Advantech HIT-W18 Series User manual

User Manual
HIT-W18 Series
Healthcare Infotainment
Terminal

HIT-W18 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2011
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Declaration of Conformity
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Part No.2008W18100 Edition 1
Printed in Taiwan September 2011
Warning! Any changes or modifications made to the equipment which are not
expressly approved by the relevant standards authority could void your
authority to operate the equipment.
Caution! Danger of explosion if battery is incorrectly replaced. Replace only with
the same or equivalent type recommended by the manufacturer. Dis-
pose of used batteries according to the manufacturer's instructions.

iii HIT-W18 User Manual
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to
the user's manual.
e. The equipment has been dropped and damaged.
Warning! 1. Input voltage rated 18-19 VDC, 3 A (DC Mode).
2. Packing: please carry the unit with both hands, handle with care.
3. Maintenance: to properly maintain and clean the surfaces, use only
approved products or clean with a dry applicator.

HIT-W18 User Manual iv
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. If your computer clock loses a significant amount of time or the BIOS configura-
tion resets to default, the battery has no power.
17. CLASSIFICATION:
–Supplied by Class I adapter
–No applied parts
–Continuous operation
–No AP or APG category
18. Follow national requirements to dispose of unit.
19. Maintenance: To properly maintain and clean the surfaces, use only approved
products or clean with a dry cloth.
20. Contact information:
No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Taiwan 114,
R.O.C
TEL: [phone]
21.
22. This equipment is not to be used as a life support system.
23. Accessory equipment connected to the analog and digital interfaces must be in
compliance with the respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)
Furthermore all configurations must comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part
or signal output part is configuring a medical system, and is therefore, responsi-
ble that the system complies with the requirements of the system standard IEC
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC 60XXX certified equipment out-
Caution! 1. Do not replace power adaptor yourself. Please contact a qualified
technician or your retail.
2. The computer is provided with a battery-powered real-time clock
circuit. There is a danger of explosion if battery is incorrectly
replaced. Replace only with same or equivalent type recom-
mended by the manufacture. Discard used batteries according to
the manufacturer’s instructions
3. Cleaning: During normal use of the HIT-W151 may become soiled
and should, therefore, be cleaned regularly. Agents: Alcohol or
water.
4. End of Product: for Environmental protection, please follow
national requirements to dispose of unit.

v HIT-W18 User Manual
side of the patient environment. If in doubt, consult the technical services
department or your local representative.
24. A user must not allow SIP/SOPs and the patient to come into contact with one
another at the same time.
25. The sound pressure level at theoperator's position according to IEC 704-1:1982
is no more than 70dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.
Explanation of Graphical Symbols
Caution! Use suitable mounting apparatus to avoid risk of injury.
Note! Attention, please thoroughly consult the accompanying documentation.
Note! Environmental protection
Follow national requirements to dispose of unit.
IEC 60878 and ISO 3864-B.3.6 : Warning: dangerous voltage.
ISO 7000-0434 : Attention, consult ACCOMPANYING DOCUMENTS.
ISO 7000-1641 : Follow operating instructions or Consult instructions for use.
IEC 60417 -5009 : SANDY-BY.
IEC 60417-5031 : Direct current.

HIT-W18 User Manual vi
Disposing of your old product
Within the European Union
EU-wide legislation, as implemented in each Member State,
requires that waste electrical and electronic products carrying the
mark (left) must be disposed of separately from normal household
waste. This includes monitors and electrical accessories, such as
signal cables or power cords. When you need to dispose of your
display products, please follow the guidance of your local authority,
or ask the shop where you purchased the product, or if applicable,
follow any agreements made between yourself. The mark on elec-
trical and electronic products only applies to the current European
Union Member States.

vii HIT-W18 User Manual
Contents
Chapter 1 Introduction..........................................1
1.1 Overview...................................................................................................2
1.2 System Configuration................................................................................4
Chapter 2 Hardware Description .........................5
2.1 General Specifications ..............................................................................6
2.1.1 Standard PC Functions.................................................................6
2.1.2 Flat Panel Interface.......................................................................6
2.1.3 Module Feature.............................................................................6
2.1.4 Power Environmental....................................................................7
2.2 Mechanical Specifications.........................................................................7
2.2.1 Mechanical Specifications (Terminal)...........................................7
2.2.2 Mechanical Specifications (Terminal with Handset) .....................8
2.2.3 Mechanical Drawing for Button and Rear I/O .............................10
2.3 External View..........................................................................................10
2.3.1 Front View...................................................................................10
2.3.2 Side View....................................................................................11
2.3.3 Rear View ...................................................................................12
Chapter 3 Software Description.........................13
3.1 Windows XP Embedded Software Specifications...................................14
Chapter 4 Design Requirements........................15
4.1 Environmental Specifications..................................................................16
4.2 Reliability.................................................................................................16
Chapter 5 Installation..........................................17
5.1 Terminal Installation................................................................................18
5.2 Handset Installation.................................................................................19
5.3 Remote Controller Installation.................................................................20
5.4 Arm Installation .......................................................................................21
Appendix A Annex..................................................23
A.1 Annex......................................................................................................24

HIT-W18 User Manual viii

Chapter 1
1Introduction
This chapter briefly introduces the
HIT-W18 Series product.
Sections include:
Overview
System Configuration

HIT-W18 User Manual 2
1.1 Overview
The HIT-W18 Series Patient Infotainment Terminal is a standard product from Advan-
tech with Windows XP Embedded OS built-in. In addition to providing hospital bed-
side patient information, remote monitoring, and care functions, the CPU and the
LAN-enabled architecture of the HIT-W18 Series terminal also serves as an inte-
grated hospital gateway device. The HIT-W18 Series equipped with an Intel Atom
processor, 18.5 W touchscreen, onboard Ethernet, and audio, plays a key role as a
hospital bedside care and monitoring solution. It connects the service calls and LED
light signals of a hospital room through the LAN to the hospital administration center
or nurse station.

3 HIT-W18 User Manual
Chapter 1 Introduction
Note! Power LED: color in green shows power on, no color shows power off
Indicator LED: It can show color in orange/green and the definitioni is
controlled/defined by customer.

HIT-W18 User Manual 4
1.2 System Configuration
The block diagram of a HIT-W18 Healthcare Infotainment Terminal based on Hospital
bedside environment is shown in the following diagram:

Chapter 2
2Hardware Description
This Chapter describes the hard-
ware features of the HIT-W18.
Sections include:
General Specifications
Mechanical Specifications
External View

HIT-W18 User Manual 6
2.1 General Specifications
2.1.1 Standard PC Functions
2.1.2 Flat Panel Interface
Power button: With LED indicator
Audio: Mic-in, Line-out
USB: USB x 3
LAN: Gigabit LAN
SPK+MIC: build-in 2 x 2 W SPK + EM147 MIC
Button: GPIO Programmable function
Smart card reader: ISO7816 for IC card standard, PC/SC 1.0 for windows,
smart card standard, Microsoft WHQL, EMV for Europay MasterCard Visa stan-
dard and USB-IF CCID standard
2.1.3 Module Feature
Category Specifications
CPU Intel PineView (D525) 1.8 GHz Or
SandyBridge (i7) 1.5 GHz
Front Side Bus Supports FSB 800 MHz
System Chipset Intel D525 + ICH8M/Intel i7 + Cougar Point
Memory DDR2 667 200-pin SODIMM x 2
Storage CFAST or SATA HDD interface (Optional)
Bus Expansion Mini PCIe x 2
Features Interface Description
Wi-Fi Wireless Mini PCIe 802.11b&g&n
RFID Kit Internal USB 13.56 MHz, ISO-15693/14443
Camera module Internal USB 2 M pixels CMOS camera LED
LED module GPIO Programmable, orange light handset
Handset module RJ12 Build-in SPK & MIC
Remote controller RJ12 Micro controller, up to 9 keys
Factory setting connector
port 2 Pin Connector For factory setting only, not for operator to use.

7 HIT-W18 User Manual
Chapter 2 Hardware Description
2.1.4 Power Environmental
Power adaptor: AC/DC
–Input voltage: 100 Vac ~ 240 Vac
–Output voltage: 19 V @ 3.79 A
Medical adaptor: AC/DC (PCM80PS18)
–Input voltage: 100 Vac ~ 240 Vac
–Output voltage: 18 V @ 4.44 A
2.2 Mechanical Specifications
2.2.1 Mechanical Specifications (Terminal)
System Dimensions: 465.9 (W) x 338.5 (H) x 51.2 (D) mm
Front Cover
Environmental
Specifications
Operating Temperature 0 ~ 40° C
Relative Humidity 10 - 95% @ 40° C non-condensing
Operating Humidity 20% to 90% (No Condensation)
Operating Atmospheric Pressure 700 - 1060 hPa
Storage Humidity 10% - 95% (No Condensation)
Storage Atmospheric Pressure 700 - 1060 hPa
Transportation Temperature -20 - 60 °C
Transportation Humidity 10% - 95% (No Condensation)
Transportation Atmospheric
Pressure 700 - 1060 hPa
Vibration 1 G
Shock 10 G peakl acceleration (11 msec, dura-
tion )

HIT-W18 User Manual 8
Carton Dimensions: 620 (W) x 540 (H) x 180 (D) (excludes accessories box)
Mounting System: Back box for wall mounting
Gross Weight: 6.1 kg
Net Weight: 6.1 kg
VESA Mount: 75*75 mm or 100*100 mm
SCREWS: M4*10 mm
IPX0
Cleaning Instruction:
During normal use of the HIT-W18 may become soiled and should, therefore, be
cleaned regularly. Agents: Alcohol or water.
Rear Cover:
2.2.2 Mechanical Specifications (Terminal with Handset)
System Dimensions: 494.5(W) x 392.2(H) x 73.5(D) mm

9 HIT-W18 User Manual
Chapter 2 Hardware Description
Front Cover:
Rear Cover:

HIT-W18 User Manual 10
2.2.3 Mechanical Drawing for Button and Rear I/O
2.3 External View
2.3.1 Front View
Front View (Terminal)

11 HIT-W18 User Manual
Chapter 2 Hardware Description
2.3.2 Side View

HIT-W18 User Manual 12
2.3.3 Rear View
Rear View (Terminal)