.5 RS-232/422/485 Selection............................................10
Figure 2.3:RS-422/485 jumper setting..........................10
Figure 2.4:RS-232 jumper setting................................. 10
2.3.6 RS-485 Auto Flow Control Mode and RS-422 Master/
Slave Mode Selection ...................................................... 11
Table 2.1:Auto Flow Control and RS-422 Slave/Master
Selection ........................................................... 11
2.3.7 IRQ and Address Setting .............................................. 12
Table 2.2:IRQ Setting via switch 1 at SW2.................. 12
Table 2.3:IRQ Setting via switch 1 at SW2.................. 12
2.4 LAN: Ethernet Connector .............................................. 13
2.5 Power Connector ............................................................. 13
2.6 PS/2 Keyboard and Mouse Connector ............................ 13
2.7 USB Connector ............................................................... 13
2.8 PCMCIA: PC Card Slot .................................................. 14
2.9 VGA Display Connector ................................................. 14
2.10 Battery Backup SRAM.................................................... 15
2.10.1 Lithium Battery Specification....................................... 15
Figure 2.5:The location of the lith. battery for SRAM.15
2.11 Reset Button .................................................................... 15
Chapter 3 Initial Setup.....................................................18
3.1 Inserting a CompactFlash™ Card ................................... 18
3.2 Chassis Grounding .......................................................... 18
v Table of Contents

Figure 3.1:Chassis Grounding Connection...................18
3.3 Connecting Power ........................................................... 19
3.4 Installing a Hard Disk ..................................................... 19
3.5 BIOS Setup and System Assignments ............................ 19
Appendix A System Settings and Pin Assignments ..........22
A.1 System I/O Address and Interrupt Assignment............ 22
Table A.1: UNO-2170 System I/O Ports...................... 22
A.2 Board Connectors and Jumpers....................................... 24
Figure A.1:UNO-2170 conn. and jp. locations (fs) ...... 24
Figure A.2:UNO-2170 conn. and jp. locations (bs)......24
A.3 RS-232 Standard Serial Port (COM1~COM2) ............... 26
A.4 RS-232/422/485 Serial Port (COM3~COM4) ................ 27
A.5 Ethernet RJ-45 Connector (LAN1~LAN2) ..................... 27
A.6 Phoenix Power Connector (PWR)................................... 28
A.7 PS/2 Keyboard and Mouse Connector ............................ 28
A.8 USB Connector (USB1~USB2) ...................................... 29
A.9 VGA Display Connector ................................................. 29
Appendix B Programming the Watchdog Timer .............32
UNO-2170 User Manual vi

1
2
Overview
This chapter provides an overview of
UNO-2170s specifications.
Sections include:
• Introduction
• Hardware specification
• Safety precautions
• Chassis dimensions

Chapter 1 Overview
1.1 Introduction
UNO-2170 is an embedded Application Ready Platform (ARP) that can
shorten your development time and offers rich networking interfaces to
fulfill
extensive needs in different projects. Advantech Universal Net-
work
Controller is designed to be a total solution for network enabled
Application Ready Platforms.
Leveraging field-approved and worldwide approved real-time OS
technology, Advantech UNO-2000 series provides a Windows CE .NET
and Windows XP Embedded ready
solution, and supports several
standard networking interfaces, such as Ethernet, Wireless LAN, RS-232/
422/485 and so on. Because of its openness, great expansion capability and
reliable design (fanless and diskless), the UNO-2000 series are ideal
embedded platforms for implementing custom applications for
diversified
applications.
UNO-2170 User Manual 2

1.2 Hardware Specifications
CPU: Up to Celeron-M 1GHz Ultra low-voltage version
Memory: 256/512 MB DDR on board (Default: 256 MB DDR).
Battery-backup RAM: 512 KB Battery-backup RAM
VGA/Keyboard/Mouse: DB-15 VGA Connector, PS/2 keyboard and
mouse
Serial Ports: 2 x RS-232 and 2 x RS-232/422/485 with DB-9 connectors.
Automatic RS-485
data flow control
Serial Speeds: RS-232: 50~115.2 kbps, RS-422/485: 50~921.6 kbps
LAN: Two 10/100 Base-T RJ-45 Ports
USB interface: Two USB ports, USB UHCI, Rev. 1.1 compliant
Printer port: One printer port
PC Card: One PC Card slot. Supports CardBus (Card-32) Card and
16-bit (PCMCIA 2.1/JEIDA4.2) Card.
Supports +5 V, +3.3 V and +12 V @ 120 mA working power
SSD: One internal Type I / Type II CompactFlash card slot
LEDs: Power, IDE, Alarm for RAM Backup Battery
PC/104: Two PC/104 Extension. (Optional)
HDD: HDD extension kit for installation of one standard 2.5" HDD
Anti-Shock: 20 G @ Wall mounting, IEC 68 2-27, half sine, 11 ms w/
HDD50 G
@ Wall mounting, IEC 68 2-27, half sine, 11 ms w/CF
Anti-Vibration: 2 Grms w/CF @IEC 68 section 2-64, random, 5 ~ 500
Hz, 1 Oct./min, 1 hr/axis.0.5 Grms w/ HDD @ IEC 68 section 2-64,
random,
5 ~ 500 Hz, 1 Oct./min, 1 hr/axis
Power supply: 9 ~ 36 VDC
Power consumption: Max. 35 W
Operating temperature: -10~50°C (14~122°F)@ 5~85% relative
humidity.
Relative humidity: 95% @ 40°C
Weight: 1.6 kg
Chassis size (W × L × H): 255 × 152 × 50 mm (10 ″× 6.0 ″× 2.0 ″ )
Software options: Windows XP Embedded, Windows 2000/XP, Windows
CE .NET V5.0
3 Chapter1

1.3 Safety Precautions
The following sections tell how to make each connection. In most cases,
you will simply need
to connect a standard cable.
Warning! Always disconnect the power cord from your chassis
whenever you are working on it.
Do not connect while
the power is on. A sudden rush of power can damage
sensitive electronic components. Only
experienced
electronics
personnel should open the chassis.
Caution! Always ground yourself to remove any static electric
charge
before touching UNO-2170. Modern electronic
devices are very sensitive to static electric charges. Use
a grounding wrist strap at all times. Place all electronic
components on a static-dissipative surface or in a
static-shielded bag.
UNO-2170 User Manual 4

1.4 Chassis Dimensions
Figure 1.1: Chassis Dimensions
5 Chapter1

UNO-2170 User Manual 6

2
2
Hardware Functionality
This
chapter shows how to setup the
UNO-2170s hardware functions, including
connecting
peripherals, setting switches and
indicators.
Sections include:
•
Peripherals
•
RS-232 Interface
• RS-232/422/485 Interface
• LAN / Ethernet Connector
•
Power Connector
• PS/2 Mouse and Keyboard Connector
• USB Connector
•
PCMCIA: PC Card Slot
• VGA Display Connector
• Battery Backup SRAM
•
Reset Button

Chapter 2 Hardware Functionality
2.1 Introduction
The following two figures show the connectors on UNO-2170. The
following
sections give you detailed information about function of each
peripheral.
Figure 2.1: Front panel of UNO-2170
Figure 2.2: Rear panel of UNO-2170
2.2 RS-232 Interface (COM1~COM2)
The UNO-2170 offers two standard RS-232 serial communication inter-
face ports:
COM1 and COM2. Please refer to A.3 for their pin assignments.
IRQ and Address Setting
The IRQ and I/O address range of COM1 and COM2 are listed below:
COM1: 3F8H,
IRQ4
COM2: 2F8H, IRQ3
UNO-2170 User Manual 8

2.3 RS-232/422/485 Interface (COM3~COM4)
The UNO-2170 offers two RS-232/422/485 serial communication
interface
ports: COM3 and COM4. Please refer to Appendix A.4 for their
pin assignments. The default setting of COM3 and COM4 are RS-422/485.
2.3.1 16C550 UARTs with 16-byte standard
Advantech UNO-2170 comes with TI16C550 UARTs containing 16
bytes FIFOs.
2.3.2 RS-422/485 detection
In RS-422/485 mode, UNO-2170 automatically detects signals to match
RS-422 or RS-485 networks. (No jumper change required)
2.3.3 Automatic Data Flow Control Function for RS-485
In RS-485 mode, UNO-2170 automatically detects the direction of
incoming data
and switches its transmission direction accordingly. So no
handshaking signal
(e.g. RTS signal) is necessary. This lets you
conveniently build an RS-485 network with just two wires. More
importantly, application software previously written for half duplex
RS-232
environments can be maintained without modification.
2.3.4 Termination Resistor (JP6)
The onboard termination resistor (120 ohm) for COM3/COM4 can be
used for long distance
transmission or device matching. (Default Open.)
9 Chapter2

2.3.5 RS-232/422/485 Selection
COM3 and COM4
support 9-wire RS-232, RS-422 and RS-485 inter faces.
The system detects RS-422 or RS-485 signals automatically in RS-
422/485 mode.
To select between RS-422/485 and RS-232 for COM3, adjust JP4.
To select
between RS-422/485 and RS-232 for COM4, adjust JP5.
Jumper setting for RS-422/485 interface: (Default setting). (JP4 and JP5)
Figure 2.3: RS-422/485 jumper setting
Jumper setting for RS-232 interface: (JP4 and JP5)
Figure 2.4: RS-232 jumper setting
UNO-2170 User Manual 10

2.3.6 RS-485 Auto Flow Control Mode and RS-422 Master/Slave
Mode Selection
You can set the “Auto Flow
Control mode of RS-485 or “Master/Slave ＂ mode
of RS-422
by using the SW3 DIP switch for each RS-422/485 port. In RS-485,
if the switch is set to “Auto ＂ the driver automatically senses the direction of
the data
flow and switches the direction of transmission. No handshaking is
necessary.
In RS-422, if DIP switch is set to “On ＂ , the driver is always enabled, and
always in high or
low status.
11 Chapter2

2.3.7 IRQ and Address Setting
The IRQ and I/O address range
of COM3 and COM4 are listed below:
COM3: 3E8H, IRQ10 (Independent IRQ), IRQ10 (Share IRQ)
COM4: 2E8H, IRQ5 (Independent IRQ), IRQ10 (Share IRQ)
Vector address for share IRQ: 1D0H
You can set “Share IRQ ＂ or “Independent IRQ ＂ by the first switch of
SW4.
Table 2.2: IRQ Setting via switch 1 at SW4
Switch 1 at SW4 setting Function
Shared IRQ (Default)
Independent IRQ
You can adjust the transmission rate by the second switch of SW2.
Table 2.3: Speed Setting via switch 2 at SW4
Switch 2 at SW4 setting Function
Speed X 8*
Speed X 1 (Default)
* To increase the normal baud rates by eight times, (e.g. if 115.2K bps is set,
the baud rate will be increased
to 921.6K bps), set switch 2 of SW2 to
“on
＂
UNO-2170 User Manual 12

2.4 LAN: Ethernet Connector
The UNO-2170 is equipped with a Realtek RTL8139C Ethernet LAN
controller
that is fully compliant with IEEE 802.3u 10/100Base-T
CSMA/CD standards.
The Ethernet port provides a standard RJ-45 jack
on board,
and LED indicators on the front side to show its Link (Green
LED) and
Active (Yellow LED) status.
2.5 Power Connector
The UNO-2170 comes with a Phoenix connector that carries 9~36 VDC
external power input,
and features reversed wiring protection. Therefore, it
will not cause any damage to the system
by reversed wiring of ground line
and
power line. Please refer to Appendix A.6
2.6 PS/2 Keyboard and Mouse Connector
The UNO-2170 provides a PS/2 keyboard and PS/2 mouse connector. A
6-pin mini-DIN connector is located on the rear panel of the UNO-2170.
The
UNO-2170 comes with an adapter to convert from the 6-pin mini- DIN
connector to two
6-pin mini-DIN connectors for PS/2 keyboard and PS/2
mouse connection. Please refer to
Appendix A.7 for its pin assignments.
2.7 USB Connector
The USB connector is used for connecting any device that conforms to the
USB interface. Many recent digital devices conform to this standard. The
USB interface supports Plug and Play,
which enables you to connect or
disconnect a device whenever
you want, without turning off the computer.
The UNO-2170 provides two connectors of USB interfaces, which gives
complete Plug &
Play and hot swapping for up to 127 external devices.
The USB interface complies
with USB UHCI, Rev. 2.0 compliant. The
USB
interface can be disabled in the system BIOS setup. Please refer to
Appendix A.8 for its pin
assignments.
13 Chapter2

2.8 PCMCIA: PC Card Slot
The UNO-2170 provides one PC Card slot that supports CardBus (Card-
32) cards and 16-bit (PCMCIA 2.1/JEIDA 4.2) card standards. It supports
+3.3 V, +5 V and +12 V @ 120 mA working voltage. The PC Card is
85.6 mm long by 54 mm wide (3.37" x 2.126"), use a 68-pin connector
and a
removable module standardized by PCMCIA that is known as
“PCMCIA card ＂ .
PS: PCMCIA interrupt assignment is IRQ 9.
2.9 VGA Display Connector
The UNO-2170 provides a VGA controller (Intel 855/852 GME, supports a
single 1.5V accelerated graphics port interface) for a
high resolution VGA
interface. It supports CRT Mode: 1280 x 1024 @ 32bpp (60Hz), 1024 x 768
@ 32bpp (85Hz); LCD/Simultaneous Modes: 1280 x 1024 @ 16bpp(60Hz),
1024 x 768 @16bpp(60Hz)
and up to 32 MB shared memory.
The VGA interface is reserved for
system testing and debugging. The
UNO-2170's JP8 is
a 6-pin mini connector and CN7 is a 15-pin connector for
a VGA monitor. A VGA cable is attached to convert from a 6-pin mini
connector to
standard VGA connector. You can choose one of the VGA
interfaces for system
testing and debugging. Pin assignments for the VGA
display are detailed in
Appendix A.9.
UNO-2170 User Manual 14