AGI A114 User manual

30798 R1
Revised: APRIL 2021 1
A114
Swivel Arc Kit
Assembly and Operator Manual
Applicable Models:
•Westfield WR6, WRX 8/10 Series
•AGI WRX 8/10 Series
•Hutchinson WR6, WRX 8/10 Series
•Mayrath WR6, WRX 8/10 Series
Assembling the Swivel Arc Kit
1. Securely chock wheel on one side of auger.
2. Jack up other wheel and place sturdy support underneath axle close to wheel. Lower weight of auger onto
this support.
3. Remove wheel and hub assembly from spindle. Keep dirt out of hub bearings and grease.
4. Place appropriate left or right swivel kit arm (A) onto spindle (see ). Secure arm with 3/4" slotted nut.
Tighten snug only. Insert cotter pin.
Note
To determine left or right side of a grain auger, stand at intake end facing upper discharge end.
5. Loosely install brackets (B) and (C) to lower undercarriage tubes next to bracket (D) where upper lift arms
are attached. Use two 7/16" x 1" bolts and locknuts and two 7/16" x 3-1/2" or 4" bolts and locknuts.
6. Secure adjust strap (E) to bracket (B) and to swivel arm (A) with two 1/2" x 1-1/4" bolts and locknuts. Adjust
the angle of the wheel with this adjust strap. Securely tighten all bolts installed in Steps 5 and 6.
Note
Since most bin installations require one basic auger height, the angle of the wheels should be
adjusted once this height is determined. To change the angle of the wheels, see below.
7. Secure wheel spindle bracket (F) to arm (A). Tighten securely with 3/4" nut and lockwasher.

2 30798 R1
Figure 1. Assembling the Swivel Arc Kit
8. Assemble hub. First remove dirt and paint from spindle. Wheel bearings should be thoroughly packed with a
high-quality SAE-approved bearing grease. Place hub on spindle, insert small wheel bearing, then tighten 3/
4" slotted nut until hub drags slightly. Back off nut about 1/4 turn until hub turns freely. Install cotter pin
and dust cap.
9. Attach auger wheel to hub with four wheel bolts. Tighten securely. Jack up axle, remove support and lower
jack.
10. Repeat above procedure on other wheel.
Changing the Angle of the Wheels
1. Jack up the axle.
2. Place safety support under axle.
3. Remove the lower 1/2" x 1-1/4" bolt on the adjust strap (E) and change the angle of the wheel as desired.
4. Replace and secure the bolt and locknut.
5. Remove the axle support and jack.
6. Repeat on other wheel.
Changing the Wheel from Swivel to Transport
Or changing the wheel from Transport Position to Swivel Position
1. Jack up the axle.
2. Place the safety support under the axle.
A114 SWIVEL ARC KIT –

30798 R1 3
3. Loosen the 3/4" nut (G) on the swivel arm (A).
4. Change the position of the wheel and re-tighten the 3/4" nut.
5. Remove the axle support and jack.
6. Repeat on other wheel.
Note
If the auger must be transported on the road for any considerable distance at speeds higher than 10
mph (16 km/h), the wheels and hub assemblies should be re-installed on the auger axle spindle.
Note
When moving the auger sideways in the swivel arc position, make certain the area is level and free of
debris. Holes and bumps may cause the auger to upset.
Figure 2. Equipment Decals
P.O. Box 39
Rosenort, Manitoba, R0G 1W0 Canada Website: www.aggrowth.com
Phone: [phone] (Canada & USA) or (204) 746–2396 Email: [email protected]
Fax: [phone] ©Ag Growth International Inc. 2021, Printed in Canada
A114 SWIVEL ARC KIT –