Afag CR 25 Quick reference guide

Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 1–56
Assembly & Operating Instructions
Compact Rotary Modules
CR 25 CR 32
Translation of the Original Assembly Instructions EN
CR 25  Order no.: 50254300
CR 32  Order no.: 50254301

2 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
Dear Customer,
Thank you for choosing our products and placing your trust and confidence in
our company!
These assembly and operating instructions contain all essential information you
need about your product. Our aim is to provide the required information as
concisely and clearly as possible. If, however, you still have any questions on
the contents or suggestions, please do not hesitate to contact us. We are always
grateful for any feedback.
Our team will also be glad to answer any further question you may have
regarding the rotary module or other options.
We wish you every success with our products!
With kind regards
Your Afag team
© Subject to modifications
The rotary modules have been designed by Afag Automation AG according to
the state of the art. Due to the constant technical development and improvement
of our products, we reserve the right to make technical changes at any time.
© Copyright 2020 Afag Automation AG
All contents of the present assembly and operating instructions, in particular the
texts, photographs and graphics, are protected by copyright. All rights reserved.
No part of these assembly and operating instructions may be reproduced,
distributed (made available to third parties), or transmitted in any form or by any
means, including photocopying, recording, or other electronic or mechanical
methods, without the prior written permission of Afag Automation AG.
Afag Automation AG
Fiechtenstrasse 32
CH - 4950 Huttwil (Switzerland)
Tel.: [phone]
Fax.: [phone]
e-mail: [e-mail]
Internet: www.afag.com

Table of contents
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 3–56
Table of contents
1General .................................................................................................................... 6
1.1 Contents and purpose of these assembly instructions................................. 6
1.2 Explanation of symbols................................................................................. 6
1.3 Additional symbols........................................................................................ 8
1.4 Applicable documents .................................................................................. 8
1.5 Warranty ....................................................................................................... 8
1.6 Liability.......................................................................................................... 9
2Safety instructions............................................................................................... 10
2.1 General ....................................................................................................... 10
2.2 Intended use ............................................................................................... 10
2.3 Foreseeable misuse ................................................................................... 10
2.4 Obligations of the operator and the personnel ........................................... 11
2.4.1 Observe the assembly instructions ...................................................... 11
2.4.2 Obligations of the operating company.................................................. 11
2.4.3 Obligations of the personnel ................................................................ 12
2.5 Personnel requirements ............................................................................. 12
2.5.1 Personnel qualification ......................................................................... 12
2.6 Personal protective equipment (PPE) ........................................................ 13
2.7 Changes and modifications ........................................................................ 14
2.8 General hazards / Residual Risks .............................................................. 14
2.8.1 General hazards at the workplace ....................................................... 14
2.8.2 Danger due to electricity ...................................................................... 15
2.8.3 Mechanical hazards ............................................................................. 16
2.8.4 Danger due to pneumatics ................................................................... 16
2.8.5 Danger caused by omitting maintenance work .................................... 16
3Technical data ...................................................................................................... 17
3.1 Rotary module CR 25 ................................................................................. 17
3.1.1 Dimensional drawing CR 25................................................................. 17
3.1.2 Technical data CR 25........................................................................... 18
3.1.1 Preferred combinations CR 25............................................................. 19
3.1.2 Module loads CR 25............................................................................. 20
3.1.3 Load diagrams CR 25 .......................................................................... 21
3.2 Rotary module CR 32 ................................................................................. 22
3.2.1 Dimensional drawing CR 32................................................................. 22
3.2.2 Technical data CR 32........................................................................... 23
3.2.3 Preferred combinations CR 32............................................................. 24
3.2.4 Module loads CR 32............................................................................. 25
3.2.5 Load diagrams CR 32 .......................................................................... 26
4Transport, Packaging and Storage .................................................................... 27
4.1 Safety instructions for transport.................................................................. 27

4 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
4.2 Scope of supply .......................................................................................... 27
4.3 Transport .................................................................................................... 28
4.4 Packaging ................................................................................................... 28
4.5 Storage ....................................................................................................... 29
5Structure and description ................................................................................... 30
5.1 Construction rotary modules ...................................................................... 30
5.2 Product description..................................................................................... 30
5.3 Accessories ................................................................................................ 31
5.3.1 Accessories CR 25, CR 32 .................................................................. 31
5.3.2 Other accessories CR 25, CR 32......................................................... 31
5.4 Fields of application.................................................................................... 32
6Installation, assembly & setting ......................................................................... 33
6.1 Safety instructions for installation & assembly ........................................... 33
6.2 Installation and assembly ........................................................................... 34
6.2.1 Assembly and attachment.................................................................... 34
6.2.2 Tightening torques for screws .............................................................. 36
6.2.3 Connection to the pneumatic system ................................................... 36
6.2.4 Assembling, monitoring, replacement of the sensors .......................... 38
6.2.5 Mounting of additional modules ........................................................... 39
6.3 Settings....................................................................................................... 40
6.3.1 Safety notes for settings....................................................................... 40
6.3.2 Adjusting the angle of rotation.............................................................. 41
6.3.3 Setting of the end positions.................................................................. 42
6.3.4 Setting of the end position damping..................................................... 42
6.3.5 Adjusting the shock absorber............................................................... 43
7Commissioning .................................................................................................... 44
7.1 Safety instructions for commissioning ........................................................ 44
7.2 Commissioning of the modules .................................................................. 44
8Fault elimination................................................................................................... 46
8.1 General notes ............................................................................................. 46
8.2 Safety instructions for troubleshooting ....................................................... 46
8.3 Table Fault causes and remedy ................................................................. 46
8.3.1 Troubleshooting table........................................................................... 46
9Maintenance and repair ....................................................................................... 47
9.1 General notes ............................................................................................. 47
9.2 Safety instructions for maintenance and repair .......................................... 47
9.3 Maintenance activities and maintenance intervals..................................... 48
9.3.1 Overview of the maintenance points .................................................... 48
9.3.2 Compressed air specifications ............................................................. 49
9.3.3 Further maintenance ............................................................................ 50
9.4 Spare parts and repair work ....................................................................... 50

Table of contents
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 5–56
10 Decommissioning, disassembly, disposal........................................................ 51
10.1 Safety instructions for decommissioning, disassembling and disposal...... 51
10.2 Decommissioning ....................................................................................... 51
10.3 Disassembly ............................................................................................... 51
10.4 Disposal...................................................................................................... 52
11 Declaration of incorporation............................................................................... 53

General
6 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
1 General
1.1 Contents and purpose of these assembly instructions
These assembly instructions contain important information on assembly,
commissioning, functioning and maintenance of the rotary modules CR 25,
CR 32 to ensure safe and efficient handling and operation.
Consistent compliance with these assembly instructions will ensure:
permanent operational reliability of the rotary module,
optimal functioning of the rotary module,
timely detection and elimination of defects (thereby reducing maintenance
and repair costs),
prolongation of the rotary module service life.
The illustrations in this manual shall provide you with a basic understanding of
the module and may vary from the actual design of your module.
1.2 Explanation of symbols
The safety notes are marked by a pictogram and a signal word. The safety notes
describe the extent of the hazard.
DANGER
Danger!
This safety note indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING
Warning!
This safety note points out a
potentially hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
Caution!
This safety note points out a potentially dangerous situation which, if not
avoided, can result in minor or slight injuries.
NOTICE
This safety note points out a potentially dangerous situation which, if not
avoided, can cause substantial damage to property and the environment.

General
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 7–56
This note contains important additional information as well as useful tips for
safe, efficient and trouble-free operation of the module.
Further warning signs:
Where applicable, the following standardised symbols are used in this manual
to point out the various potential health risks.
Warning
- Dangerous electrical voltage.
Warning
- Risk of injury from contact with hot surfaces.
Warning
-
Risk of hand and finger injury due to uncontrolled
movements of components.
Warning
- Magnetic field.
Warning
- back injury due to heavy lifting.
Warning
- Risk of injury as a result of parts being flung out!
Warning
- high noise levels.

General
8 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
1.3 Additional symbols
In these assembly instructions the following symbols are used to highlight
instructions, results, references, etc.
Symbol Description
1.
Instructions (steps ...)
 Results of actions
 References to sections
 Enumerations not ordered
1.4 Applicable documents
In addition to the assembly instructions, the following documents must be
observed:
Safety data sheets etc.
Instructions for integrated components (supplier documentation)
Each rotary module is accompanied by a safety information sheet. This
information sheet must be read carefully by every person who carries out work
on
and with the rotary module.
1.5 Warranty
The warranty terms for Afag handling components and handling systems are
the following:
24 months from initial operation and up to a maximum of 27 months from
delivery.
Wear parts (e.g. shock absorbers) are excluded from the warranty.*
The warranty covers the replacement or repair of defective Afag parts. Further
claims are excluded.
* However, a customer has a right to a defect-free product. This does also
apply to defective accessories and wear parts. Normal wear and tear is
excluded from the warranty.
The warranty shall expire in the following cases:
Improper use of the module
Non-observance of the instructions regarding assembly, commissioning,
operation and maintenance of the module
Improper assembly, commissioning, operation and maintenance
Repairs and design changes carried out without prior technical instructions
of Afag Automation AG

General
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 9–56
Removing the serial number from the product
Using the module without shock absorbers or with defective shock absorbers
Inadequate checking of wear parts
Non-observance of the EC Machinery Directive, the Accident Prevention
Regulations, the Standards of the German Electrotechnology Association
(VDE) and these safety and assembly instructions
1.6 Liability
No changes shall be made to the rotary modules CR 25/CR 32 unless described
in this instructions manual or approved in writing by Afag Automation AG.
Afag Automation AG accepts no liability for unauthorized changes or improper
assembly, installation, commissioning, operation, maintenance or repair work.

Safety instructions
10 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
2 Safety instructions
2.1 General
This chapter provides an overview of all important safety aspects to ensure safe
and proper use of the rotary module and optimal protection of personnel.
Failure to follow the directions and safety instructions given in this instructions
manual may result in serious hazards.
2.2 Intended use
The CR 25 / CR 32 rotary modules are used for shock-free gripping/rotating of
loads in non-hazardous atmospheres under the ambient and operating
conditions defined for these modules.
The rotary modules are designed exclusively for gripping payloads that do not
pose any danger to persons, property or the environment during manipulation.
In combination with other modules the rotary modules can be used as a pick &
place Station.
In the chemical industry and in potentially explosive areas, the use of rotary
modules is not permitted without additional safety measures. In such cases,
please consult with the Afag technical department.
The intended use of the module also includes:
observance of all instructions given in this instructions manual,

compliance with the inspection and maintenance work and the
specifications in the data sheets,
using only original spare parts.
2.3 Foreseeable misuse
Any use other than or beyond the intended use described above is considered
a misuse of the rotary module.
Especially the following use is considered a misuse:
Use in potentially explosive atmospheres

Safety instructions
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 11–56
Risks can occur if the module is not used as intended. In the event of
damages caused by improper use the following shall apply:
the operating company shall be solely responsible for such damage, and
Afag does not accept any liability for damages caused by improper use.
2.4 Obligations of the operator and the personnel
2.4.1 Observe the assembly instructions
A basic prerequisite for safe and proper handling of the rotary modules is a good
knowledge of the basic safety instructions.
These assembly instructions, in particular the safety instructions contained
therein, must be observed by all persons working with the rotary modules.
2.4.2 Obligations of the operating company
In addition to the safety instructions given in this manual, the operating company
must comply with the safety, accident prevention and environmental protection
regulations valid for the field of application of the rotary modules.
The operating company is required to use only personnel who:
have the necessary professional qualifications and experience,
are familiar with the basic rules regarding occupational safety and accident
prevention,
have been instructed in the correct handling of the rotary modules,
have read and understood these assembly instructions.
The operating company is also required to:
monitor on an ongoing basis that the personnel work safely considering any
potential hazard involved and the assembly instructions are observed,
ensure that the assembly instructions are always kept at hand at the
installation in which the modules are mounted,
observe and communicate universally applicable laws and regulations
regarding accident prevention and environmental protection,
provide the necessary personal protective equipment (e.g. protective gloves)
and instruct the personnel to wear it and
update the related safety data sheets.
WARNING
Risk of injury if the module is not used as intended!
The improper use of the rotary modules poses a potential hazard to the
personnel.
The rotary module may only be used in a technically perfect condition in
accordance with its intended use and the instructions in this manual and in
compliance with the safety requirements!

Any malfunctions, particularly those that could impair safety, must be
eliminated immediately!

Safety instructions
12 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
2.4.3 Obligations of the personnel
All personnel working with the rotary modules are required to:
read and observe these assembly instructions, especially the chapter on
safety,
observe the occupational safety and accident prevention regulations,
observe all safety and warning signs on the rotary modules,
refrain from any activity that might compromise safety and health.
In addition, the personnel must wear the personal protective equipment
required for carrying out their work. (Chapter 2.6).
2.5 Personnel requirements
2.5.1 Personnel qualification
The activities described in the assembly instructions require specific requisites
at the level of professional qualifications of the personnel.
Personnel not having the required qualification will not be able to asses the risks
that may arise from the use of the rotary modules thus exposing himself and
others to the risk of serious injury. Therefore, only qualified personnel may be
permitted to carry out the described activities on the rotary modules.
Persons whose ability to react is restricted due to the intake of medication or the
like must not interact with the rotary modules.
These installation instructions are intended for skilled personnel (installers,
system integrators, maintenance personnel, technicians), electricians and
operating personnel.
The following is a description of the professional skills (qualifications) required
for carrying out the different activities:
Qualified personnel:
Qualified personnel with appropriate training who are qualified due to their
special know-how and fully familiar with the machine and who have been given
instructions on how to carry out the task entrusted to them safely.
Qualified electrician:
Persons who have obtained their electrical qualifications through appropriate
professional training and complementary courses that enables them to identify
risks and prevent possible hazards resulting from electricity.
Operator (trained personnel):
Authorized persons
who due to their specialized professional training,
expertise and experience are capable of identifying risks and preventing
possible hazards arising from the use of the machine.

Safety instructions
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 13–56
2.6 Personal protective equipment (PPE)
The personal protective equipment serves to protect the personnel from hazards
affecting their safety and health at work.
When working on/with the rotary modules, the personnel must wear the
personal protective equipment assigned by the safety officer of the operating
company or as required by safety regulations. In addition, the personnel is
required to:
wear the personal protective equipment provided by the operating company
(employer),
check the personal protective equipment for proper condition, and
immediately notify the person responsible on site of any defects found on the
personal protective equipment.
Personal protective equipment and the respective mandatory signs:
Protective clothing is a close-
fitting clothing specifically
designed to protect personnel from hazards during work.
Protective gloves
are specifically designed to protect the
personnel against hand injuries (such as
cuts, abrasion,
burns).
Safety shoes
are specifically designed to protect the
personnel against foot injuries from crushing, falling objects or
slipping on slippery surfaces.
Hearing protectors
are required to protect the personnel
against excessive noise levels to prevent noise-
induced
hearing loss.

Safety instructions
14 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
2.7 Changes and modifications
No changes may be made to the rotary modules which have not been described
in these assembly instructions or approved in writing by Afag Automation AG.
Afag Automation AG accepts no liability for unauthorised changes or improper
assembly, installation, commissioning, maintenance or repair work.
The rotary modules may not be changed or modified in any way, except with
the prior written consent of Afag Automation AG.
2.8 General hazards / Residual Risks
Despite the safe design of the machine and the technical protective measures
taken, there still remain residual risks that cannot be avoided, and which present
a non-obvious residual risk when operating the rotary modules.
Observe the safety instructions in this chapter and in the other sections of this
manual to avoid damage to property and dangerous situations for the personnel,
.
2.8.1 General hazards at the workplace
The rotary module has been built according to the state-of-the-art and the
applicable health and safety requirements. However, improper use of the rotary
modules may cause the following hazards to the personnel:
danger to life and limb of the operator or third parties,
on the rotation modules themselves,
Property damage.
Always keep the assembly instructions ready at hand at the workplace!
Please, also observe:
the general and local regulations on accident prevention and environmental
protection.
the safety information sheet for the rotary modules.
WARNING
Danger - Do not use in unsuitable environment!
The rotary modules are designed for use in non explosive atmospheres.
Do not use the rotary modules in potentially explosive atmospheres!

Safety instructions
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 15–56
2.8.2 Danger due to electricity
CAUTION
Danger of injury in the working area of the rotary modules!
Due to the decentralised control system, the operator of the rotary modules
must not necessarily stand next to the rotary modules during operation so
that he may not have a complete view of the working area. Persons in the
working area may be injured.
When operating the rotary modules, ensure a good overview of the entire
working area.

Unauthorized persons must not stay within the working area during
operation.
CAUTION
Risk of injuries due to uncontrolled parts movements!
When operating the rotary modules uncontrolled
movements may occur
which can cause personal injury or property damage.
Only qualified personnel may work with or on the rotary modules.
Read the assembly instructions carefully before carrying out any work on
or with the rotary modules.
CAUTION
Risk of noise-induced hearing loss!
When the rotary modules are installed in a machine or plant, the permissible
noise level may be exceeded depending on the various components, the
environment and the resonance.
The operating company is responsible for en
suring that the permissible
noise levels are observed.
If the noise level exceeds 85 dB(A) in normal operation, the operator must
wear hearing protectors at the workplace.
WARNING
Danger! Risk of electric shock!
If work on electrical components is required, ensure that the work is carried
out properly, failure to do so will cause serious or fatal injuries.

Work on the machine's electrical equipment may only be performed by
skilled electrician or trained personnel under the supervision of a skilled
electrician in accordance with all relevant electrical regulations.

Safety instructions
16 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
2.8.3 Mechanical hazards
2.8.4 Danger due to pneumatics
2.8.5 Danger caused by omitting maintenance work
CAUTION
Danger of injury by moving components!
Limbs can be crushed by moving components!
Work on and with the rotary modules may only be carried out by qualified
personnel.
WARNING
Risk of injury - Do not reach into the system during operation!
There is a risk of injury if the personnel reach into the system during normal
operation.
Never reach into the system during normal operation!
WARNING
Risks by the pneumatic system!
The pneumatic system can pose various hazards that can cause serious or
fatal injuries if the work is carried out improperly.
Only qualified personnel may work with or on the pneumatic system!
The necessary personal protective equipment must be provided and used.
CAUTION
Danger of injury!
Poor or not regularly performed maintenance work may cause malfunction of
the components which may result in injuries.
The due diligence obligations of the operating company include ensuring
that the personnel carrying out maintenance work is appropriately trained
and qualified.

Technical data
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 17–56
3 Technical data
3.1 Rotary module CR 25
3.1.1 Dimensional drawing CR 25
Type CR 25
P G 1/8’’
P1 Clockwise
P2 Counterclockwise
Fig. 1 Dimensional drawing - Rotary module CR 12
On all modules the hole patterns of the flange are set to 0° position. The
flange thus turns 100° to the left and 100° to the right.

Technical data
18 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
3.1.2 Technical data CR 25
CR 25
Attachment grid 96 mm
Attachment grid alternative 60 mm
Attachment thread M10 pass-thr. - M12 f. bottom
Attachment thread alternative M8
Operating pressure 6 +/- 2 bar
Air connection P G 1/8’’
Operating temperature 0 – 50 °C
Storage temperature 0 – 50 °C
Air humidity < 90 %
Medium filtered compressed air 10 – 40 μm
Type CR 25
Order Number 50254300
Net weight 3.28 kg
Air consumption (180°) 0.389 NL
Angle of rotation 0-180°
Min. swivel time 180° 0.44 s
Noise level 54 dB(A)
Electrical feed-through 4 x 1 A
Rotary supply fluids 4
Angle accuracy +/- 0.05°
Torque* 6.2 Nm
Max. mass moment of inertia (observe swivel time diagram) *4000 kg/cm2
Positions 2
Mounting position
Fig. 2 Table technical data CR 25
* In the end position, only half the torque is achieved, since in this position the
pressure is exerted by one piston only (
 chapter 5.4 ).
The technical data refer to a nominal pressure of 6 bar and the Afag standard
test conditions.
Note: If a torque acts against the direction of rotation in the end position,
select a drive with twice the theoretical torque.
The rotary module can be operated with both oil-free and oiled compressed-
air. Change from oil-free to oil-lubricated allowed but not vice versa.
Cleanroom class ISO 14644-1.

Technical data
Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0 19–56
3.1.1 Preferred combinations CR 25
Note that here might be different mounting positions from one module to another one.
The required connection elements and the range of support columns are
depicted in the catalogue “HT Accessories”.

Technical data
20 – 56 Assembly instructions EN CR 25 / CR 32 Edition 01/2020 Rev. 4.0
3.1.2 Module loads CR 25
Type CR 25
Max. force, axial pushing static 2075 N
Max. force, axial pulling static 800 N
Max. force, axial pushing dynamic 430 N
Max. force, axial pulling dynamic 200 N
Max. payload, radial dynamic 891 N
Max. payload, radial static 3635 N
Fig. 3 Table module loads CR 25