AGI MKX2 Series User manual

LOOKING FOR PARTS?
Check out our online
Parts Catalog!
Read this manual before using product. Failure to
follow instructions and safety precautions can
result in serious injury, death, or property
damage. Keep manual for future reference.
Part Number: 31185 R0
Revised: March 2023
Original Instructions
MKX², X², HX², GMX² 16" Series
Swing-Away Grain Auger
Assembly Manual
This manual applies to:
AGI Westfield MKX² 16-85, 16-105, 16-125
AGI X² 16-85, 16-105, 16-125
AGI Hutchinson HX² 16-85, 16-105, 16-125
AGI Mayrath HX² 16-85, 16-105, 16-125
AGI GrainMaxx GMX² 16-105, 16-125

New in this Manual
The following changes have been made in this revision of the manual:
Description Section
This is a new manual.

MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER
31185 R0 3
CONTENTS
1. Introduction ............................................................................................................................................ 5
2. Safety....................................................................................................................................................... 6
2.1 Safety Alert Symbol and Signal Words...................................................................................... 6
2.2 General Safety Information....................................................................................................... 6
2.3 Rotating Flighting Safety ........................................................................................................... 7
2.4 Rotating Parts Safety................................................................................................................. 7
2.5 Hydraulic Winch Safety ............................................................................................................. 7
2.6 Drives and Lockout Safety......................................................................................................... 8
2.6.1 PTO Driveline Safety................................................................................................... 8
2.6.2 Hydraulic Power Safety .............................................................................................. 9
2.7 Tire Safety................................................................................................................................ 10
2.8 Personal Protective Equipment............................................................................................... 10
2.9 Safety Equipment .................................................................................................................... 11
2.10 Safety Decals ......................................................................................................................... 11
2.10.1 Decal Installation/Replacement............................................................................. 12
2.10.2 Safety Decal Locations and Details ........................................................................ 12
3. Features................................................................................................................................................. 22
4. Assembly ............................................................................................................................................... 24
4.1 Assembly Safety ...................................................................................................................... 24
4.2 Check Shipment....................................................................................................................... 24
4.3 Before You Begin..................................................................................................................... 25
4.4 Tube Layout and Branding Decal Placement .......................................................................... 25
4.5 Connect Auger Tubes .............................................................................................................. 28
4.6 Hydraulic Lift Cylinders............................................................................................................ 30
4.6.1 Install the 85' Hydraulic Lift Cylinders ..................................................................... 30
4.6.2 Install the 105'/125' Hydraulic Lift Cylinders........................................................... 31
4.7 Install the Track Shoe and Track Stop..................................................................................... 33
4.8 Install the Boot on the Auger Tube......................................................................................... 34
4.9 Install the PTO Shield Assembly.............................................................................................. 35
4.10 Install the PTO Bracket Assembly ......................................................................................... 35
4.11 Install the Boot Tow Bar........................................................................................................ 36
4.12 Set the Thrust Adjuster ......................................................................................................... 37
4.13 Install Truss Support Towers and Truss Tubes ..................................................................... 37
4.13.1 High and Low Towers............................................................................................. 37
4.13.2 Top Truss Tube ....................................................................................................... 38
4.13.3 Cross Brace ............................................................................................................. 40
4.14 Install Truss Cables ................................................................................................................ 42
4.15 Assemble the Lower Frame................................................................................................... 44
4.16 Auger Steer Installation......................................................................................................... 46
4.17 Connect the Auger Tube to the Frame ................................................................................. 48
4.18 Install Lift Cylinder Cables to the Lift Assist.......................................................................... 50
4.19 Connect Hydraulic Hoses ...................................................................................................... 52
4.19.1 Connect Hydraulic Auger Steer Hoses ................................................................... 52
4.19.2 Connect Hydraulic Lift Hoses ................................................................................. 54
4.20 Connect the PTO Driveline .................................................................................................... 56
4.21 Connect the Intake Hopper to the Swing Tube .................................................................... 58

MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER
4 31185 R0
4.22 Connect the Spout Head to the Grain Transfer Boot ........................................................... 60
4.23 Install the Hopper Lift Arm.................................................................................................... 62
4.24 Install the Hydraulic Winch ................................................................................................... 63
4.25 Electric Power Swing Assembly............................................................................................. 65
4.25.1 Power Swing Components ..................................................................................... 65
4.25.2 Install the Landing Gear ......................................................................................... 66
4.25.3 Install and Connect the Receiver Box .................................................................... 68
4.26 Hopper Transport Position.................................................................................................... 72
4.27 Install the Hitch Jack.............................................................................................................. 72
4.28 Install the Plastic Manual Holder .......................................................................................... 73
4.29 Install Work Lights................................................................................................................. 74
4.30 Install Transport Lights.......................................................................................................... 75
4.31 Install the Retroreflective Strips ........................................................................................... 77
5. Specifications ........................................................................................................................................ 78
6. Appendix ............................................................................................................................................... 79
6.1 Bolt Torque.............................................................................................................................. 79
7. AGI Limited Warranty........................................................................................................................... 80

31185 R0 5
1. Introduction
Before assembling, please read this manual. Familiarize yourself with the process and the necessary
precautions for efficient and safe assembly of this AGI Swing-Away Grain Auger.
Everyone present at the assembly site is required to be familiar with all safety precautions.
Keep this manual available for frequent reference and review it with new personnel. Call your local
distributor or dealer if you need assistance or additional information.
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 1. INTRODUCTION

6 31185 R0
2. Safety
2.1. Safety Alert Symbol and Signal Words
This safety alert symbol indicates important safety messages in this manual. When you see
this symbol, be alert to the possibility of injury or death, carefully read the message that
follows, and inform others.
Signal Words: Note the use of the signal words DANGER,WARNING,CAUTION, and NOTICE with the safety
messages. The appropriate signal word for each message has been selected using the definitions below as a
guideline.
Indicates an imminently hazardous situation that, if not avoided, will result in serious injury or
death.
Indicates a hazardous situation that, if not avoided, could result in serious injury or death.
Indicates a hazardous situation that, if not avoided, may result in minor or moderate injury.
Indicates a potentially hazardous situation that, if not avoided, may result in property damage.
2.2. General Safety Information
Read and understand all safety instructions, safety decals, and manuals and follow them when assembling the
equipment.
• Only experienced personnel who are familiar with this type of assembly and
installation should perform this work. Untrained assemblers/installers expose
themselves and bystanders to possible serious injury or death.
• Do not modify the auger in any way or deviate from the instructions in this manual without written
permission from the manufacturer. Unauthorized modification or methods may impair the function and/or
safety. Any unauthorized modification will void the warranty.
• Follow a health and safety program for your worksite. Contact your local occupational health and safety
organization for information.
• Contact your local representative or AGI if you need assistance or additional information.
• Always follow applicable local codes and regulations.
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER

31185 R0 7
2.3. Rotating Flighting Safety
• KEEP AWAY from rotating flighting.
• DO NOT remove or modify flighting guards, doors, or covers.
Keep in good working order. Have replaced if damaged.
• DO NOT operate the auger without all guards, doors, and
covers in place.
• NEVER touch the flighting. Use a stick or other tool to
remove an obstruction or clean out.
• Shut off and lock out power to adjust, service, or clean.
2.4. Rotating Parts Safety
• Keep body, hair, and clothing away from rotating shafts,
pulleys, belts, chains, and sprockets.
• Do not operate with any guard removed or modified. Keep
guards in good working order.
• Shut off and lock out power source before inspecting or
servicing machine.
2.5. Hydraulic Winch Safety
When Equipped:
• Keep away from rotating cable drum and winch cable. Do not touch or grab cable while
winch is being operated or use hands to guide the cable.
• Inspect cable and cable clamps before using hydraulic winch. Replace cable if frayed or
damaged. Tighten cable clamps if necessary.
• Check the cable anchor on the winch drum is tight.
• Confirm hydraulic hoses are in good condition.
• Do not continue to supply power to hydraulic winch after the swing hopper is fully lifted.
• Do not disconnect hydraulic quick couplers when lines are pressurized.
• Make sure lift cable is seated in cable pulley.
• Always keep a minimum of 3 cable wraps on the cable drum.
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 2. SAFETY

8 31185 R0
2.6. Drives and Lockout Safety
Inspect the power source(s) before using and know how to shut down in an emergency.
Whenever you service or adjust your equipment, make sure you shut down the power
source and unplug or remove the key (as applicable) to prevent inadvertent start-up and
hazardous energy release. Know the procedure(s) that applies to your equipment from the
following power source(s). Ensure that all personnel are clear before turning on power to
equipment.
2.6.1 PTO Driveline Safety
Drive
• Keep body, hair, and clothing away from rotating PTO
driveline.
• Make certain the driveline shields telescope and rotate freely
on driveline before attaching.
• Make certain the driveline is securely attached at both ends.
• Do not operate auger unless all driveline, tractor, and
equipment shields are in place and in good working order.
• Do not exceed the specified operating speed.
• Keep universal joint angles small and equal. Do not exceed
maximum recommended length for PTO driveline.
• Engage tractor park brake and/or chock wheels.
Lockout
• Position all controls in neutral, shut off tractor’s engine, and remove key from tractor.
• If removing key is impossible, remove PTO driveline from tractor.
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER

31185 R0 9
2.6.2 Hydraulic Power Safety
Power Source
• Refer to the rules and regulations applicable to the power
source operating the hydraulic system.
• Do not connect or disconnect hydraulic lines while system is
under pressure.
• Keep all hydraulic lines away from moving parts and pinch
points.
• Escaping hydraulic fluid under pressure will cause serious
injury if it penetrates the skin surface (serious infection or
toxic reaction can develop). See a doctor immediately if
injured.
• Use metal or wood as a backstop when searching for
hydraulic leaks and wear proper hand and eye protection.
• Check all hydraulic components are tight and in good
condition. Replace any worn, cut, abraded, flattened, or
crimped hoses.
• Clean the connections before connecting to equipment.
• Do not attempt any makeshift repairs to the hydraulic fittings
or hoses with tape, clamps, or adhesive. The hydraulic
system operates under extremely high pressure; such repairs
will fail suddenly and create a hazardous and unsafe
condition.
Lockout
• Always place all hydraulic controls in neutral and relieve
system pressure before disconnecting or working on
hydraulic system.
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 2. SAFETY

10 31185 R0
2.7. Tire Safety
Failure to follow proper procedures when mounting a tire on a
wheel or rim can produce an explosion that may result in
serious injury or death.
• DO NOT attempt to mount a tire unless you have the proper
equipment and experience to do the job.
• Have a qualified tire dealer or repair service perform
required tire maintenance.
• When replacing worn tires, make sure they meet the original
tire specifications. Never undersize the replacement tire.
• DO NOT weld to the tire rim with the tire mounted on the
rim. This action may cause an explosion which could result in
serious injury or death.
• Inflate tires to the manufacturer’s recommended pressure.
• Tires should not be operated at speeds higher than their
rated speed.
• Keep wheel lug nuts tightened to manufacturer’s
recommendations.
• Never reinflate a tire that has been run flat or seriously
under-inflated without removing the tire from the wheel.
Have the tire and wheel closely inspected for damage before
remounting.
2.8. Personal Protective Equipment
The following Personal Protective Equipment (PPE) should be worn when assembling the equipment.
Safety Glasses
• Wear safety glasses at all times to protect eyes from debris.
Coveralls
• Wear coveralls to protect skin.
Hard Hat
• Wear a hard hat to help protect your head.
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER

31185 R0 11
Steel-Toe Boots
• Wear steel-toe boots to protect feet from falling debris.
Work Gloves
• Wear work gloves to protect your hands from sharp and rough edges.
Hearing Protection
• Wear ear protection to prevent hearing damage.
2.9. Safety Equipment
The following safety equipment should be kept on site.
Fire Extinguisher
• Provide a fire extinguisher for use in case of an accident. Store in a highly visible and
accessible place.
First-Aid Kit
• Have a properly-stocked first-aid kit available for use should the need arise, and
know how to use it.
2.10. Safety Decals
• Keep safety decals clean and legible at all times.
• Replace safety decals that are missing or have become illegible. See decal location figures that follow.
• Replaced parts must display the same decal(s) as the original part.
• Replacement safety decals are available free of charge from your distributor, dealer, or factory as applicable.
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 2. SAFETY

12 31185 R0
2.10.1 Decal Installation/Replacement
1. Decal area must be clean and dry, with a temperature above 50°F (10°C).
2. Decide on the exact position before you remove the backing paper.
3. Align the decal over the specified area and carefully press the small portion with the exposed sticky backing
in place.
4. Slowly peel back the remaining paper and carefully smooth the remaining portion of the decal in place.
5. Small air pockets can be pierced with a pin and smoothed out using the decal backing paper.
2.10.2 Safety Decal Locations and Details
Replicas of the safety decals that are attached to the auger and their messages are shown in the figure(s) that
follow. Safe operation and use of the auger requires that you familiarize yourself with the various safety decals
and the areas or particular functions that the decals apply to, as well as the safety precautions that must be
taken to avoid serious injury, death, or damage.
18859
20804 20813
20812
20816
17113
20807
20813
17107
21074
20804
17378
17377
20806
20810
20807
20811
20816
17113
20809
20805
201199
20803
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER

31185 R0 13
Table 1. Safety Decals
Part Number Description
20813
To prevent death or serious injury:
• KEEP AWAY from rotating auger flighting.
• DO NOT remove or modify auger flighting
guards, doors, or covers. Keep in good working
order. Have replaced if damaged.
• DO NOT operate the auger without all guards,
doors, and covers in place.
• NEVER touch the auger flighting. Use a stick or
other tool to remove an obstruction or clean out.
• Shut off and lock out power to adjust, service, or
clean.
ROTATING FLIGHTING HAZARD
DANGER
201199
DANGER
To prevent serious injury or death:
• Keep body, hair, and clothing away from rotating
PTO driveline.
• Do not operate equipment unless all driveline,
tractor, and equipment shields are in place and in
good working order.
• Make certain the driveline shields turn freely on
driveline.
• Make certain the driveline is securely attached at
both ends.
• Do not exceed specified operating speed (see
operator’s manual).
• Keep u-joint angles small and equal. Do not exceed
maximum recommended length for PTO driveline.
ROTATING PTO DRIVELINE
To prevent serious injury or death, do
not operate auger unless swing-hop-
per is securely attached to boot.
ROTATING FLIGHTING INSIDE
DANGER
To prevent damage, wheels must be
free to move when raising or lowering
equipment.
When equipment is positioned, chock
all wheels.
NOTICE
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 2. SAFETY

14 31185 R0
Table 1 Safety Decals (continued)
Part Number Description
20816
DANGER
ELECTROCUTION HAZARD
To prevent death or serious injury:
• When operating or moving, keep equipment
away from overhead power lines and devices.
• Fully lower equipment before moving.
This equipment is not insulated.
Electrocution can occur without direct contact.
17113
To prevent serious injury or death:
• Securely attach equipment to vehicle with
correct pin and safety chains.
• Use a tow vehicle to move equipment.
TRANSPORT HAZARD
WARNING
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER

31185 R0 15
Table 1 Safety Decals (continued)
Part Number Description
20804
To prevent serious injury or death:
• Keep body, hair, and clothing away from rotating
pulleys, belts, chains, and sprockets.
• Do not operate with any guard removed or
modified. Keep guards in good working order.
• Shut off and lock out power source before
inspecting or servicing machine.
ENTANGLEMENT HAZARD
WARNING
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 2. SAFETY

16 31185 R0
Table 1 Safety Decals (continued)
Part Number Description
20811
WARNING
UPENDING HAZARD
To prevent death or serious injury:
• Anchor intake end and/or support discharge end
to prevent upending.
• Intake end must always have downward weight.
Do not release until attached to tow bar or
resting on ground.
• Do not raise intake end above tow bar height.
• Empty tube and fully lower before moving.
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER

31185 R0 17
Table 1 Safety Decals (continued)
Part Number Description
20807
To prevent serious injury or death:
• Read and understand the manual before
assembling, operating, or maintaining the
equipment.
• Only trained personnel may assemble, operate,
or maintain the equipment.
• Children and untrained personnel must be kept
outside of the work area.
• Do not modify the equipment. Keep in good
working order.
• If the manual, guards, or decals are missing or
damaged, contact factory or representative for
free replacements.
• Lock out power before performing maintenance.
• To prevent equipment collapse or upending,
support equipment tube while disassembling
certain components.
• Follow grain storage structure manufacturer's
warnings when loading and unloading.
• Electric motors must be grounded. Disconnect
power before resetting overloads.
WARNING
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 2. SAFETY

18 31185 R0
Table 1 Safety Decals (continued)
Part Number Description
20803
To prevent serious injury or
death, shut off power and
reattach guard before operating
machine.
MISSING GUARD HAZARD
WARNING
20809
To prevent serious injury or death:
• Keep away from rotating cable sheaves and lift cables.
• Inspect lift cable periodically; replace if damaged.
• Inspect cable clamps periodically; tighten if
necessary.
WARNING
20810
To prevent death or serious injury:
• Keep away from rotating cable drum and winch
cable.
• Inspect lift cable periodically; replace if damaged.
• Inspect cable clamps periodically; tighten if necessary.
WARNING
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER

31185 R0 19
Table 1 Safety Decals (continued)
Part Number Description
20805
HIGH PRESSURE FLUID HAZARD
WARNING
Hydraulic fluid can cause serious injury if it
penetrates the skin. If it does, see a doctor
immediately.
• Relieve system pressure before repairing,
adjusting or disconnecting.
• Wear proper hand and eye protection when
searching for leaks. Use wood or cardboard
instead of hands.
Hydraulic fluid can cause serious injury if it
penetrates the skin. If it does, see a doctor
immediately.
• Relieve system pressure before repairing,
adjusting or disconnecting.
• Wear proper hand and eye protection when
searching for leaks. Use wood or cardboard
instead of hands.
20806
HIGH PRESSURE FLUID HAZARD
Hydraulic fluid can cause serious injury if it
penetrates the skin. If it does, see a doctor
immediately.
• Relieve system pressure before repairing, adjusting
or disconnecting.
• Wear proper hand and eye protection when searching
for leaks. Use wood or cardboard instead of hands.
WARNING
20812
To prevent serious injury or death:
• Fully extend axles before raising tube.
• Retract axles before transporting.
ROLLOVER / TRANSPORT
HAZARD
WARNING
MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER 2. SAFETY

20 31185 R0
Table 1 Safety Decals (continued)
Part Number Description
17107
To prevent personal injury or
damage to equipment, close valve
in lift cylinder hydraulic line after
raising equipment into position.
CAUTION
17378
This equipment is not intended for
transport on public roads. If it must
be moved, check local regulations.
To avoid damaging the equipment:
• Be careful when turning corners.
• Watch for low overhead objects.
• Retract axles before transporting unit.
NOTICE
17377
To lower equipment, start tractor,
then engage hydraulic lever in
down position.
• This pumps oil to upper chamber of
the hydraulic cylinders preventing
overfill of tractor reservoir.
NOTICE
2. SAFETY MKX², X², HX², GMX² 16" SERIES – SWING-AWAY GRAIN AUGER